Page 1 Grand Cherokee 2 0 1 8 O W N E R ’ S M A N U A L...
Page 2 VEHICLES SOLD IN CANADA This manual illustrates and describes the operation of With respect to any Vehicles Sold in Canada, the name features and equipment that are either standard or op- FCA US LLC shall be deemed to be deleted and the name tional on this vehicle.
Page 3 TABLE OF CONTENTS SECTION PAGE INTRODUCTION ..............3 GRAPHICAL TABLE OF CONTENTS .
Page 5: Table Of Contents
INTRODUCTION CONTENTS INTRODUCTION ......4 ROLLOVER WARNING .....7 HOW TO USE THIS MANUAL .
Page 6: Introduction
4 INTRODUCTION This Owner’s Manual has been prepared with the assis- INTRODUCTION tance of service and engineering specialists to acquaint you Dear Customer, congratulations on selecting your new with the operation and maintenance of your vehicle. It is vehicle. Be assured that it represents precision workman- supplemented by Warranty Information, and customer ship, distinctive styling, and high quality.
Page 7: How To Use This Manual
INTRODUCTION described for technical and/or commercial reasons. For HOW TO USE THIS MANUAL further information, contact an authorized dealer. Essential Information If applicable, refer to the owners manual supplement for Consult the Table of Contents to determine which section related information. contains the information you desire.
Page 8: Symbols
6 INTRODUCTION Symbols Consult the following table for a description of the symbols that may be used on your vehicle or throughout this Owner’s Manual:...
Page 9: Rollover Warning
INTRODUCTION ROLLOVER WARNING Utility vehicles have a significantly higher rollover rate than other types of vehicles. This vehicle has a higher ground clearance and a higher center of gravity than many passenger vehicles. It is capable of performing better in a wide variety of off-road applications.
Page 10: Warnings And Cautions
8 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against oper- ating procedures that could result in a collision, bodily injury and/or death. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire Owner’s Manual, you may miss important information.
Page 11 GRAPHICAL TABLE OF CONTENTS CONTENTS FRONT VIEW ......10 INSTRUMENT PANEL .....12 REAR VIEW.
Page 12: Front View
10 GRAPHICAL TABLE OF CONTENTS FRONT VIEW Front View 1 — Hood/Engine Compartment 4 — Wheels/Tires 2 — Windshield 5 — Exterior Mirrors 3 — Headlights 6 — Door Handles...
Page 13: Rear View
GRAPHICAL TABLE OF CONTENTS 11 REAR VIEW Rear View 1 — Rear Lights 2 — Rear Windshield Wiper 3 — Liftgate...
Page 14: Instrument Panel
12 GRAPHICAL TABLE OF CONTENTS INSTRUMENT PANEL Instrument Panel 1 — Air Vents 4 — Instrument Cluster 2 — Paddle Shifter (-) 5 — Paddle Shifter (+) 3 — Steering Wheel 6 — Glove Compartment...
Page 15: Interior
GRAPHICAL TABLE OF CONTENTS 13 INTERIOR Interior Features 1 — Power Window Switches 4 — Switch Panel 2 — Seats 5 — Climate Controls 3 — Transmission Gear Selector 6 — Radio...
Page 17 GETTING TO KNOW YOUR VEHICLE CONTENTS KEYS ....... . .19 SENTRY KEY .
Page 18 16 GETTING TO KNOW YOUR VEHICLE ▫ Keyless Enter-N-Go — Passive Entry ..35 ▫ Power Tilt/Telescoping Steering Column ..56 ▫ Automatic Unlock Doors On Exit ... .40 ▫...
Page 19 GETTING TO KNOW YOUR VEHICLE 17 ▫ Automatic High Beam — If Equipped ..64 ▫ Rain Sensing Wipers — If Equipped ..73 ▫ Flash-To-Pass ......65 ▫...
Page 20 18 GETTING TO KNOW YOUR VEHICLE ▫ Opening Sunroof ......87 ▫ Cargo Area Features .....95 ▫...
Page 21: Keys
GETTING TO KNOW YOUR VEHICLE 19 NOTE: In the ON/RUN position, the lock button is dis- KEYS abled. Only the unlock button is enabled. Key Fob Your vehicle uses a keyless ignition system. The ignition system consists of a key fob with Remote Keyless Entry (RKE) and a START/STOP push button ignition system.
Page 22 20 GETTING TO KNOW YOUR VEHICLE To Unlock The Doors And Liftgate Push the interior door unlock button on the door panel. Push and release the unlock button on the key fob once to unlock the driver’s door or twice within five seconds to unlock all doors and the liftgate.
Page 23 GETTING TO KNOW YOUR VEHICLE 21 To Lock The Doors And Liftgate • Do not touch the battery terminals that are on the back housing or the printed circuit board. Push and release the lock button on the key fob to lock all doors and liftgate.
Page 24 22 GETTING TO KNOW YOUR VEHICLE Emergency Key Removal Key Fob Battery Replacement 3. Remove the battery by turning the back cover over (battery facing downward) and tapping it lightly on a solid surface such as a table or similar and replace the battery.
Page 25 GETTING TO KNOW YOUR VEHICLE 23 Programming Additional Key Fobs • Keys must be ordered to the correct key cut to match the vehicle locks. Programming the key fob may be performed by your authorized dealer. NOTE: Black keys (6.4L) must be replaced with black keys and Red Keys (6.2L) must be replaced with Red Keys.
Page 26: Ignition Switch
24 GETTING TO KNOW YOUR VEHICLE IGNITION SWITCH Keyless Enter-N-Go — Ignition This feature allows the driver to operate the ignition switch with the push of a button as long as the key fob is in the passenger compartment. The Keyless Push Button Ignition has several operating modes that are labeled and will illuminate when in posi- tion.
Page 27: Vehicle On Message
GETTING TO KNOW YOUR VEHICLE 25 WARNING! (Continued) • Driving position. • Do not leave children or animals inside parked • All the electrical devices are available. vehicles in hot weather. Interior heat build-up may cause serious injury or death. START •...
Page 28: Remote Starting System - If Equipped
26 GETTING TO KNOW YOUR VEHICLE NOTE: The power window switches and power sunroof (if WARNING! (Continued) equipped) will remain active up to ten minutes after the • Do not leave the key fob in or near the vehicle, or in ignition is cycled to the OFF position.
Page 29: How To Use Remote Start
GETTING TO KNOW YOUR VEHICLE 27 80° F (26.7° C), and the optional heated seats, and optional How To Use Remote Start heated steering wheel in temperatures below 40° F (4.4° C). • Push Remote Start button on the key fob twice within Refer to “Heated Seats”...
