Related Manuals for H3C S3100-26T P-EI-W
Summary of Contents for H3C S3100-26T P-EI-W
- Page 1 H3C S3100 Series Ethernet Switches Quick Start (For Soliton) Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Manual Version: T2-08011H-20080410-C-1.00...
- Page 2 Copyright © 2008, Hangzhou H3C Technologies Co., Ltd. and its licensors All Rights Reserved No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of Hangzhou H3C Technologies Co., Ltd. Trademarks H3C,...
-
Page 3: About This Manual
About This Manual Related Documentation In addition to this manual, each H3C S3100 Series Ethernet Switches documentation set includes the following: Manual Content H3C S3100 Series Ethernet It is used for assisting the users Switches Operation Manual in data configurations and (For Soliton) typical applications. - Page 4 Chapter Contents Introduces the installation preparation and precaution of 2 Installation Preparation S3100 Series Ethernet Switches. Introduces the procedures to install an S3100 Series Ethernet Switch, 3 Installation including the setup of the mainframe, cards and cables. 4 Lightning Protection of the Introduces lightning protection of Switch S3100 Series Ethernet Switches.
-
Page 5: Table Of Contents
Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Table of Contents Table of Contents Chapter 1 Product Overview ............1-1 1.1 Overview ................1-1 1.2 Introduction to S3100 Series Ethernet Switches ....1-2 1.2.1 S3100-26TP-EI-W ...........1-2 1.2.2 S3100-16TP-EI-W ...........1-4 1.2.3 S3100-8TP-EI-W .............1-7 1.3 Introduction to Front Panel LEDs........1-9... - Page 6 Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Table of Contents 3.1.1 Cabinet Mounting ............3-1 3.1.2 Desk Mounting............3-9 3.1.3 Wall Mounting............3-9 3.1.4 Magnet Mounting...........3-12 3.2 Connection of Power Cord and Grounding Cable ...3-16 3.2.1 Connecting AC Power Cord ........3-16 3.2.2 Connecting DC Power Cable ........3-17...
-
Page 7: Chapter 1 Product Overview
H3C S3100 Series Ethernet Switches are high-performance, high-density, easy-to-install, NMS-manageable intelligent Ethernet switches which support wire-speed Layer 2 switching. Table 1-1 lists the models of H3C S3100 Series Ethernet Switches. Table 1-1 Models of H3C S3100 Series Ethernet Switches Number of... -
Page 8: Introduction To S3100 Series Ethernet Switches
Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Chapter 1 Product Overview 1.2 Introduction to S3100 Series Ethernet Switches 1.2.1 S3100-26TP-EI-W I. Front panel S3100-26TP-EI-W Ethernet switches each provide twenty-four auto-sensing 10/100/1000Base-TX Ethernet ports, 10/100/1000BASE-T Ethernet ports, two 100/1000Base-X SFP ports, and one console port. - Page 9 Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Chapter 1 Product Overview Note: For details about LEDs on the front panel, refer to section 1.3 “Introduction to Front Panel LEDs”. II. Rear panel Figure 1-2 shows the rear panel of an S3100-26TP-EI-W Ethernet switch.
-
Page 10: S3100-16Tp-Ei-W
Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Chapter 1 Product Overview IV. Cooling system S3100-26TP-EI-W Ethernet switches cool off naturally. 1.2.2 S3100-16TP-EI-W I. Front panel S3100-16TP-EI-W Ethernet switches each provide sixteen auto-sensing 10/100Base-TX Ethernet ports, two 10/100/1000Base-T Ethernet ports, two 100/1000Base-X SFP ports, and one console port. - Page 11 Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Chapter 1 Product Overview Note: For details about LEDs on the front panel, refer to section 1.3 “Introduction to Front Panel LEDs”. II. Rear panel Figure 1-4 shows the rear panel of an S3100-16TP-EI-W Ethernet switch.
- Page 12 Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Chapter 1 Product Overview (1) Security slot Figure 1-5 Security slot on left side panel of an S3100-16TP-EI-W Ethernet switch Note: If the left screw hole above the security slot is used, the security slot cannot be used.
-
Page 13: S3100-8Tp-Ei-W
Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Chapter 1 Product Overview 1.2.3 S3100-8TP-EI-W I. Front panel S3100-8TP-EI-W Ethernet switches each provide eight auto-sensing 10/100Base-TX Ethernet ports, one 10/100/1000Base-T Ethernet port, one 100/1000Base-X SFP port, and one console port. - Page 14 Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Chapter 1 Product Overview Note: For details about LEDs on the front panel, refer to section 1.3 “Introduction to Front Panel LEDs”. II. Rear panel Figure 1-7 shows the rear panel of an S3100-8TP-EI-W Ethernet switch.
