Charger input: 120 V AC, 60 Hz Charger output: 9 V DC, 400 mA Weight: 2 lb 2 oz (0.97 kg) NEED ASSISTANCE? Call us on our toll-free Customer Support Line: 1-800-689-9928 Imported by Mastercraft Canada Toronto, Canada M4S 2B8...
GENERAL SAFETY WARNINGS CAUTION: Before using this tool or any of its accessories, read this manual and follow all Safety Rules and Operating Instructions. This instruction manual includes the following: General Safety Rules Specific Safety Rules and Symbols ...
GENERAL SAFETY WARNINGS WEAR A DUST MASK THAT IS DESIGNED TO BE USED WHEN OPERATING A POWER TOOL IN A DUSTY ENVIRONMENT. WARNING: Dust that is created by power sanding, sawing, grinding, drilling, and other construction activities may contain chemicals that are known to cause cancer, birth defects, or other genetic abnormalities.
POWER TOOL SAFETY GENERAL SAFETY RULES Avoid contact between the operator's body and grounded surfaces such as pipes, WARNING: Read and understand radiators, ranges, and refrigerators. There all instructions. Failure to follow all is an increased risk of electric shock if the instructions listed below may result in operator's body is grounded.
POWER TOOL SAFETY PERSONAL SAFETY – cont’d Do not use a power tool if it cannot be turned ON or OFF using the power switch. Avoid accidental start-ups. Verify that the A tool that cannot be controlled using the switch is in the OFF position before switch is dangerous, and must be repaired.
POWER TOOL SAFETY SERVICE – cont’d Always check to make sure the area where screws are being driven or where holes When servicing a tool, use only identical are being drilled does not have any hidden wiring. Contact with a “live” wire will make replacement parts.
SPECIFIC SAFETY RULES Do not use worn or damaged screwdriver Do not use the charger in wet or damp or drill bits. Worn or damaged screwdriver conditions. It is intended for indoor use bits will not drive the screw properly and only.
SYMBOLS WARNING: Some of the following symbols may appear on the cordless screwdriver. Study these symbols and learn their meaning. Proper interpretation of these symbols will allow for more efficient and safer operation of this tool. Volts Direct current Amperes No load speed Hertz Alternating or direct...
KNOW YOUR CORDLESS SCREWDRIVER Quick release Magnetic tray collar Collet Left/right switch Variable speed trigger switch Battery status LED switch Battery & charging status LED’s worklight Charger plug LED light receptacle switch Charging stand Accessory bit storage Accessory bit storage drawer...
ACCESSORIES AND CONTENTS AVAILABLE ACCESSORIES CORDLESS SCREWDRIVER COMPONENTS WARNING: Use only accessories DESCRIPTION that are recommended for this cordless Cordless screwdriver. Follow the instructions screwdriver that accompany the accessories. The Charging stand use of any other accessories may result Charger in injury to the operator or damage to Screwdriver bit the cordless screwdriver.
ASSEMBLY AND OPERATING CHARGING THE BATTERY Place the cordless screwdriver and the charging stand near a 120 V, 60 Hz electrical outlet. Insert the small battery charger plug (1) into the receptacle in the rear of the charging stand (2) (Fig. 1). Plug the battery charger (3) into a Fig.
ASSEMBLY AND OPERATING BATTERY CHARGE STATUS The battery status can be checked at any time by pressing and releasing the battery status button (2) located in the base of the tool immediately above the LED status indicators (1) (Fig. 4). The amount of charge remaining in the battery will be indicated by the LED’s.
ASSEMBLY AND OPERATING BATTERY CHARGING STATUS When the tool is in the charging stand with the charger plugged into the power source, the battery will be in the process of being Battery 0 to 1/3 charged. Similar to the battery charge charged status, the LED’s will indicate the status of the charging process.