Page 30: Remote Start Abort Message
28 GETTING TO KNOW YOUR VEHICLE • System not disabled from previous remote start event • Remote Start Aborted Timer Expired • Vehicle alarm system indicator flashing • Remote Start Aborted Liftgate Open • Ignition in STOP/OFF position • Remote Start Disabled — Start Vehicle To Reset •...
Page 31: To Exit Remote Start Mode Without Driving The Vehicle
GETTING TO KNOW YOUR VEHICLE 29 feature is enabled, regardless of Remote Start or regular To Exit Remote Start Mode Without Driving The keyless start, the driver heated seat features will automati- Vehicle cally turn on in cold weather. In warm weather, the driver Push and release the Remote Start button one time or allow vented seat feature will automatically turn on when the the remote start cycle to complete the entire 15-minute...
Page 32: Sentry Key
30 GETTING TO KNOW YOUR VEHICLE NOTE: Changes or modifications not expressly approved indicates that someone used an invalid key fob to start the by the party responsible for compliance could void the engine. Either of these conditions will result in the engine user’s authority to operate the equipment.
Page 33: Replacement Keys
GETTING TO KNOW YOUR VEHICLE 31 that are programmed to the vehicle can be used to start and Replacement Keys operate the vehicle. The system will not allow the engine to NOTE: Only key fobs that are programmed to the vehicle crank if an invalid key fob is used to start and operate the electronics can be used to start and operate the vehicle.
Page 34: General Information
32 GETTING TO KNOW YOUR VEHICLE • The horn will pulse General Information The following regulatory statement applies to all radio • The turn signals will flash frequency (RF) devices equipped in this vehicle: • The vehicle security light in the instrument cluster will This device complies with Part 15 of the FCC Rules and flash with Industry Canada license-exempt RSS standard(s).
Page 35: To Disarm The System
GETTING TO KNOW YOUR VEHICLE 33 The vehicle security alarm is designed to protect your To Disarm The System vehicle. However, you can create conditions where the The vehicle security alarm can be disarmed using any of system will give you a false alarm. If one of the previously the following methods: described arming sequences has occurred, the vehicle •...
Page 36: Tamper Alert
34 GETTING TO KNOW YOUR VEHICLE Tamper Alert WARNING! If something has triggered the vehicle security alarm in • For personal security and safety in the event of a your absence, the horn will sound three times and the collision, lock the vehicle doors before you drive as exterior lights will blink three times when you disarm the well as when you park and leave the vehicle.
Page 37: Power Door Locks
GETTING TO KNOW YOUR VEHICLE 35 At the third attempt, the doors will lock even if the key is Power Door Locks inside. The power door lock switches are located on each front door panel. Push the switch to lock or unlock the doors. If the door lock switch is pushed while the ignition is in ACC or ON/RUN and the driver’s door is open, the doors will not lock.
Page 38 36 GETTING TO KNOW YOUR VEHICLE NOTE: To Unlock From The Driver Side • Passive Entry may be programmed ON/OFF; refer to With a valid Passive Entry key fob within 5 ft (1.5 m) of the “Uconnect Settings” in “Multimedia” for further infor- driver’s door handle, grab the front driver door handle to mation.
Page 39 GETTING TO KNOW YOUR VEHICLE 37 To Unlock From The Passenger Side • A lock request is made by the door panel switch while the door is open. With a valid Passive Entry key fob within 5 ft (1.5 m) of the •...
Page 40 38 GETTING TO KNOW YOUR VEHICLE To Lock The Vehicle’s Doors And Liftgate With one of the vehicle’s Passive Entry key fob within 5 ft (1.5 m) of the driver or passenger front door handles, pushing the passive entry lock button will lock the vehicle. DO NOT Grab The Door Handle When Locking NOTE: •...
Page 41 GETTING TO KNOW YOUR VEHICLE 39 • The Passive Entry system will not operate if the key fob battery is dead. The vehicle doors can also be locked by using the lock button located on the vehicle’s interior door panel. To Unlock/Enter The Liftgate The liftgate passive entry unlock feature is built into the electronic liftgate release.
Page 42: Automatic Unlock Doors On Exit
40 GETTING TO KNOW YOUR VEHICLE Automatic Unlock Doors On Exit The doors will unlock automatically on vehicles with power door locks if: 1. The Automatic Unlock Doors On Exit feature is enabled. 2. All doors are closed. 3. The transmission gear selector was not in PARK, then is placed in PARK.
Page 43: Seats
GETTING TO KNOW YOUR VEHICLE 41 • For emergency exit with the system engaged, pull up on the Power Adjustment (Front Seats) door lock knob (unlocked position), roll down the window, Some models may be equipped with eight-way power and open the door with the outside door handle. driver and front passenger seats.
Page 44 42 GETTING TO KNOW YOUR VEHICLE Adjusting The Seat Forward Or Rearward WARNING! The seat can be adjusted both forward and rearward. Push • Adjusting a seat while driving may be dangerous. the seat switch forward or rearward. The seat will move in Moving a seat while driving could result in loss of the direction of the switch.
Page 45: Manual Adjustment (Rear Seats)
GETTING TO KNOW YOUR VEHICLE 43 seat. Push the switch forward to increase the lumbar support. Push the switch rearward to decrease the lumbar support. Pushing upward or downward on the switch will raise and lower the position of the support. Rear Seat Release WARNING! Do not ride with the seatback reclined so that the...
Page 46: Driver Memory Seat - If Equipped
44 GETTING TO KNOW YOUR VEHICLE Driver Memory Seat — If Equipped This feature allows the driver to store up to two different memory profiles for easy recall through a memory switch. Each memory profile contains desired position settings for the driver seat, side mirrors, and power tilt and telescopic steering column (if equipped) and a set of desired radio station presets.
Page 47 GETTING TO KNOW YOUR VEHICLE 45 3. Push and release the set (S) button on the memory To program your key fobs, perform the following: switch. 1. Cycle the vehicle’s ignition to the OFF position. 4. Within five seconds, push and release either of the 2.
Page 48 46 GETTING TO KNOW YOUR VEHICLE Easy Entry/Exit Seat Driver One Memory Position Recall • To recall the memory settings for driver one using the This feature provides automatic driver seat positioning to memory switch, push memory button (1) on the enhance driver mobility when entering and exiting the memory switch.
Page 49: Heated Seats - If Equipped
GETTING TO KNOW YOUR VEHICLE 47 NOTE: The Easy Entry/Exit feature is not enabled when Front Heated Seats the vehicle is delivered from the factory. The Easy Entry/ The front heated seats control buttons are located within Exit feature is enabled (or later disabled) through the the climate or controls screen of the touchscreen.
