Wavion WBS-2400 Installation Manual
Outdoor wi-fi sector
Hide thumbs
Also See for WBS-2400:
- User manual (116 pages) ,
- Installation manual (74 pages) ,
- User manual (108 pages)
Related Manuals for Wavion WBS-2400
Summary of Contents for Wavion WBS-2400
- Page 1 WBS-2400 & WBS-5800 Outdoor Wi-Fi Sector Base Station Installation Guide Rev. 3 February 2009...
- Page 2 Note: To better reflect the value of Wavion products we are changing the name of our product family from Access Points (AP) to Wireless Base Stations (WBS), consequently the existing WS- 410 product name will be changed to Wavion WBS-2400.
- Page 3 Warning Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
-
Page 4: Table Of Contents
C h a p t e r 2 Package Content ................ 8 C h a p t e r 3 Installing the Wavion WBS-2400/5800 Sector Base Station .. 10 C h a p t e r 4 Important Safety Instructions..............11 Preparing for Installation................. -
Page 5: About This Guide
Chapter 1 About This Guide Preface This guide details the Wavion WBS-2400/5800 Sector installation procedures. The intended audience of this document is trained technical professionals. Conventions The exclamation point within a triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. -
Page 6: Contacting Technical Support
About This Guide Contacting Technical Support For technical support, contact Wavion using these methods: Wavion Technical Support Wavion 6 Hayetzira Street, Address: PO BOX 580 Yoqneam Illit, 20692 Israel Telephone: +972-4-9097300 Fax: +972-4-9097322 support@wavionnetworks.com Email: www.wavionnetworks.com Web: Wavion Networks... -
Page 7: Introduction
Introduction WBS-2400/5800 Sector a high capacity, IP services oriented Broadband Wireless access system. WBS-2400/5800 Sector is a new category of Broadband Wireless Base Station designed from the ground up for metro-Wi-Fi deployments. The system employs wireless packet switched data technology to support high-speed IP services including fast Internet and Virtual Private Networks. -
Page 8: Package Content
(reset button and Link LED). Using cross cable might cause turn Link led to “ON” permanently and also may be the cause software reset. DATA cable connecting the injector to the network can be cross cable as well. Wavion Networks... - Page 9 Failure to do so may void the WBS-2400/5800 product warranty and may expose the end user or Service Provider to legal and financial liabilities.
-
Page 10: Installing The Wavion Wbs-2400/5800 Sector Base Station
Chapter 4 Installing the Wavion WBS-2400/5800 Sector Base Station This guide explains how to safely install the Wavion WBS-2400/5800 Sector Base Station. The following topics are covered in this chapter: Important Safety Instructions • Preparing for Installation • Mounting Strategies •... -
Page 11: Important Safety Instructions
Warning: Risk of personal injury or death when installing this device! There is a risk of personal injury or death if the WBS-2400/5800 antennas come near electric power lines. Carefully read and follow all instructions in this manual. By nature of the installation, you may be exposed to hazardous environments and high voltage. -
Page 12: Preparing For Installation
Caution The WBS-2400/5800must be installed only with the equipped antennas. Caution A minimum distance of 40cm from the WBS-2400/5800X's antenna should be kept when the system is operated. Caution Read and save these instructions. Heed all warnings. Follow all instructions... -
Page 13: Choosing A Location
Choosing a Location To ensure the optimal performance select the locations for the equipment using the following guidelines: The antenna (integrated on the front panel of the outdoor unit) should provide a direct, or near line of sight, with the sector location that need to be covered. The antenna should be aligned to face the CPEs that aim to be in service, higher the placement of the antenna, the better the achievable link quality (but not in all cases). -
Page 14: Mounting Strategies
Wavion outdoor unit WBS-2400/5800 Sector should be mounted horizontal pole only the antennas pointing vertically and clear of obstruction. It is recommended to attach ground and data cables to the WBS-2400/5800 Sector prior to mounting. Before mounting the WBS-2400/5800 Sector, read the wiring instructions in Grounding the Wavion WBS-2400/5800 Connecting Power and Data. -
Page 15: Mounting On A Pole/Streetlight
Figure 4.2 Using Special Hose Clamps & Screwing the Clamps Mounting on a Pole/Streetlight WBS-2400/5800 Sector can be mounted on a pole, tower, or streetlight. It is recommended to mount the WBS-2400/5800 Sector on aluminum or galvanized steel structures. Note... - Page 16 To mount the Wavion WBS-2400/5800 on a metal/wood/streetlight pole: 1. Choose a mounting location. You can attach the WBS-2400/5800 Sector outdoor unit to any pole or pipe with diameter of 3-10 inches. Wooden poles of larger diameter require different types of clamps (any streetlight arm with diameter of 3 to 10 inches will fit for this installation).
