Advertisement
Quick Links
Thank you for choosing eLock.
CompX eLock
is a highly engineered lock with a motor-driven latch. Its uncompromising lock
®
control electronics include a non-volatile memory that stores 250 user / supervisor codes and
audit trail. With optional LockView
attempts. Programming is simple with numeric keypad or Windows
NUMERIC
KEyPAD
Quick Programming Guide
1. GETTING STARTED:
a. The unit is shipped with no user / supervisor codes
b. Press and hold
c. Input the new PIN (4 digit min) and press
d. This PIN / Card is now a supervisor in slot #001
2. ADD A USER:
a. Input a valid supervisor PIN and press
b. Press and hold
c. Input the new user PIN (4 digit min) and press
3. ADD A SUPERVISOR:
a. Input a valid supervisor PIN and press
b. Press and hold
c. Press and hold
d. Input new supervisor PIN (4 digit min) and press
4. DELETE A USER OR SUPERVISOR:
a. Input a valid supervisor PIN and press
b. Press and hold
c. Input the PIN to be deleted and press
5. ADD A USER WITH A SPECIFIC SLOT ASSIGNMENT:
a. Input a valid supervisor PIN and press
b. Press and hold
c. Enter slot number that will be assigned to user and press
(example: to program slot 6 type 006
d. Input the new user PIN (4 digit min) and press
6. DELETE A USER WITH A SPECIFIC SLOT ASSIGNMENT:
a. Input a valid supervisor PIN and press
b. Press and hold
c. Enter slot number to be cleared and press
d. Enter slot number to be cleared again and press
audit trail software, CompX eLock
®
MAGSTRIPE
CARD
until the beeping stops
or present new card
or present valid supervisor card
until beeping stops
or present valid supervisor card
until beeping stops
again until beeping stops
or present valid supervisor card
until beeping stops
or present existing card to be deleted
or present valid supervisor card
until beeping stops
)
or present valid supervisor card
until beeping stops
(example: to clear slot 6 type 006
MAGSTRIPE / KEyPAD
DUAL SySTEM
or present new card
or present NEW supervisor card
or present NEW card
(example: to clear slot 6 type 006
remembers 1500 access
®
based LockView
TM
PROx READER / KEyPAD
DUAL SySTEM
PROx
READER
See programming
guide included
with optional
LockView
software for
programming
instructions.
)
)
software.
®
®
advanced
1
1
Advertisement
Related Manuals for COMPX elock
Summary of Contents for COMPX elock
- Page 1 Thank you for choosing eLock. CompX eLock is a highly engineered lock with a motor-driven latch. Its uncompromising lock ® control electronics include a non-volatile memory that stores 250 user / supervisor codes and audit trail. With optional LockView audit trail software, CompX eLock remembers 1500 access ®...
- Page 2 Accessories AC A DAPTER ATCH PLITTER Part Numbers: EL-2004-9VWB (for running up to 2 latches) (for use with the CompX eLock kit) Part Number: EL-2004-acWB EL-2004-LS (for use with 12V electric strikes) OTORIzED RIVER ATCH* (Torx head bit also available)
- Page 3 TEMPLaTE on oPPoSiTE PagE...
- Page 4 CompX eLock ® Surface Mounting Use the diagrams below as a template for holes to be drilled and for mounting your CompX eLock ® outside Put this template on the of the cabinet door where the eLock will go, and you can drill right through Mount with 2 shorter, steel colored screws.
- Page 5 Use the diagrams below as a template for holes to be drilled and for mounting your CompX eLock latch. Put this template on the inside of the cabinet door where the latch ® will go, and you can drill right through it to mount your CompX eLock latch. ® 1”...
- Page 6 TEMPLaTE on oPPoSiTE PagE...
- Page 7 These stickers are included with each CompX eLock® unit. Please review the information and keep the stickers in a safe location as they may be needed to reset or identify a specific eLock unit. The codes shown here are not real codes.
- Page 8 CompX eLock ® Warranty Card Affix one copy of sticker #3 (see page 7) to the CompX eLock® registration card Sticker and return to CompX Fort at address shown on the registration card. NoTe: Don't forget to fill out and...
Need help?
Do you have a question about the elock and is the answer not in the manual?
Questions and answers