Page 50 48 GETTING TO KNOW YOUR VEHICLE NOTE: WARNING! (Continued) • Once a heat setting is selected, heat will be felt within • Do not place anything on the seat or seatback that two to five minutes. insulates against heat, such as a blanket or cushion. •...
Page 51: Front Ventilated Seats - If Equipped
GETTING TO KNOW YOUR VEHICLE 49 automatically switch to LO-level after approximately 60 minutes of continuous operation. At that time, the number of indicator lights changes from two to one, indicating the change. The LO-level setting will turn off automatically after approximately 45 minutes.
Page 52: To Lower Rear Seat
50 GETTING TO KNOW YOUR VEHICLE the driver and front passenger cooler in higher ambient To Lower Rear Seat temperatures. The fans operate at two speeds, HI and LO. Either side of the rear seat can be lowered to allow for The front ventilated seats control buttons are located extended cargo space and still maintain some rear seating within the Uconnect system.
Page 53: To Raise Rear Seat
GETTING TO KNOW YOUR VEHICLE 51 NOTE: To Raise Rear Seat • Do not fold the 60% rear seat down with the left Raise the rear seatback and lock it into place. If interference outboard or rear center seat belt buckled. from the cargo area prevents the seatback from fully locking, you will have difficulty returning the seat to its •...
Page 54: Head Restraints
52 GETTING TO KNOW YOUR VEHICLE HEAD RESTRAINTS Supplemental Active Head Restraints — Front Seats Head restraints are designed to reduce the risk of injury by restricting head movement in the event of a rear-impact. Active Head Restraints are passive, deployable compo- Head restraints should be adjusted so that the top of the nents, and vehicles with this equipment cannot be readily head restraint is located above the top of your ear.
Page 55 GETTING TO KNOW YOUR VEHICLE 53 Adjustment Button Active Head Restraint (Normal Position) For comfort, the Active Head Restraints can be tilted forward and rearward. To tilt the head restraint closer to the back of your head, pull forward on the bottom of the head restraint.
Page 56 54 GETTING TO KNOW YOUR VEHICLE WARNING! • ALL the head restraints MUST be reinstalled in the vehicle to properly protect the occupants. • All occupants, including the driver, should not oper- ate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a collision.
Page 57: Adjustment - Rear Seats
GETTING TO KNOW YOUR VEHICLE 55 Adjustment — Rear Seats Head Restraint Removal — Rear Seats The head restraints on the outboard seats are not adjust- The center head restraint can be adjusted when occupied, able. They automatically fold forward when the rear seat is or removed for Child Seat Tethering.
Page 58: Steering Wheel
56 GETTING TO KNOW YOUR VEHICLE WARNING! (Continued) • ALL the head restraints MUST be reinstalled in the vehicle to properly protect the occupants. Follow the re-installation instructions above prior to operating the vehicle or occupying a seat. STEERING WHEEL Power Tilt/Telescoping Steering Column This feature allows you to tilt the steering column upward or downward.
Page 59: Heated Steering Wheel - If Equipped
GETTING TO KNOW YOUR VEHICLE 57 WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death.
Page 60: Mirrors
58 GETTING TO KNOW YOUR VEHICLE • Press the heated steering wheel button a second time MIRRORS to turn the heating element off. Automatic Dimming Mirror NOTE: The engine must be running for the heated steering The mirror head can be adjusted up, down, left, and right wheel to operate.
Page 61: Outside Mirrors
GETTING TO KNOW YOUR VEHICLE 59 WARNING! Vehicles and other objects seen in an outside convex mirror will look smaller and farther away than they really are. Relying too much on side convex mirrors could cause you to collide with another vehicle or other object.
Page 62: If Equipped
60 GETTING TO KNOW YOUR VEHICLE Power mirror preselected positions can be controlled by the Power Mirrors optional Memory Seat Feature. Refer to “Driver Memory The power mirror switch is located on the driver’s side door Seat” in “Getting To Know Your Vehicle” for further infor- trim panel.
Page 63: Heated Mirrors - If Equipped
GETTING TO KNOW YOUR VEHICLE 61 NOTE: The Automatic Fold/Unfold Mirrors feature is not turned on when delivered from the factory. The Automatic Fold/Unfold Mirrors feature can be turned on and off using the Uconnect System. Refer to “Uconnect Settings” in “Multimedia”...
Page 64: Tilt Side Mirrors In Reverse (Available With Memory Seat Only) - If Equipped
62 GETTING TO KNOW YOUR VEHICLE Tilt Side Mirrors In Reverse (Available With Memory Seat Only) — If Equipped Tilt Side Mirrors In Reverse provides automatic outside mirror positioning which will aid the driver’s view of the ground rearward of the front doors. Outside mirrors will move slightly downward from the present position when the vehicle is shifted into REVERSE.
Page 65 GETTING TO KNOW YOUR VEHICLE 63 NOTE: • Your vehicle is equipped with plastic headlight and fog light (if equipped) lenses that are lighter and less sus- ceptible to stone breakage than glass lights. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed.
Page 66: Multifunction Lever
64 GETTING TO KNOW YOUR VEHICLE Multifunction Lever High/Low Beam Switch The multifunction lever is located on the left side of the Push the multifunction lever toward the instrument panel steering column. to switch the headlights to high beams. Pulling the multi- function back toward the steering wheel will turn the low beams back on, or shut the high beams off.
Page 67: Flash-To-Pass
GETTING TO KNOW YOUR VEHICLE 65 • Broken, muddy, or obstructed headlights and taillights NOTE: The engine must be running before the headlights of vehicles in the field of view will cause headlights to will turn on in the Automatic Mode. remain on longer (closer to the vehicle).
Page 68: Headlight Delay
66 GETTING TO KNOW YOUR VEHICLE NOTE: When your headlights come on during the day- Fog Lights — If Equipped time, the instrument panel lights will automatically dim to The fog lights are turned on by rotating the headlight the lower nighttime intensity. switch to the parking light or headlight position and pushing in the headlight rotary control.
Page 69: Turn Signals
GETTING TO KNOW YOUR VEHICLE 67 Turn Signals Battery Saver Move the multifunction lever up or down and the arrows To protect the life of your vehicle’s battery, load shedding on each side of the instrument cluster flash to show proper is provided for both the interior and exterior lights.
Page 70: Courtesy Lights
68 GETTING TO KNOW YOUR VEHICLE detent, will cause all the interior lights to go out. This is Front Map/Reading Lights — If Equipped also known as the “Party” mode because it allows the The front map/reading lights are mounted in the overhead doors to stay open for extended periods of time without console.
Page 71 GETTING TO KNOW YOUR VEHICLE 69 Each light can be turned on by pushing a switch on either Ambient Light — If Equipped side of the console. These buttons are backlit for night time The overhead console is equipped with an ambient light visibility.