- Page 17 Note : The WBS-2400/5800 unit must be parallel to the ground. The unit can be rotated to obtain the correct position. Note Installations on large wooden poles require band clamps such as those supplied by Panduit, www.panduit.com. Such a product is listed as "Metal, Locking Tie Extra Heavy Duty 304 Stainless Steel".
-
Page 18: Grounding The Data Protection Device
To ground the Wavion WBS-2400/5800: The Grounding screw is located on the side panel of the outdoor unit. To connect the grounding cable: Connect one end of a grounding cable to the grounding terminal and tighten the grounding screw firmly. - Page 19 Figure 4.6 Grounding indoor injector by Network Protection Unit Figure 4.7 Grounding injector that located outdoor by Network Protection Unit Installation Guide...
-
Page 20: Connecting Power And Data
Make sure you have completed grounding before you connect power to the WBS-2400/5800X. The Wavion WBS-2400/5800 is equipped with two RJ45 connectors. The right hand port named "TEST" is for engineering use only (!) and has to be sealed with the sealing rubber. - Page 21 Wavion WBS-2400/5800 through the lightning protection device. See "Grounding the Data protection device" section for connection diagram. 3. Connect one end of the Category 5 cable to the "RADIO" port of the Wavion POE injector. 4. Connect the other cable end to ETH port on the WBS-2400/5800. Use a shielded RJ45 8-pin modular plug to terminate the cables at the desired lengths.
- Page 22 Figure 4.9 Sealing rubber 7. Remove the strip nylon cover Wavion Networks...
- Page 23 (attached to the product) Splicing Tape from 3M to ensure IP-67 compliant protection against dust and water Figure 4.11 Weatherproof Stripe sealing 9. Connect the data cable from the network to "Ethernet" port of POE injector. 10. Connect POE injector to AC power source to power WBS-2400/5800 unit. Installation Guide...
-
Page 24: Safety Information For The Wavion Wbs-2400/5800
FCC recommended limits. Follow these guidelines to ensure safe operation of the Wavion WBS-2400/5800X: • Do not touch or move the antennas while the unit is transmitting or receiving. -
Page 25: Service Instructions
Service Instructions The Wavion WBS-2400/5800 contains no user serviceable parts inside. Installation Guide... -
Page 26: Product Specification Wbs-2400 Sector
Chapter 5 Product Specification WBS-2400 Sector The tables in this chapter contain specifications for the Wavion WBS-2400. Wireless Specifications compliant IEEE 802.11b/g Frequency band 2.4 - 2.483 GHz • 802.11b: DSSS (DBPSK, DQPSK, CCK) Modulation • 802.11g: OFDM (64QAM, 16QAM, QPSK,... - Page 27 HTTPS for web-based management tools Management Specifications Networking and QoS Specifications Web based configuration and management too Full 802.11b/g client compatibility SNMPv2 with standard and Wavion MIB support 16 VLANs Configuration save and restore 16 SSIDs Network and client statistics...
- Page 28 • Weight: 4.6 Kg Power • Specifications Power Input • 55VDC, supplied over Ethernet from Wavion injector. • Power from Wavion Injector max.0.8A @ 55VDC Input Power • Input power consumption for units is max. Consumption 0.45A@55V ;...
- Page 29 Environmental Specifications -40°C to +55°C (without Sun Shield) Operating Temperature Range -40°C to +60°C (with Sun Shield) Storage Temperature Range -45°C to +85°C Weather Rating IP67 Wind Survivability 165 mph Salt and Fog Rust Resistance MIL-STD-810F 509.4 Shock and Vibration ESTI 300-192-4 spec T41.E Transportation ISTA2A...
-
Page 30: Antenna 2.4Ghz Specifications And Patterns
Chapter 6 Antenna 2.4GHz Specifications and Patterns The chapter describes antenna specifications and patterns for the antennas supplied with the Wavion WBS-2400. MT-343037/CV 2.4GHz Sector Antenna 2.4GHz Flat Panel Base Station Antenna Wavion Networks... - Page 31 6 W (max) Lighting protection DC Grounded Mechanical Dimensions (Lx W x D) 346.5 x 344.7x 44 mm (max) The antenna contour per Wavion enclosure Weight 1.2 kg (max), 1.0 kg design goal RF Connector 3x MCX female Radome Plastic color- RAL 9002...
- Page 32 IEC 68-2-1 72 h -45° C High Temperature IEC 68-2-2 72 h +90° C Temp. Cycling IEC 68-2-14 -45° C +90° C 3 Cycles Vibration IEC 60721-3-4 Random min/axis Shock Mechanical IEC 60721-3-4 Humidity ETSI EN300-2-4 144 h T4.1E Wavion Networks...
