EverFocus ed610 Operation Instructions Manual
  1. Manuals
  2. Brands
  3. EverFocus Manuals
  4. Security Camera
  5. ED610
  6. Operation instructions manual

EverFocus ed610 Operation Instructions Manual

1/3” ccd color day/night plus wide dynamic range outdoor vandal dome camera
Hide thumbs Also See for ed610:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Quick Reference Manual
Please read this manual first for correct installation and operation. This manual should be retained for future reference.
The information in this manual was current when published. The manufacturer reserves the right to revise and improve
its products. All specifications are therefore subject to change without notice.
PRECAUTIONS
1.
Do not install the camera near electric or magnetic fields.
Install the camera away from TV/radio transmitters, magnets, electric motors, transformers and audio speakers
since the electromagnetic fields generated from these devices may distort the video image.
2.
Never disassemble the camera beyond the recommendations in this manual nor introduce materials
other than those recommended herein.
Improper disassembly or introduction of corrosive materials may result in equipment failure or other damage.
3.
Try and avoid facing the camera toward the sun.
In some circumstances, direct sunlight or may cause permanent damage to the sensor and/or internal circuits.
4.
Keep the power cord away from water and other liquids and never touch the power cord with wet hands.
Touching a wet power cord with hands or touching the power cord with wet hands may result in electric shock.
5.
Never install the camera in areas exposed to oil, gas or solvents.
Oil, gas or solvents may result in equipment failure, electric shock or, in extreme cases, fire.
6.
Cleaning
Do not touch the surface of the sensor directly with the hands. Use a damp soft cloth to remove any dirt from the
camera body. Use lens tissue or a cotton tipped applicator and ethanol to clean the sensor and the camera lens.
Please do not use complex solvents, corrosive or abrasive agents for cleaning.
7.
Do not operate the camera beyond the specified temperature, humidity or power source ratings.
Use the camera at temperatures within -10℃ ~ 50℃ (14℉~122℉) and in an IP66 complaint environment; this
device is not rated as submersible. The input power source is 12VDC/24VAC.
1/3" CCD Color Day/Night
plus Wide Dynamic Range
Outdoor Vandal Dome Camera
Operation Instructions
Model No. ED610

Advertisement

Table of Contents
loading

Related Manuals for EverFocus ed610

Summary of Contents for EverFocus ed610

  • Page 1 Outdoor Vandal Dome Camera Operation Instructions Model No. ED610 Please read this manual first for correct installation and operation. This manual should be retained for future reference. The information in this manual was current when published. The manufacturer reserves the right to revise and improve its products.

  • Page 2: Table Of Contents

    2.2.4 Close the Camera Cover (after installation is complete) ................16 3. OSD MENU & CONFIGURATION....................18 3.1 Access the user setup menu screen....................... 18 3.2 ED610 Menu Tree............................19 3.3 LENS................................22 3.4 EXPOSURE ..............................22 3.4.1 SHUTTER ..............................22...
  • Page 3 3.4.2 AGC (Auto Gain Control)..........................22 3.4.3 SENSE-UP............................... 22 3.4.4 BLC ................................. 23 3.4.5 HSBLC..............................24 3.4.6 D-WDR ..............................24 3.4.7 Return..............................24 3.5 WHITE BALANCE CONTROL........................25 3.6 DAY NIGHT..............................25 3.7 3DNR ................................. 26 3.8 SPECIAL ..............................26 3.8.1 CAM TITLE...............................

  • Page 4: Product Overview

    Amazing color low light sensitivity of .05 lux before the added benefits of digital signal processing technology, delivered by a 1/3” Sony Super HAD II sensor, is just the beginning with the new EverFocus ED610. Get color without compromise: 560TVL resolution, your choice of full motion color or true day/night images in low light without ghosting, plus 120dB Digital Wide Dynamic Range to handle the most challenging of bright or unbalanced scene lighting conditions.
  • Page 5 Please Note: If an item appears to have been damaged in shipment, replace it properly in its carton and notify the shipper. If any items are missing, notify your EverFocus Electronics Corp. Sales Representative or Customer Service. The shipping carton is the safest container in which the unit may be transported.