Page 72: Windshield Wipers And Washers
70 GETTING TO KNOW YOUR VEHICLE Dimmer Controls WINDSHIELD WIPERS AND WASHERS The brightness of the instrument panel lighting can be The windshield wiper/washer controls are located on the regulated by rotating the dimmer control up (brighter) or multifunction lever on the left side of the steering column. down (dimmer).
Page 73 GETTING TO KNOW YOUR VEHICLE 71 wiper operation and the sixth detent for high wiper Intermittent Wiper System operation. Use one of the four intermittent wiper settings when weather conditions make a single wiping cycle, with a variable delay between cycles, desirable. At driving speeds above 10 mph (16 km/h), the delay can be regulated from a maximum of approximately 18 seconds between cycles (first detent), to a cycle every one second (fourth detent).
Page 74 72 GETTING TO KNOW YOUR VEHICLE Windshield Washer Operation If the end of the lever is pushed while the wipers are in the off position, the wipers will operate for several wipe cycles, To use the washer, push on the end of the lever (toward the then turn off.
Page 75: Rain Sensing Wipers - If Equipped
GETTING TO KNOW YOUR VEHICLE 73 NOTE: The Mist feature does not activate the washer The sensitivity of the system can be adjusted with the pump; therefore, no washer fluid will be sprayed on the multifunction lever. Wiper delay position one is the least windshield.
Page 76: Rear Window Wiper/Washer
74 GETTING TO KNOW YOUR VEHICLE The Rain Sensing system has protection features for the Rear Window Wiper/Washer wiper blades and arms, and will not operate under the The rear wiper/washer controls are located on the multi- following conditions: function lever on the left side of the steering column. The •...
Page 77: Headlight Washers - If Equipped
GETTING TO KNOW YOUR VEHICLE 75 operation. When this rotary control is in the OFF position, NOTE: After turning the ignition switch and headlights ON, rotating it downward will activate the rear washer pump the headlight washers will operate on the first spray of the which will continue to operate as long as the switch is held.
Page 78 76 GETTING TO KNOW YOUR VEHICLE Control Descriptions Icon Description MAX A/C Button Press and release to change the current setting, the indicator illuminates when MAX A/C is on. Performing this function again will cause the MAX A/C operation to switch into manual mode and the MAX A/C indicator will turn off.
Page 79 GETTING TO KNOW YOUR VEHICLE 77 Icon Description Front Defrost Button The Front Defrost button changes the current airflow setting to Defrost mode. The indicator illu- minates when this feature is on. Air comes from the windshield and side window demist out- lets.
Page 80 78 GETTING TO KNOW YOUR VEHICLE Icon Description Faceplate Knob Blower Control Blower Control is used to regulate the amount of air forced through the climate system. There are seven blower speeds available. The speeds can be selected using either the blower control knob on the faceplate or the buttons on the touchscreen.
Page 81 GETTING TO KNOW YOUR VEHICLE 79 Icon Description Floor Mode Floor Mode Air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. Mix Mode Mix Mode Air is directed through the floor, defrost, and side window demister outlets. This setting works best in cold or snowy conditions that require extra heat to the windshield.
Page 82: Climate Control Functions
80 GETTING TO KNOW YOUR VEHICLE Press and release to toggle between MAX A/C and the Climate Control Functions prior settings. The button illuminates when MAX A/C is A/C (Air Conditioning) The Air Conditioning (A/C) button allows the operator to In MAX A/C, the blower level and mode position can be manually activate or deactivate the air conditioning sys- adjusted to desired user settings.
Page 83: Automatic Temperature Control (Atc) - If Equipped
GETTING TO KNOW YOUR VEHICLE 81 • The temperature can be displayed in U.S. or Metric units Automatic Temperature Control (ATC) — If by selecting the US/Metric customer-programmable fea- Equipped ture. Refer to the “Uconnect Settings” in “Multimedia” Automatic Operation for further information.
Page 84 82 GETTING TO KNOW YOUR VEHICLE Winter Operation Outside Air Intake To ensure the best possible heater and defroster perfor- Make sure the air intake, located directly in front of the mance, make sure the engine cooling system is functioning windshield, is free of obstructions, such as leaves.
Page 85 GETTING TO KNOW YOUR VEHICLE 83 Operating Tips Chart...
Page 86: Windows
84 GETTING TO KNOW YOUR VEHICLE NOTE: For vehicles equipped with the Uconnect, the WINDOWS power window switches will remain active for up to 10 Power Window Controls minutes after the ignition is cycled to the OFF position. The window controls on the driver’s door control all the Opening either front door will cancel this feature.
Page 87: Auto-Up Feature With Anti-Pinch Protection
GETTING TO KNOW YOUR VEHICLE 85 To open the window part way, push the window switch WARNING! down briefly and release it when you want the window to stop. There is no anti-pinch protection when the window is almost closed. To avoid personal injury be sure to clear To stop the window from going all the way down during your arms, hands, fingers and all objects from the the Auto-Down operation, pull up on the switch briefly.
Page 88: Wind Buffeting
86 GETTING TO KNOW YOUR VEHICLE push and release the window lockout button again (the to minimize the buffeting. If the buffeting occurs with the indicator light on the button will turn back off). sunroof open, adjust the sunroof opening to minimize the buffeting or open any window.
Page 89: Getting To Know Your Vehicle 87
GETTING TO KNOW YOUR VEHICLE 87 Opening Sunroof WARNING! The sunroof has two programmed automatic stops for the • Never leave children unattended in a vehicle, or with sunroof open position; a comfort stop position and a full access to an unlocked vehicle. Never leave the key open position.
Page 90: Closing Sunroof
88 GETTING TO KNOW YOUR VEHICLE NOTE: If the sunshade is in the closed position when partially open positions. This is a normal occurrence and Express or Manual Open operation is initiated the sun- can be minimized. If the buffeting occurs with the rear shade will automatically open to the half open position windows open, then open the front and rear windows prior to the sunroof opening.
Page 91: Closing Power Shade
GETTING TO KNOW YOUR VEHICLE 89 position. Any release of the switch will stop the movement Pinch Protect Feature and the shade will remain in a partially opened condition This feature will detect an obstruction in the opening of the until the switch is pushed again.
Page 92: Sunroof Maintenance
90 GETTING TO KNOW YOUR VEHICLE Sunroof Maintenance HOOD Use only a non-abrasive cleaner and a soft cloth to clean the To Open The Hood glass panel. To open the hood, two latches must be released. Ignition Off Operation 1. Pull the release lever located below the instrument panel NOTE: and in front of the driver’s door.