-
Page 33: Product Specification Wbs-5800
Chapter 7 Product Specification WBS-5800 The tables in this chapter contain specifications for the Wavion WBS-5800. Wireless Specifications compliant IEEE 802.11b/g Frequency band 5.725–5.850 GHz Modulation 802.11a: OFDM (64QAM, 16QAM, QPSK, BPSK) Max. power per antenna: 19dBm (FCC version -... - Page 34 Management Specifications Web based configuration and management too SNMPv2 with standard and Wavion MIB support Configuration save and restore Network and client statistics Security Specifications Packet filtering via layer 2 & 3 WEP (64 bit or 128 bit) WPA: Encryption: WEP or TKIP Authentication: Pre-Shared Key or 802.1x with RADIUS Server (EAP-TLS, PEAP, EAP-TTLS)
- Page 35 • Weight: 4.6 Kg Power • Specifications Power Input • 55VDC, supplied over Ethernet from Wavion injector. • Power from Wavion Injector max.0.8A @ 55VDC Input Power • Input power consumption for units is max. Consumption 0.45A@55V ;...
- Page 36 Approvals FCC CFR 47 part 15, Sub Part C TUVus EN 60950-1:2001+A11:2004 IEC 60950-1:2001 Safety First Edition Information Technology equipment – Safety – Part 1 FCC CFR 47 Part 15, Sub Part B, Class B (USA) Wavion Networks...
- Page 37 6 W (max) Lighting protection DC Grounded Mechanical Dimensions (Lx W x D) 346.5 x 344.7x 44 mm (max) The antenna contour per Wavion enclosure Weight 1.2 kg (max), 1.0 kg design goal RF Connector 3x MCX female Radome Plastic color- RAL 9002...
- Page 38 IEC 68-2-1 72 h -45° C High Temperature IEC 68-2-2 72 h +90° C Temp. Cycling IEC 68-2-14 -45° C +90° C 3 Cycles Vibration IEC 60721-3-4 Random min/axis Shock Mechanical IEC 60721-3-4 Humidity ETSI EN300-2-4 144 h T4.1E Wavion Networks...
-
Page 39: Antenna 5.8Ghz Specifications And Patterns
Chapter 8 Antenna 5.8GHz Specifications and Patterns The chapter describes antenna specifications and patterns for the antennas supplied with the Wavion WBS-5800. MT-463009CV 5.8GHz Antenna Azimuth Patterns directional Antenna Installation Guide... - Page 40 MT-463009CV 5.8GHz Antenna Elevation Patterns Wavion Networks...
-
Page 41: Installation Accessories
Chapter 9 Installation Accessories This chapter describes the accessories available for the WBS-2400 and ordering information. The following topics are covered in this chapter: Ethernet Cables • Sun Protection • Lightning Protection • Power Over Ethernet • Installation Guide... -
Page 42: Ethernet Cables
Teldor 8393204101 G.Bares 8215450 jacket 4-pair data cable Sun Protection Product Part Description Name Number Sun Shield for WBS-2400/5800X, extends upper operation WA-SUN- 27009023 temperature range to +60°C Lightning Protection Part Description Manufacturer Contact Information Number Data protection HGLN- Hyperlink www.hyperlinktech.com... -
Page 43: C H A P T E
The Wavion WBS-2400/5800weighs approximately 16 lbs, including all mounting hardware. When the Wavion WBS-2400/5800is mounted on a pole, the sail area of the WBS-2400/5800is approximately 1 square foot. The Wavion WBS-2400/5800can load a pole with a maximum load of 3400 Newton in wind conditions of 165mph. -
Page 44: C H A P T E
DSSS Direct-Sequence Spread Spectrum Electromagnetic Compatibility IEC standard Electrostatic Discharge Federal Communications Commission Hertz HPoE High Power over Ethernet Institute of Electrical and Electronics IEEE Engineers IP67 Ingress Protection Standard ISTA International Safe Transit Association Local Area Network Wavion Networks... - Page 45 Mbps Megabits Per Second Megahertz MIL-STD Military Standard Neutral National Electrical Codes National Electrical Manufacturers NEMA Association Orthogonal Frequency Division OFDM Multiplexing Phase Protective Earth Power over Ethernet RJ45 Registered Jack 45 Received Signal Strength Receive Receive Data Technical Inspection Association Transmit Transmit Data Underwriters Laboratories...
-
Page 46: C H A P T E
Chapter 12 Appendix A: WBS-2400/5800 Product list Part Number Product namer Product description Spatially adaptive, multi radio 2.4GHz WiFi base station, TBD12406101 WBS-2400-FCC 6 antenna FCC/TUV compliant Spatially adaptive, multi radio 2.4GHz WiFi base station, 12406102 WBS-2400-EU 6 antenna ETSI / CE compliant Spatially adaptive, multi radio 2.4GHz WiFi base...