Table of Contents
Advertisement
Appendix
Installation Location
and Handling
This section describes precautions for
installation location and handling. We
recommend that you read this section
prior to using this machine.
Installation Precautions
Avoid Installing the Machine in the
Following Locations
Avoid locations subject to temperature
and humidity extremes, whether low
or high. For example, avoid installing the
machine near water faucets, hot water
heaters, humidifiers, air conditioners,
heaters, or stoves.
Avoid installing the machine in direct
sunlight. If this is unavoidable, use curtains
to shade the machine. Be sure that the
curtains do not block the machine's
ventilation slots or louvers, or interfere
with the electrical cord or power supply.
Avoid locations where a considerable
amount of dust accumulates./Avoid
locations where ammonia gas is
emitted./Avoid locations near volatile or
flammable materials, such as alcohol or
paint thinner.
Avoid poorly ventilated locations. This
machine generates a slight amount of
ozone etc. during normal use. Although
sensitivity to ozone etc. may vary, this
amount is not harmful. Ozone etc. may be
more noticeable during extended use or
long production runs, especially in poorly
ventilated rooms. It is recommended that
the room be appropriately ventilated,
sufficient to maintain a comfortable
working environment, in areas of machine
operation. In addition, do not install this
machine where it exhausts directly onto a
person.
Avoid locations that are subject to
vibration./ Avoid exposing the machine
to rapid changes in temperature. If the
room in which the machine is installed is
cold but rapidly heated, water droplets
(condensation) may form inside the
machine. This may result in a noticeable
degradation in the quality of the copied
image, the inability to properly scan an
original, or the copies having no printed
image at all.
Avoid installing the machine near
computers or other precision electronic
equipment. Electrical interference and
vibrations generated by the machine
while printing can adversely affect the
operation of such equipment.
Avoid installing the machine near
televisions, radios, or similar electronic
equipment. The machine might interfere
with sound and picture signal reception.
34
Insert the power plug into a dedicated
power outlet, and maintain as much
space as possible between the machine
and other electronic equipment.
Connecting the Telephone Line
This machine conforms to a analog
telephone line standard. The machine
can be connected to the public switched
telephone network (PSTN) only. If
you connect the machine to a digital
telephone line or a dedicated telephone
line, it might impede proper operation
of the machine and could be the cause
of damage. Make sure to confirm a type
of telephone line before connecting the
machine. Contact your optical fiber line or
IP telephone line service providers if you
want to connect the machine to those
telephone lines.
Contact an authorized Canon dealer
if communication is unavailable.
Depending on your locale or your
telephone connection, you may be unable
to perform data communication. In this
case, contact your local authorized Canon
dealer.
When using wireless LAN
Install the machine at a distance of
•
164 ft. (50 m) or less from the wireless
LAN router.
As far as possible, install in a location
•
where communication is not blocked
by intervening objects. The signal may
be degraded when passing through
walls or floors.
•
Keep the machine as far as possible
from digital cordless phones,
microwave ovens, or other equipment
that emits radio waves.
Avoid installing the machine at high
altitudes of about 3,000 metres above
sea level, or higher. Machines with a hard
disk may not operate properly when used
at high altitudes of about 3,000 metres
above sea level, or higher.
Select a Safe Power Supply
•
Plug the machine into a 120 V AC
outlet.
•
Make sure that the power supply for
the machine is safe, and has a steady
voltage.
•
Do not connect other electrical
equipment to the same power outlet
to which the machine is connected.
•
Do not connect the power cord to
a multiplug power strip, as this may
cause a fire or electrical shock.
•
The power cord may become
damaged if it is stepped on, affixed
with staples, or if heavy objects are
placed on it. Continued use of a
damaged power cord can lead to an
accident, such as a fire or electrical
shock.
The power cord should not be taut, as
•
this may lead to a loose connection
and cause overheating, which could
result in a fire.
If excessive stress is applied to the
•
connection part of the power cord,
it may damage the power cord or
the wires inside the machine may
disconnect. This could result in a fire.
Avoid the following situations:
–
Connecting and disconnecting the
power cord frequently.
–
Tripping over the power cord.
–
The power cord is bent near the
connection part, and continuous stress
is being applied to the power outlet or
the connection part.
–
Applying excessive force on the power
plug.
Moving the Machine
If you intend to move the machine, even
to a location on the same floor of your
building, contact your local authorized
Canon dealer beforehand. Do not
attempt to move the machine yourself.
Provide Adequate Installation Space
Provide enough space on each side
•
of the machine for unrestricted
operation.
•
For the installation space requirements,
see page 35.
Hide quick links:
Advertisement
Table of Contents