Page 93: To Close The Hood
GETTING TO KNOW YOUR VEHICLE 91 2. Reach under the hood, move safety latch to the left and WARNING! lift the hood. Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.
Page 94 92 GETTING TO KNOW YOUR VEHICLE To Unlock/Enter The Liftgate The liftgate may be released in several ways: • Key fob • Outside handle • Button on overhead console The liftgate passive entry unlock feature is built into the electronic liftgate release. With a valid Passive Entry key fob within 5 ft (1.5 m) of the liftgate, push the electronic liftgate release to open with one fluid motion.
Page 95: Closing
GETTING TO KNOW YOUR VEHICLE 93 Power Liftgate — If Equipped WARNING! Driving with the liftgate open can allow poisonous The power liftgate may be opened by pushing exhaust gases into your vehicle. You and your passen- the electronic liftgate release (refer to “Keyless gers could be injured by these fumes.
Page 96 94 GETTING TO KNOW YOUR VEHICLE • If anything obstructs the power liftgate while it is NOTE: closing or opening, the liftgate will automatically re- • In the event of a power malfunction to the liftgate, an verse to the closed or open position, provided it meets emergency liftgate latch release can be used to open the sufficient resistance.
Page 97: Cargo Area Features
GETTING TO KNOW YOUR VEHICLE 95 WARNING! • Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your pas- sengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle. •...
Page 98 96 GETTING TO KNOW YOUR VEHICLE Retractable Cargo Area Cover — If Equipped NOTE: The purpose of this cover is for privacy, not to secure loads. It will not prevent cargo from shifting or protect passengers from loose cargo. To cover the cargo area: 1.
Page 99 GETTING TO KNOW YOUR VEHICLE 97 Rear Cargo Tie-Downs The rear cargo tie-downs, located on the cargo area floor, should be used to safely secure loads when the vehicle is moving. Rear Cargo Cover WARNING! In a collision, a loose cargo cover in the vehicle could cause injury.
Page 100: Garage Door Opener - If Equipped
98 GETTING TO KNOW YOUR VEHICLE GARAGE DOOR OPENER — IF EQUIPPED WARNING! (Continued) HomeLink replaces up to three hand-held transmitters that only, not for passengers, who should sit in seats and operate devices such as garage door openers, motorized use seat belts.
Page 101: Before You Begin Programming Homelink
GETTING TO KNOW YOUR VEHICLE 99 Programming A Rolling Code Before You Begin Programming HomeLink Be sure that your vehicle is parked outside of the garage For programming garage door openers that were manufac- before you begin programming. tured after 1995. These garage door openers can be identi- fied by the “LEARN”...
Page 102: Getting To Know Your Vehicle 15
100 GETTING TO KNOW YOUR VEHICLE 1. Place the ignition in the ON/RUN position. 6. Return to the vehicle and push the programmed HomeLink button twice (holding the button for two 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) seconds each time).
Page 103: Canadian/Gate Operator Programming
GETTING TO KNOW YOUR VEHICLE 101 Programming A Non-Rolling Code • To program the two remaining HomeLink buttons, repeat each step for each remaining button. DO NOT For programming Garage Door Openers manufactured erase the channels. before 1995. Reprogramming A Single HomeLink Button (Non- 1.
Page 104 102 GETTING TO KNOW YOUR VEHICLE the signal during programming. Similar to this Canadian NOTE: law, some U.S. gate operators are designed to time-out in • If the indicator light stays on constantly, programming the same manner. is complete and the garage door/device should acti- vate when the HomeLink button is pressed.
Page 105: Using Homelink
GETTING TO KNOW YOUR VEHICLE 103 • Did you unplug the device for programming and re- Using HomeLink member to plug it back in? To operate, push and release the programmed HomeLink button. Activation will now occur for the programmed If you have any problems, or require assistance, please call device (i.e.
Page 106: General Information
104 GETTING TO KNOW YOUR VEHICLE General Information INTERNAL EQUIPMENT The following regulatory statement applies to all Radio Storage Frequency (RF) devices equipped in this vehicle: Glove Compartment This device complies with Part 15 of the FCC Rules and The glove compartment is located on the passenger side of with Industry Canada license-exempt RSS standard(s).
Page 107 GETTING TO KNOW YOUR VEHICLE 105 To open the glove compartment, pull the release handle. Door Storage Large storage areas are built into the door panels for easy access. Opened Glove Compartment Door Panel Storage...
Page 108 106 GETTING TO KNOW YOUR VEHICLE Console Features To open the upper storage compartment, pull upward on the small latch located on the lid. The center console contains both an upper and a lower storage area. Storage Compartment Latches Storage Compartment...
Page 109 GETTING TO KNOW YOUR VEHICLE 107 Lift upward on the larger of the latches to access the lower storage compartment. Lower Storage Compartment CD/DVD Player — If Equipped Lower Storage Compartment WARNING! Your vehicle may have an optional CD or DVD player Do not operate this vehicle with a console compart- located in the center console.
Page 110: Cupholders
108 GETTING TO KNOW YOUR VEHICLE Overhead Console Cupholders The overhead console contains courtesy/reading lights There are two cupholders for the front seat passengers and storage for sunglasses. Universal Garage Door Opener located in the center console. (HomeLink), power liftgate and power sunroof switches may also be included, if equipped.
Page 111: Electrical Power Outlets
GETTING TO KNOW YOUR VEHICLE 109 There are two cupholders for the rear seat passengers Power outlets labeled with a “key” are powered when the located in the fold-down center armrest. ignition is in the ON or ACC position, while the outlets labeled with a “battery”...
Page 112 110 GETTING TO KNOW YOUR VEHICLE The front power outlet is located inside the storage area on In addition to the front power outlet, there is also a power the center stack of the instrument panel. Push inward on outlet located in the storage area of the center console. the storage lid to open the compartment and gain access to this power outlet.
Page 113 GETTING TO KNOW YOUR VEHICLE 111 The rear power outlet is located in the right rear cargo area. NOTE: The rear power outlet can be switched from switched “ignition” only to constant “battery” powered all the time. See your local authorized dealer for details. Rear Power Outlet Power Outlet Right Rear Quarter Panel Fuse...
Page 114 112 GETTING TO KNOW YOUR VEHICLE WARNING! (Continued) • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure. CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.).
Page 115: Power Inverter - If Equipped
GETTING TO KNOW YOUR VEHICLE 113 The power inverter is designed with built-in overload Power Inverter — If Equipped protection. If the power rating of 150 Watts is exceeded, the There is a 115 Volt, 150 Watt inverter outlet located on the power inverter will automatically shut down.