-
Page 15: Introduction To Front Panel Leds
Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Chapter 1 Product Overview Note: If the left screw hole above the security slot is used, the security slot cannot be used. IV. Power system S3100-8TP-EI-W Ethernet switches: Rated voltage range: 100 VAC to 240 VAC, 50/60Hz Input voltage range: 90 VAC to 264 VAC, 47Hz to 63Hz V. -
Page 16: Auto-Sensing 10/100Base-Tx Ethernet Port Status Led
Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Chapter 1 Product Overview Note: Only S3100-26TP-EI-W AC-powered Ethernet switches have an RPS DC power LED. 1.3.2 Auto-Sensing 10/100BASE-TX Ethernet Port Status LED There are two port status LEDs on both sides (yellow LED on the left and green LED on the right) of each 10/100BASE-TX Ethernet port of S3100 series. - Page 17 Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Chapter 1 Product Overview Table 1-3 Description of port status LEDs on S3100 series Port status Port status LED Description mode LED The port is in the active state BLINKING and there is traffic on the port.
-
Page 18: 1000 Mbps Uplink Port Status Led
Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Chapter 1 Product Overview 1.3.3 1000 Mbps Uplink Port Status LED Table 1-4 Description of 1000 Mbps uplink port status LED on S3100 series Mark on Status Description the panel The port is connected 1000 properly. - Page 19 Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Chapter 1 Product Overview S3100-26TP- S3100-16TP- S3100-8TP-EI Model EI-W EI-W 24 x 16 x auto-sensing auto-sensing auto-sensing 10/100BASE- 10/100BASE- 10/100BASE- Number of TX Ethernet TX Ethernet TX Ethernet fixed ports port...
-
Page 20: Sfp Modules Supported By S3100 Series Ethernet Switches
Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Chapter 1 Product Overview S3100-26TP- S3100-16TP- S3100-8TP-EI Model EI-W EI-W Relative humidity (non- 10% to 90% condensing) Caution: Only the recommended 12V-RPS DC power supply can be used for S3100-26TP-EI Ethernet switches. - Page 21 1000 Mbps BIDI module SFP-GE-LX-SM1490-BIDI Note: The types of SFP modules may vary over time. Consult H3C marketing personnel or technical support personnel to obtain the latest information about SFP modules. For specifications of SFP modules, refer to H3C Low End Series Ethernet Switches Pluggable Module Manual.
-
Page 22: Chapter 2 Installation Preparation
Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Chapter 2 Installation Preparation Chapter 2 Installation Preparation 2.1 Precautions To avoid any device impairment and body injury resulting from improper use, please take the following precautions: Before cleaning the switch, disconnect the power. Do not clean the switch with wet cloth or liquid. -
Page 23: Temperature/Humidity Requirements
Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Chapter 2 Installation Preparation Enough space is reserved near the air-intake hole and the ventilation hole of the switch for heat dissipation of the switch chassis. The cabinet or the workbench takes good ventilation and heat dissipation system. -
Page 24: Cleanness Requirements
Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Chapter 2 Installation Preparation 2.2.2 Cleanness Requirements Dust is a potential hazard to the safe operation of the switch. Falling on the equipment, it may cause electrostatic adsorption, and hence result in poor contact of the metal connectors or connection points. -
Page 25: Anti-Interference Requirements
Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Chapter 2 Installation Preparation Table 2-2 Limits on harmful gas in the equipment room Max content (mg/m³) 0.006 0.05 0.01 2.2.3 Anti-interference Requirements A switch in use may be affected by the interference from outside... -
Page 26: Laser Usage Security
Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Chapter 2 Installation Preparation 2.2.4 Laser Usage Security S3100 series are category-1 laser equipment. When an optional optical interface card of the S3100 series is operating, it is prohibited to stare into the optical interface because the laser beam emitted from the optical fiber takes high energy and may hurt your retina. -
Page 27: Chapter 3 Installation
Caution: On a mounting screw of the chassis of H3C S3100 Series Ethernet Switches, there is a seal labeled with H3C. You must keep it intact before asking the agent to maintain the switch. You must get the permission of the local agent before you can open the chassis. - Page 28 Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Chapter 3 Installation Table 3-1 Installation methods for a S3100 switch Use front Use front Use front mounting mounting Model mounting ears and a ears and ears tray guide rails S3100-26TP-EI-W √...