ASSEMBLY AND OPERATING INSTALLING SCREWDRIVER BITS WARNING: Never hold the cordless screwdriver with your fingers near the switch while changing screwdriver bits. Accidentally touching the switch may start the tool and possibly cause an injury. Push the quick release collar (1) back toward the rear of the tool (Fig.
ASSEMBLY AND OPERATING INSTALLING SCREWDRIVER BITS – cont’d NOTE: Make sure the screwdriver bit is fully inserted into the magnetic bit holder until it is held in place by the magnet. FORWARD/REVERSE SWITCH The forward/reverse switch (1) is conveniently mounted above the trigger switch (Fig.
ASSEMBLY AND OPERATING VARIABLE-SPEED TRIGGER SWITCH – cont’d NOTE: Drilling at a slow speed for an extended period of time may cause the cordless screwdriver motor or the battery to overheat. If the cordless screwdriver gets hot, stop drilling and allow it to cool for at least 15 minutes.
ASSEMBLY AND OPERATING SCREWDRIVER WORKLIGHT The cordless screwdriver is equipped with an LED worklight (1) (Fig. 16). To turn the worklight ON, press the worklight switch button (2) once. To turn the worklight OFF, press the worklight switch again. NOTE: The worklight will remain ON until it is manually turned OFF.
ASSEMBLY AND OPERATING PREPARING SCREW HOLES It is important to prepare screw holes before attempting to fasten two pieces of wood together. Proper preparation will make screws drive easier and prevent misaligned components, stripped screw heads, splitting and separating of wood components.
ASSEMBLY AND OPERATING DRIVING SCREWS When driving screws, care must be taken to use a bit that correctly fits the head of the screw being driven. Make sure you use the largest bit size that will properly fit into the head of the screw. The bits must also be in good condition and not worn so they will drive screws without slipping out of the screw head.
ASSEMBLY AND OPERATING ASSEMBLY AND OPERATING DRILLING When drilling into smooth, hard surfaces such as metal, use a centre punch to mark the desired hole location. This will prevent the drill bit from slipping off centre as the hole is started. The workpiece to be drilled should be secured in a vice or with clamps to keep it from turning as the drill bit rotates...
MAINTENANCE GENERAL LITHIUM-ION BATTERY PERFORMANCE WARNING: When servicing this tool, use only identical replacement Lithium-ion rechargeable batteries parts. The use of any other part may generally provide superior performance to create a hazard or cause product nickel-cadmium batteries when used in damage.
MAINTENANCE BATTERY PACK REMOVAL AND PREPARATION FOR RECYCLING To preserve our natural resources, please recycle or dispose of batteries properly. The batteries supplied with this tool may contain chemicals and metals that are harmful to the environment. Never dispose of rechargeable batteries in your normal household garbage or in landfill sites because they will add to the pollution of the environment.
PARTS LIST ® WARNING: When servicing, use only Mastercraft replacement parts. The use of any other parts may create a safety hazard or cause damage to the cordless screwdriver. Any attempt to repair or replace electrical parts on this cordless screwdriver may create a safety hazard unless repairs are performed by a qualified technician.
Page 27
PARTS LIST Key # Part # Part Name Quantity 6902034909 Roller pin 5100450101 Planetary carrier 5100210101 Planetary gear 5100460101 Planetary carrier 5100480101 Planetary gear 5400530101 Big washer 6511300812 Screw M3x8 4400430101 Motor flange 6411291222 Tapping screw ST2.9x12 5100410101 Motor gear 2500220101 Motor 5201170101...
3-Year Limited Warranty This Mastercraft product is guaranteed for a period of 3 years from the date of original retail purchase against defects in workmanship and materials, except for the following components: Component A: Batteries, chargers and carrying cases, which are guaranteed for a period of 2 years from the date of original retail purchase against defects in workmanship and materials;...
Mastercraft is a superior line of products selected for their workmanship and materials. These products are designed to meet rigorous quality and performance standards, and are approved by our Quality Assurance laboratory.
Need help?
Do you have a question about the 054-2822-4 and is the answer not in the manual?
Questions and answers