Page 116: Sunglasses Bin Door
114 GETTING TO KNOW YOUR VEHICLE NOTE: If not equipped with crossbars, your authorized Sunglasses Bin Door dealer can order and install Mopar crossbars built specifi- At the front of the console, a compartment is provided for cally for this roof rack system. storing a pair of sunglasses.
Page 117 GETTING TO KNOW YOUR VEHICLE 115 • If any cargo (or any metallic object) is placed over the CAUTION! (Continued) satellite radio antenna (if equipped), you may experi- • To avoid damage to the roof rack and vehicle, do not ence interruption of satellite radio reception.
Page 119 GETTING TO KNOW YOUR INSTRUMENT PANEL CONTENTS INSTRUMENT CLUSTER ....118 ▫ Green Indicator Lights ....141 ▫...
Page 120: Instrument Cluster
118 GETTING TO KNOW YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER SRT Instrument Cluster...
Page 121: Instrument Cluster Descriptions
GETTING TO KNOW YOUR INSTRUMENT PANEL 119 Instrument Cluster Descriptions CAUTION! 1. Speedometer Driving with a hot engine cooling system could dam- • Indicates vehicle speed. age your vehicle. If the temperature gauge reads “H” pull over and stop the vehicle. Idle the vehicle with the 2.
Page 122: Instrument Cluster Display
120 GETTING TO KNOW YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DISPLAY Your vehicle will be equipped with an instrument cluster display, which offers useful information to the driver. With the ignition in the STOP/OFF mode, opening/closing of a door will activate the display for viewing, and display the total miles, or kilometers, in the odometer.
Page 123 GETTING TO KNOW YOUR INSTRUMENT PANEL 121 • Stored Messages • Up Arrow Button • Screen Setup Push and release the up arrow button to scroll upward through the Main Menu items. • Diagnostic • Speed Warning • Down Arrow Button The system allows the driver to select information by Push and release the down arrow button to scroll pushing the following buttons mounted on the steering...
Page 124 122 GETTING TO KNOW YOUR INSTRUMENT PANEL Oil Change Reset Secondary Method For Oil Change Reset Procedure Your vehicle is equipped with an engine oil change indi- 1. Without pushing the brake pedal, push and release the cator system. The “Oil Change Required” message will ENGINE START/STOP button and place the ignition to display in the instrument cluster display for five seconds the ON/RUN position (do not start the engine).
Page 125 GETTING TO KNOW YOUR INSTRUMENT PANEL 123 • Oil Change Due • Lights On • Fuel Low • Right Front Turn Signal Light Out • Service Anti-lock Brake System • Right Rear Turn Signal Light Out • Service Electronic Throttle Control •...
Page 126 124 GETTING TO KNOW YOUR INSTRUMENT PANEL • Doors Open cluster display. Push and release the left or right arrow buttons to change between large and small speedometer • Liftgate Open display. Push and release the OK button to toggle units •...
Page 127 GETTING TO KNOW YOUR INSTRUMENT PANEL 125 Terrain — If Equipped WARNING! (Continued) Push and release the up or down arrow button until the reckless or dangerous manner, which can jeopardize Terrain icon/title is highlighted in the instrument cluster the user’s safety or the safety of others. Only a safe, display.
Page 128 126 GETTING TO KNOW YOUR INSTRUMENT PANEL • 1/8 Mile (200 meters) Timer Driver Assist – Best Push and release the up or down arrow button until the – Last Driver Assist menu title is highlighted in the instrument cluster display. –...
Page 129 GETTING TO KNOW YOUR INSTRUMENT PANEL 127 Push and release the SET + or the SET- button (located on The instrument cluster display displays the current Lane- the steering wheel) and the following will display in the Sense system settings. The information displayed depends instrument cluster display: on LaneSense system status and the conditions that need to be met.
Page 130 128 GETTING TO KNOW YOUR INSTRUMENT PANEL • Average – The display shows the average fuel economy Stored Messages (MPG, L/100 km, or km/L) since the last reset. Push and release the up or down arrow button until the • Current – This display shows the current fuel economy Messages Menu Icon is highlighted in the instrument (MPG, L/100 km, km/L) while driving.
Page 131 GETTING TO KNOW YOUR INSTRUMENT PANEL 129 • Outside Temp Defaults (Restores All Settings To Default Settings) • Cancel • Time • Restore • Range Current Gear • Fuel Economy Average • On • Fuel Economy Current • Off (default setting) •...
Page 132 130 GETTING TO KNOW YOUR INSTRUMENT PANEL The menu with (show/hide) means user can press OK Battery Saver On/Battery Saver Mode Message — button to choose show or hide this menu on the instrument Electrical Load Reduction Actions — If Equipped cluster display.
Page 133 GETTING TO KNOW YOUR INSTRUMENT PANEL 131 NOTE: are larger than the capability of charging system. The charging system is still functioning properly. • The charging system is independent from load reduc- tion. The charging system performs a diagnostic on the •...
Page 134: Trip Computer
132 GETTING TO KNOW YOUR INSTRUMENT PANEL What to do when an electrical load reduction action TRIP COMPUTER message is present (“Battery Saver On” or “Battery Saver Push and release the up or down arrow button until the Mode”) Trip A or Trip B icon is highlighted in the instrument cluster display (Toggle left or right to select Trip A or Trip During a trip: B).
Page 135: Warning Lights And Messages
GETTING TO KNOW YOUR INSTRUMENT PANEL 133 To Reset A Trip Function If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the Reset will only occur while a resettable function is selected master cylinder reservoir, it indicates a possible brake (highlighted).
Page 136 134 GETTING TO KNOW YOUR INSTRUMENT PANEL — Battery Charge Warning Light WARNING! This light illuminates when the battery is not charging Driving a vehicle with the red brake light on is properly. If it stays on while the engine is running, there dangerous.
Page 137 GETTING TO KNOW YOUR INSTRUMENT PANEL 135 — Electronic Throttle Control (ETC) Warning — Engine Coolant Temperature Warning Light Light This light warns of an overheated engine condition. If the This light informs you of a problem with the Electronic engine coolant temperature is too high, this indicator will Throttle Control (ETC) system.
Page 138 136 GETTING TO KNOW YOUR INSTRUMENT PANEL NOTE: If the vehicle is moving, there will also be a single flash or remain on continuously and a chime will sound. chime. Refer to “Occupant Restraints Systems” in “Safety” for further information. —...
Page 139: Yellow Warning Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL 137 — Vehicle Security Warning Light — If Equipped — Electronic Stability Control (ESC) Off Warning Light — If Equipped This light will flash at a fast rate for approximately 15 seconds when the vehicle security alarm is arming, and This light indicates the Electronic Stability Control (ESC) is then will flash slowly until the vehicle is disarmed.