  • Page 6: Specifications

    1.3 Specifications Items Parameter Pickup Device 1/3" SONY Super HAD II CCD Video Format NTSC or PAL Scanning System NTSC:525 TVL, 60 fields/sec PAL:625 TVL, 50 fields/sec Picture Elements 768 x 494(NTSC); 752 x 582 (PAL) Horizontal Resolution 560 TVL Sensitivity 0.05Lux/F=1.2(AGC ON);...

  • Page 7: Dimensions

    1.4 Dimensions 123mm x 107.8mm ; 4.8” x 4.2” Ø 5.143mm//0.2” Ø 94.7mm/3.78” - 6 -...

  • Page 8: Camera Component Description

    1.5 Camera Component Description Exterior view Base Outer Cover ring Rotatable cover Interior view OSD joystick Power board - 7 -...

  • Page 9: Front And Back Panel Layout

    1.6 Front and Back Panel Layout Front Panel Layout: Back Panel Layout: - 8 -...

  • Page 10: Related Products

    ), press the stick again to display the sub- menu. 1.7 Related Products In addition, you may order the following EverFocus products which are recommended for use with the camera to achieve the best performance: L Type Bracket: BA-EDMS EN220 5.6 inch LCD Test Monitor...

  • Page 11: Installation

    2. INSTALLATION This chapter will describe, in general terms, how to install the ED610 camera. STEPS: 2.1. Mounting Camera: 1. Drill the Holes. See 2.1.1 2. Mounting: See 2.1.2 2.2. Adjusting Camera: 1. Adjust the camera position. See 2.2.1 2. Adjusting Zoom and Focus See 2.2.2 3.

  • Page 12: Mounting

    Wire outlet hole for Surface mounting Power/Video Cable Screw A,B,C Camera base 2.1.2 Mounting 1. Take off camera’s cover by rotating the cover counter clockwise. Loose outer cover ring first Take off camera’s cover - 11 -...
  • Page 13 2. Pull the cables to be connected to the power and video cables from the ceiling or wall. Video output Power input 3. Fix the camera base to ceiling or wall by using 3 screws and washers. The washers are used to create the IP66 seal and must be used.

  • Page 14: Adjusting Camera

    Wall Mount: 2.2 Adjusting Camera 2.2.1 Adjusting Camera Position Adjust the camera to best angle for viewing. When you install on the ceiling, change angle of view by turning these joints. Module can be adjusted up and down - 13 -...

  • Page 15: Adjusting Zoom And Focus

    2.2.2 Adjusting Zoom and Focus It is highly recommended to use an EverFocus Test Monitor to set up the camera. Find the Video test connection on the back of the camera module. Connect using the video cable included in the package.
  • Page 16 Step 2 Open the dome cover and place the Focus aiding lens cap on the lens, making sure that the cap’s notch is resting on the zoom knob. Step 3 With cap on, adjust the focus and zoom rings by loosening the knobs and turning the rings until subject is in focus.

  • Page 17: Camera Setting

    Please refer to Chapter 3 OSD Menu & Configuration, to get more details about OSD menu usage. 2.2.4 Close the Camera Cover (after installation is complete) The ED610 is specially designed with one inner cover and one outer cover ring for water-proofing and ease of installation. Please follow these instructions for closing the camera cover.
  • Page 18 Correct Wrong (not aligned) 3. If the lens is not aligned with the window, loosen the outer cover, adjust the inner cover so that the lens aimed exactly at the window. Slightly adjust the cover 4. Tighten the outer cover ring until it is firmly secured. Turn the external ring - 17 -...

  • Page 19: Osd Menu & Configuration

    3. OSD MENU & CONFIGURATION This chapter introduces how to configure the camera OSD menu. Joystick 3.1 Access the user setup menu screen Press inward on the end of the joystick The menu screen will appear on the monitor. Navigating with the joystick Angle the joystick to move the cursor up or down.

