Advertisement
2. Part Name
2.1 Front Panel
GRAPHIC OPERATION TERMINAL
GOT
1000
1) 2)
5)
MITSUBISHI
3) 4)
No
Name
Specifications
Displays the utility screen and the user creation screen.
GT1155-QTBD:320×240 dots, TFT color liquid crystal
1)
Display screen
GT1155-QSBD:320×240 dots, STN color liquid crystal
GT1150-QLBD:320×240 dots, STN monochrome
(white/black) liquid crystal, 16 scales
For operating the touch switches in the utility screen
2)
Touch key
and the user creation screen
USB interface for connecting a personal computer
3)
USB interface
(OS installation, project data download, transparent)
USB environmental
4)
Opens/Closes when the UBS interface is used.
protection cover
Lit in green : Power is correctly supplied
Lit in orange : Screen saving
5)
POWER LED
Blinking in orange/green : Blown backlight bulb
Not lit : Power is not supplied
For the PC connection, refer to the following.
→ GT Designer2 Version
Basic Operation/Data Transfer Manual
2.2 Back Panel
7)
1) 2)
3)
4)
5)
6)
3)
12)
13)
CF CARD
ACCESS
OFF ON
CF CARD
RS-232
RS-422
BATTERY
I/F
INPUT
24V DC
-
+
(FG)
RESEET
10)11)
3)
9)
8)
3)
CF card cover
opened
Power supply terminal layout
Battery cover opened
INPUT
24V DC
-
+
(FG)
14)
No.
Name
Specifications
For communicating with controller (PLC, microcomputer
RS-232
board, bar code reader, RFID, etc) or personal computer
1)
interface
(OS installation, project data download, transparent) (D-
sub 9-pin male)
RS-422
For communicating with controller (PLC, microcomputer
2)
interface
board, etc) (D-sub 9-pin female)
Hole for unit
Hole for the inserting installation fittings (accessory) during
3)
installation
the GOT installation to the panel (4 holes at top and
fitting
bottom)
Rating plate
4)
--
(nameplate)
CF card
5)
Lit: CF card accessed Not lit: CF card not accessed
access LED
Switch for prohibiting access to CF card before removing
CF card
the CF card from the GOT
6)
access switch
ON: CF card being accessed (CF card removal prohibited)
OFF:No access to CF card (CF card removal possible)
7)
CF card cover
Open or close when inserting or removing the CF card.
8)
Reset switch
Hardware reset switch (Use an isolated rod to operate.)
9)
Battery cover
Open or close when replacing the battery.
Power terminal and FG terminal
10)
Power terminal
(for power supply (24VDC) to GOT and grounding)
Power terminal
Open or close when connecting a power terminal. (Color:
11)
cover
transparent)
CF card
12)
Interface for installing the CF card to GOT
interface
CF card eject
13)
Button for removing the CF card
button
GT11-50BAT battery for storing clock data, alarm history
14)
Battery
and recipe data
(The project data is stored in the built-in flash memory.)
For the connection to the controller (PLC, microcomputer board, bar code reader,
RFID, etc) or PC, refer to the following.
→ GOT 1000 Series Connection Manual
3. Specifications
3.1 General Specifications
Item
Display section
0 to 50°C
Operating ambient
temperature
Other than display section 0 to 55°C (When mounted horizontaly), 0 to 50°C (When mounted verticaly)
Storage ambient temperature
-20 to 60°C
Operating ambient humidity
10 to 90% RH, non-condensing (STN liquid crystal type to be stored at or below 39°C WBT.)
Storage ambient humidity
10 to 90% RH, non-condensing (STN liquid crystal type to be stored at or below 39°C WBT.)
Conforms to JIS
Vibration resistance
B3502 and
IEC61131-2
Shock resistance
Conforms to JIS B3502, IEC 61131-2 (147 m/s
Must be free of lamp black, corrosive gas, flammable gas, or excessive amount of electroconductive dust particles and
Operating atmosphere
must be no direct sunlight. (Same as for saving)
*1
2000 m (6562 ft) max.
Operating altitude
Installation location
Inside control panel
ΙΙ or less
Overvoltage category
*2
Pollution degree
*3
2 or less
Cooling method
Self-cooling
*1 Do not use or store the GOT under pressure higher than the atmospheric pressure of altitude 0m (0ft.). Failure to observe this instruction may cause a malfunction.
*2 This indicates the section of the power supply to which the equipment is assumed to be connected between the public electrical power distribution network and the
machinery within the premises.
Category ΙΙ applies to equipment for which electrical power is supplied from fixed facilities.
The surge voltage withstand level for up to the raged voltage of 300 V is 2500 V.
*3 This index indicates the degree to which conductive material is generated in the environment where the equipment is used.
In pollution degree 2, only non-conductive pollution occurs but temporary conductivity may be produced due to condensation.
3.2 Performance Specifications
Item
GT1155-QTBD
Type
TFT color liquid crystal
Screen size
5.7"
320 × 240 dots
Resolution
Display size
W115(4.53) × H86(3.39)[mm](inch) (Horizontal format)
16-dot standard font: 20 characters × 15 lines, 12-dot standard font: 26 characters × 20 lines
Display character
Display
Display color
256 colors
section
*1
Left/Right: 70 degrees, Top: 70 degrees,
Display angle
Bottom: 50 degrees (Horizontal format)
Contrast adjustment
--
Intensity of LCD only
400[cd/m
](Adjustable in 8 levels)
2
Intensity adjustment
8-level adjustment
Life
Approx. 50,000h. (Time for display intensity to become 1/5 at operating ambient temperature of 25°C)
Cold cathode fluorescent tube (irreplaceable by a user) backlight shutoff detection function is included.
Backlight
Backlight off/screen saving time can be set.
Approx. 75,000h or longer (Time for display intensity reaches 50% at the operating
Life
*2
ambient temperature of 25°C)
300 keys/screen (Matrix structure of 15 lines × 20 columns)
Number of touch keys
Key size
Minimum 16 × 16 dots (per key)
To u c h
panel
Number of points touched
Maximum of 2 points
simultaneously
Life
1 million times or more (operating force 0.98N max.)
*3
Flash memory (Internal), for storing project data (3Mbytes) and OS
C drive
Life
Memory
100,000 times
(Number of write times)
D drive
SRAM (Internal), 512kbyes (battery backup)
Specifications
Frequency
Acceleration
Half-amplitude
5 to 9Hz
--
3.5mm
Under intermittent
vibration
9 to 150Hz
9.8m/s
2
5 to 9Hz
--
1.75mm
Under continuous
vibration
9 to 150Hz
4.9m/s
2
2
, 3 times each in X, Y and Z directions)
Specifications
GT1155-QSBD
STN monochrome (white/black) liquid
STN color liquid crystal
crystal
Monochrome (white/black), 16 scales
Left/Right: 55 degrees, Top: 65 degrees,
Left/Right: 45 degrees, Top: 20 degrees,
Bottom: 70 degrees (Horizontal format)
Bottom: 40 degrees (Horizontal format)
16-level adjustment
380[cd/m
](Adjustable in 8 levels)
220[cd/m
](Adjustable in 8 levels)
2
2
Approx. 54,000h or longer (Time for
display intensity reaches 50% at the
operating ambient temperature of 25°C)
Sweep Count
--
10 times each in X,
Y and Z directions
--
GT1150-QLBD
Advertisement