Page 140 138 GETTING TO KNOW YOUR INSTRUMENT PANEL • The “ESC Off Indicator Light” and the “ESC Indicator — Low Fuel Warning Light Light” come on momentarily each time the ignition is When the fuel level reaches approximately 2.4 gal (9.1 L) placed in the ON/RUN or ACC/ON/RUN position.
Page 141 GETTING TO KNOW YOUR INSTRUMENT PANEL 139 several typical driving styles. In most situations, the ve- — Forward Collision Warning Light — If hicle will drive normally and will not require towing. Equipped This telltale will turn on to indicate a fault in the Forward When the engine is running, the MIL may flash to alert Collision Warning System.
Page 142 140 GETTING TO KNOW YOUR INSTRUMENT PANEL Please note that the TPMS is not a substitute for proper tire CAUTION! (Continued) maintenance, and it is the driver’s responsibility to main- occurs, repair immediately using the dedicated tire tain correct tire pressure, even if under-inflation has not repair kit and contact your authorized dealer as soon as reached the level to trigger illumination of the TPMS low possible.
Page 143: Yellow Indicator Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL 141 Green Indicator Lights CAUTION! — Adaptive Cruise Control (ACC) Set With No The TPMS has been optimized for the original equip- Target Detected Indicator Light — If Equipped ment tires and wheels. TPMS pressures and warning This light will turn on when the Adaptive Cruise Control is have been established for the tire size equipped on SET and there is no target vehicle detected.
Page 144: White Indicator Lights
142 GETTING TO KNOW YOUR INSTRUMENT PANEL — LaneSense Indicator Light — If Equipped — Track Mode SRT Indicator Light This light will turn on when Track Mode is active. The LaneSense indicator is solid green when both lane markings have been detected and the system is “armed” Refer to “Selec-Track”...
Page 145: Blue Indicator Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL 143 Custom Mode SRT Indicator Light NOTE: The indication will not turn yellow and flash with a continuous chime unless the speed is exceeded by This light will turn on when Custom Mode SRT is active. 1.9 mph (3 km/h) or more.
Page 146: Onboard Diagnostic System - Obd Ii
144 GETTING TO KNOW YOUR INSTRUMENT PANEL the rear of the vehicle) to turn off the high beams. If the CAUTION! (Continued) high beams are off, pull the lever toward you for a vehicle must be serviced before any emissions tests temporary high beam on, flash to pass scenario.
Page 147: Emissions Inspection And Maintenance Programs
GETTING TO KNOW YOUR INSTRUMENT PANEL 145 Normally, the OBD II system will be ready. The OBD II WARNING! (Continued) system may not be ready if your vehicle was recently • Be possible that vehicle systems, including safety serviced, recently had a dead battery or a battery replace- related systems, could be impaired or a loss of ment.
Page 148 146 GETTING TO KNOW YOUR INSTRUMENT PANEL • The MIL will not flash at all and will remain fully illuminated until you place the ignition in the off posi- tion or start the engine. This means that your vehicle’s OBD II system is ready and you can proceed to the I/M station.
Page 149 SAFETY CONTENTS SAFETY FEATURES ..... .148 ▫ Seat Belt Systems ..... .181 ▫...
Page 150: Safety Features
148 SAFETY These are all normal characteristics of ABS. SAFETY FEATURES Anti-Lock Brake System (ABS) WARNING! The Anti-Lock Brake System (ABS) provides increased • The ABS contains sophisticated electronic equip- vehicle stability and brake performance under most brak- ment that may be susceptible to interference caused ing conditions.
Page 151: Electronic Brake Control System
SAFETY Electronic Brake Control System WARNING! (Continued) Your vehicle is equipped with an advanced Electronic • The capabilities of an ABS equipped vehicle must Brake Control system (EBC). This system includes Elec- never be exploited in a reckless or dangerous manner tronic Brake Force Distribution (EBD), Anti-Lock Brake that could jeopardize the user’s safety or the safety of System (ABS), Brake Assist System (BAS), Hill Start Assist...
Page 152 150 SAFETY If the “Brake System Warning Light” remains on or comes WARNING! on while driving, it indicates that the brake system is not functioning properly and that immediate service is re- The Brake Assist System (BAS) cannot prevent the quired.
Page 153 SAFETY The following conditions must be met in order for HSA to WARNING! (Continued) activate: while pulling a trailer. HSA is not a substitute for • The feature must be enabled. active driving involvement. It is always the driver’s • The vehicle must be stopped. responsibility to be attentive to distance to other ve- hicles, people, and objects, and most importantly brake •...
Page 154 152 SAFETY For vehicles not equipped with an instrument cluster Towing With HSA display, perform the following steps: HSA will also provide assistance to mitigate roll back while towing a trailer. 1. Center the steering wheel (front wheels pointing straight forward). WARNING! 2.
Page 155 SAFETY reduce engine power to provide enhanced acceleration and • Oversteer — when the vehicle is turning more than stability. A feature of the TCS, Brake Limited Differential appropriate for the steering wheel position. (BLD), functions similar to a limited slip differential and •...
Page 156 154 SAFETY ESC On WARNING! (Continued) This is the normal operating mode for the ESC. Whenever from loss of vehicle control due to inappropriate the vehicle is started, the ESC system will be in this mode. driver input for the conditions. Only a safe, attentive, This mode should be used for most driving conditions.
Page 157 SAFETY NOTE: System may switch from ESC “Full Off” to “Partial WARNING! Off” mode when vehicle exceeds a predetermined speed. When the vehicle speed slows below the predetermined • When in “Partial Off” mode, the TCS functionality speed the system will return to ESC “Full Off”. of ESC, (except for the limited slip feature described in the TCS section), has been disabled and the “ESC “Full Off”...
Page 158 156 SAFETY The “ESC Activation/Malfunction Indicator Light” (lo- WARNING! (Continued) cated in the instrument cluster) starts to flash as soon as the Off” mode is only intended for off-highway or off- tires lose traction and the ESC system becomes active. The road use.
Page 159 SAFETY Electronic Roll Mitigation (ERM) WARNING! (Continued) This system anticipates the potential for wheel lift by leaving the roadway or striking objects or other ve- monitoring the driver’s steering wheel input and the speed hicles. The capabilities of an ERM-equipped vehicle of the vehicle.
Page 160 158 SAFETY Dynamic Steering Torque (DST) WARNING! Dynamic Steering Torque is a feature of the ESC and If TSC activates while driving, slow the vehicle down, Electric Power Steering (EPS) modules that provides stop at the nearest safe location, and adjust the trailer torque at the steering wheel for certain driving conditions load to eliminate trailer sway.
Page 161 SAFETY HDC has three states: HDC Target Set Speeds • P = No set speed. HDC may be enabled but will not 1. Off (feature is not enabled and will not activate). activate 2. Enabled (feature is enabled and ready but activation •...