- Page 29 Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Chapter 3 Installation When you install S3100 Series Ethernet Switches into 19-inch standard cabinets, you should select front mounting ears with a proper length (L1 as shown in Figure 3-1) according to the physical dimensions of switches.
- Page 30 Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Chapter 3 Installation Wear an ESD-preventive wrist strap to check the grounding and stability of the cabinet. Take out the screws which are packed together with the front mounting ears, and fix one end of mounting ears to the switch, as shown in Figure 3-2.
- Page 31 Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Chapter 3 Installation Front square-holed bracket Front mounting ear Front panel Front mounting Figure 3-3 Fix front mounting ears (2) III. Use front mounting ears and a tray Follow these steps to install a switch into a 19-inch standard...
- Page 32 Slotted hole 2: Used to fix the guide rail to the front bracket Figure 3-4 Appearance of a guide rail Note: Guide rails purchased from H3C apply only to standard cabinets 1,000 mm (39.4 in) deep. Use other supports to substitute for guide rails in the case of other cabinet depths.
- Page 33 Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Chapter 3 Installation Wear an ESD-preventive wrist strap to check the grounding and stability of the cabinet. Take out the screws packed together with the front mounting ears and fix one end of the front mounting ears to the switch, as shown in Figure 3-2.
- Page 34 Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Chapter 3 Installation Front panel Figure 3-6 Install front mounting ears and guide rails Fix the other end of front mounting ears to the front brackets of the cabinet with M6 screws and captive nuts and ensure that the front mounting ears and guide rails have fixed the switch in the cabinet securely, as shown in Figure 3-7.
-
Page 35: Desk Mounting
Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Chapter 3 Installation Note: No guide rails are delivered with the device. Ensure a clearance of 1U (44.45 mm, namely, 1.75 inches) between devices for the purpose of heat dissipation. 3.1.2 Desk Mounting When a 19-inch standard cabinet is not available, you can simply place the switch on a clean desk. - Page 36 Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Chapter 3 Installation Table 3-3 Models supporting wall mounting Models supporting Hole distance Subseries wall mounting (mm) S3100-8TP-EI-W S3100 Ethernet 170 mm (6.69 in.) switches S3100-16TP-EI-W I. Introduction to screw and anchor kit...
- Page 37 Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Chapter 3 Installation II. Installation procedure The wall-mounting procedure is as follows: As shown in Figure 3-10, drill two holes 5 mm across in the wall on the same horizontal line, with a distance of X=170 mm (6.69 in.).
-
Page 38: Magnet Mounting
Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Chapter 3 Installation X mm 1.5 mm(Min) Figure 3-10 Wall mounting Align the two installation holes at the bottom of the switch with these two screws to hang the switch. Caution:... - Page 39 Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Chapter 3 Installation I. Introduction to magnetic accessories A set of magnetic mounting accessories consists of one permanent magnets and one M3*6 countersunk head screws, as shown in Figure 3-11. Four sets of magnetic mounting accessories are needed for each S3100 switch.
- Page 40 Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Chapter 3 Installation Note: Remove the cushion, if any, from the dent before installation. To ensure the firmness of installation, be sure to use four permanent magnets to secure each S3100 switch.
- Page 41 Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Chapter 3 Installation Caution: Apply magnet mounting to only the above four models. Otherwise, a falloff or mis-operation may occur. Select the installation location carefully. In the case of poor surface, magnet mounting may not be reliable.
-
Page 42: Connection Of Power Cord And Grounding Cable
Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Chapter 3 Installation 3.2 Connection of Power Cord and Grounding Cable 3.2.1 Connecting AC Power Cord I. AC power socket (recommended) You are recommended to use a mono-phase three-core power socket with a neutral point or a multi-function power socket for computers. -
Page 43: Connecting Dc Power Cable
Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Chapter 3 Installation Check whether the PWR LED on the front panel of the switch is ON. If the LED is ON, it shows the power cord is properly connected. Caution: Before powering on the switch, you should properly connect the grounding cable. - Page 44 Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Chapter 3 Installation Connect one end of the grounding cable (delivered with the switch) to the grounding screw and the other end to the ground nearby. Connect the 12V-RPS DC power supply as follows: As shown in Figure 3-15, loosen the fastening screws and remove the air filter from the 12V-RPS DC power socket.