  • Page 20: Ed610 Menu Tree

    3.2 ED610 Menu Tree - 19 -...
  • Page 21 - 20 -...
  • Page 22 - 21 -...

  • Page 23: Lens

    3.3 LENS 1. When the SETUP menu is displayed on the screen, please direct the arrow to point to “LENS” by moving the joystick UP and DOWN. NOTE: The brightness of the screen can be adjusted in the BRIGHTNESS sub menu. The level can be adjusted from 0 to 100.

  • Page 24: Blc

    NOTES: ○ The maximum amplification in low light level situations can be adjusted by pressing the SETUP button in “AUTO” mode. This sets an upper limit on the ‘boost’. ○ The image becomes brighter when the setting increases; however, the after image increases as well.

  • Page 25: Hsblc

    3.4.5 HSBLC HSBLC Highlight Suppression BLC is used to reduce the brightness of light sources in a specific area. It is activated only in a low illumination environment to minimize the effects of glare from bright lights such as spotlights, street lights or headlights in the field of view. Where ‘traditional’ BLC can increase the exposure of a dark area surrounded by a brighter area, HSBLC can decrease the exposure of bright areas surrounded by darker areas.

  • Page 26: White Balance Control

    3.5 WHITE BALANCE CONTROL The screen color can be adjusted by using the WHITE BALANCE function. 1. Please direct the arrow to point to “WHITE BAL” by moving the joystick UP and DOWN. 2. Please select the mode you would like to operate by moving the joystick LEFT or RIGHT. Please select one of the 6 modes below: ATW (Auto Tracking White Balance): This mode can be used within the color temperature range from 5,500°K to 6,000°K (eg,...

  • Page 27: 3Dnr

    COLOR: The picture is always displayed in color, even at low light levels. AUTO: The picture switches to color in a normal (bright) environment and switches to B/W when the ambient illumination is low. The switching point is determined by the AGC level. Note: AGC selection must be set as middle or high in order to employ the auto switching function.

  • Page 28: D-Effect

    6) If you would like to cancel the ID entered, please move the cursor to “CLR”, press in on the joystick, and all the letters entered will be deleted. 7) Select “END” and press in on the joystick to complete the ID input. 3.8.2 D-EFFECT 3.8.2.1 FREEZE (Note that practical application of this feature requires direct access to the camera menu in real...

  • Page 29: Motion

    D-Zoom: Select digital zoom from X1.0 up to X32. To control the portion of the magnified image in view (0 is the center of the image): Pan: Select pan digital zoom from -100 to 100. Tilt: Select tilt digital zoom from -100 to 100. Return: Select “RET”...

  • Page 30: Privacy

    L/L: External line-lock synchronization 3.8.6 LANGUAGE Select OSD language. ED610 camera supports multiple languages. 3.8.7 RETURN Select “RET” to save all settings in SPECIAL menu and returns to the previous menu. Select “END” to save all the menu settings and exit from OSD menu.

  • Page 31: Blue

    3.9.2 BLUE Adjust image’s blue level. The available range of level is 0~100. 3.9.3 RED Adjust image’s red level. The available range of level is 0~100. 3.9.4 RETURN Select “RET” to save all settings in ADJUST menu and returns to the previous menu. Select “END”...
  • Page 32 1801 Highland Ave. Unit A 415 Oser Ave Unit S Duarte, CA 91010 ,U.S.A Hauppauge, NY 11788 Tel: +1-626-844-8888 Sales: +1-631-436-5070 Fax: +1-626-844-8838 Fax: +1-631-436-5027 Ihr EverFocus Produkt wurde entwickelt und Your EverFocus product designed hergestellt qualitativ hochwertigen manufactured with high quality materials and Materialien und Komponenten, die recycelt und components which can be recycled and reused.

Table of Contents