-
Page 45: Connecting Grounding Cable
Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Chapter 3 Installation Connect one end of the delivered AC power cable to the power socket of the RPS power module and the other end to the socket of an external AC power supply. - Page 46 Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Chapter 3 Installation so-called chassis ground (commonly known as PGND). This chassis ground must be securely connected to the earth so that the faradism and leakage electricity can be safely released to the earth, enhancing the EMS capability of the switch.
- Page 47 Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Chapter 3 Installation hammer an angle steel/steel pipe no shorter than 0.5 m (19.7 in.) into the earth, with the yellow-green grounding cable of the switch welded onto the angle steel/steel pipe and the jointing point being processed against erosion.
- Page 48 Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Chapter 3 Installation (1) AC power input (2) Grounding screw (3) Power transformer (4) PE cable (5) 3-core cable for AC power input (6) Ethernet switch Figure 3-19 Grounding the switch through AC PE cable For a DC-powered switch (–48 VDC), if none of the first two...
- Page 49 Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Chapter 3 Installation (1)AC/DC power cabinet (2) –48V strip (3) –48V (4) RTN strip (5) RTN (6) PGND strip (7) Grounding to the earth (8) Grounding cable (9) screw (10) Ethernet switch...
-
Page 50: Connecting Optical Fiber
Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Chapter 3 Installation 3.3 Connecting Optical Fiber Caution: After a switch starts, the optical port may emit invisible radial when there is no optical connector connected to it and the protective cap is removed from it. -
Page 51: Connection Of Console Cable
Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Chapter 3 Installation 3.4 Connection of Console Cable 3.4.1 Console Cable The console cable is an 8-core shielded cable. At one end of the cable is a crimped RJ45 connector to be connected to the console port of the switch;... -
Page 52: Connecting Console Cable
Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Chapter 3 Installation RJ-45 Signal Direction DB-9 → → 3.4.2 Connecting Console Cable Follow these steps to connect a terminal device, a PC for example, to the switch: Step 1: Connect the DB-9 female connector of the console cable to the serial port of the PC or the terminal device used to configure the switch. -
Page 53: Installation Verification
Quick Start (For Soliton) H3C S3100 Series Ethernet Switches Chapter 3 Installation Note: When connecting a PC to a powered-on switch, you are recommended to connect the DB-9 connector of the console cable to the PC before connecting the RJ45 connector to the switch. When... -
Page 54: Chapter 4 Lightning Protection Of The Switch
Quick Start (For Soliton) Chapter 4 Lightning Protection H3C S3100 Series Ethernet Switches of the Switch Chapter 4 Lightning Protection of the Switch 4.1 Installation of Lightning Arrester for AC Power (Socket Strip with Lightning Protection) Caution: Lightning arrester will not be shipped with the switch. You should purchase it by yourself if needed. - Page 55 Quick Start (For Soliton) Chapter 4 Lightning Protection H3C S3100 Series Ethernet Switches of the Switch G rounding and polarity indicator (red) : O n m eans that the lines are w rongly connected (either the ground w ire is not w ell connected, or the live and zero lines are w rongly connected).
- Page 56 Quick Start (For Soliton) Chapter 4 Lightning Protection H3C S3100 Series Ethernet Switches of the Switch Caution: Make sure that the arrester is well grounded before using the lightning arrester for power. After inserting AC power cord plug of switch into the socket of...
-
Page 57: Installation Of Lightning Arrester For Network Port
Quick Start (For Soliton) Chapter 4 Lightning Protection H3C S3100 Series Ethernet Switches of the Switch 4.2 Installation of Lightning Arrester for Network Port Note: Lightning arrester for network port is specially designed for the Ethernet port of 10/100M electrical interface (RJ-45 connector is adopted in this case). - Page 58 Quick Start (For Soliton) Chapter 4 Lightning Protection H3C S3100 Series Ethernet Switches of the Switch II. Installation procedure Step 1: Tear the protection paper at one side of the double faced adhesive tape apart from the tape, and stick the tape on the surface of the arrester.
- Page 59 Quick Start (For Soliton) Chapter 4 Lightning Protection H3C S3100 Series Ethernet Switches of the Switch Network cable indoors Network cable led into from outdoor Lightning arrester for network port Switch (attached onto the chassis) Ground wire of lightning arrester...
- Page 60 Quick Start (For Soliton) Chapter 4 Lightning Protection H3C S3100 Series Ethernet Switches of the Switch The lightning arrester for the network port is not installed completely. If the switch has more than one network ports to interconnect with other devices via cables outdoor, you should install lightning arresters for all these network ports for protection.