Page 162 160 SAFETY • The vehicle is driven greater than 20 mph (32 km/h) for Driver Override greater than 70 seconds. The driver may override HDC activation with throttle or • The vehicle is driven greater than 40 mph (64 km/h) brake application at anytime.
Page 163 SAFETY • Vehicle speed is below 5 mph (8 km/h). WARNING! • Parking brake is released. HDC is only intended to assist the driver in controlling • Driver door is closed. vehicle speed when descending hills. The driver must remain attentive to the driving conditions and is re- •...
Page 164 162 SAFETY • 3rd = 1.8 mph (3 km/h) Driver Override: • 4th = 2.5 mph (4 km/h) The driver may override SSC activation with throttle or brake application at any time. • 5th = 3.1 mph (5 km/h) Deactivating SSC •...
Page 165: Auxiliary Driving Systems
SAFETY • The vehicle is driven greater than 40 mph (64 km/h) WARNING! (SSC exits immediately). SSC is only intended to assist the driver in controlling Feedback To The Driver: vehicle speed when driving in off road conditions. The The instrument cluster has an SSC icon and the SSC switch driver must remain attentive to the driving conditions has an LED which offer feedback to the driver about the and is responsible for maintaining a safe vehicle...
Page 166 164 SAFETY both sides of the vehicle when the vehicle speed reaches approximately 6 mph (10 km/h) or higher and will alert the driver of vehicles in these areas. NOTE: • The BSM system DOES NOT alert the driver about rapidly approaching vehicles that are outside the detec- tion zones.
Page 167 SAFETY contamination so that the BSM system can function prop- erly. Do not block the area of the rear fascia where the radar sensors are located with foreign objects (bumper stickers, bicycle racks, etc.). Warning Light Location The BSM system monitors the detection zone from three different entry points (side, rear, front) while driving to see if an alert is necessary.
Page 168 166 SAFETY Entering From The Side Entering From The Rear Vehicles that move into your adjacent lanes from either Vehicles that come up from behind your vehicle on either side of the vehicle. side and enter the rear detection zone with a relative speed of less than 30 mph (48 km/h).
Page 169 SAFETY Overtaking Traffic If you pass another vehicle slowly with a relative speed less than 15 mph (24 km/h) and the vehicle remains in the blind spot for approximately 1.5 seconds, the warning light will be illuminated. If the difference in speed between the two vehicles is greater than 15 mph (24 km/h), the warning light will not illuminate.
Page 170 168 SAFETY Stationary Objects Opposing Traffic The BSM system will not alert you of objects that are WARNING! traveling in the opposite direction of the vehicle in adjacent lanes. The Blind Spot Monitoring system is only an aid to help detect objects in the blind spot zones. The BSM system is not designed to detect pedestrians, bicyclists, or animals.
Page 171 SAFETY Rear Cross Path (RCP) (5 km/h), to objects moving a maximum of approximately 20 mph (32 km/h), such as in parking lot situations. The Rear Cross Path (RCP) feature is intended to aid the driver when backing out of parking spaces where their NOTE: In a parking lot situation, oncoming vehicles can be vision of oncoming vehicles may be blocked.
Page 172 170 SAFETY Modes Of Operation NOTE: Whenever an audible alert is requested by the BSM system, the radio is also muted. Three selectable modes of operation are available in the Uconnect System. Refer to “Uconnect Settings” in “Multi- When the system is in RCP, the system shall respond with media”...
Page 173: Forward Collision Warning (Fcw) With Mitigation
SAFETY 2. This device must accept any interference received, in- warnings by braking and the system determines that the cluding interference that may cause undesired opera- driver intends to avoid the collision by braking but has not tion. applied sufficient brake force, the system will compensate and provide additional brake force as required.
Page 174 172 SAFETY When the system determines a collision with the vehicle in WARNING! front of you is no longer probable, the warning message will be deactivated. Forward Collision Warning (FCW) is not intended to avoid a collision on its own, nor can FCW detect every NOTE: type of potential collision.
Page 175 SAFETY latter is at a farther distance than Medium setting. This NOTE: provides the most reaction time to avoid a possible colli- • The system will retain the last setting selected by the sion. driver after ignition shut down. Changing the FCW status to the “Near” setting, allows the •...
Page 176: Tire Pressure Monitor System (Tpms)
174 SAFETY Service FCW Warning The tire pressure will vary with temperature by about 1 psi (7 kPa) for every 12°F (6.5°C). This means that when the If the system turns off, and the instrument cluster displays: outside temperature decreases, the tire pressure will de- •...
Page 177 SAFETY NOTE: When filling warm tires, the tire pressure may need CAUTION! to be increased up to an additional 4 psi (30 kPa) above the recommended cold placard pressure in order to turn the • The TPMS has been optimized for the original Tire Pressure Monitoring Telltale Light off.
Page 178 176 SAFETY NOTE: monitor tire pressure levels. Sensors, mounted to each wheel as part of the valve stem, transmit tire pressure • The TPMS is not intended to replace normal tire care and readings to the Receiver Module. maintenance, or to provide warning of a tire failure or condition.
Page 179 SAFETY • Various Tire Pressure Monitoring System Messages, which display in the instrument cluster, and a graphic displaying tire pressures • Tire Pressure Monitoring Telltale Light Tire Pressure Monitoring Low Pressure Warnings The Tire Pressure Monitoring Telltale Light will illuminate in the instrument cluster, and an audible chime will be activated, when one or more of the four active road tire pressures are low.
Page 180 178 SAFETY • Installing some form of aftermarket window tinting that the Tire Pressure Monitoring Telltale Light will extinguish once the updated tire pressure(s) have been received. The affects radio wave signals. vehicle may need to be driven for up to 20 minutes above •...
Page 181 SAFETY instrument cluster display will display a SERVICE TPM 75 seconds and then remain on. The instrument cluster will SYSTEM message for five seconds and then display display the “SERVICE TPM SYSTEM” message and then dashes (- -) in place of the pressure value. Once you repair display dashes (--) in place of the pressure values.
Page 182: Occupant Restraint Systems
180 SAFETY (1) This device may not cause harmful interference, and Important Safety Precautions Please pay close attention to the information in this section. (2) This device must accept any interference received, It tells you how to use your restraint system properly, to including interference that may cause undesired operation.
Page 183: Seat Belt Systems
SAFETY 5. You should read the instructions provided with your WARNING! (Continued) child restraint to make sure that you are using it younger, including a child in a rear-facing child properly. restraint. 6. All occupants should always wear their lap and shoul- •...
Page 184 182 SAFETY seat belts. The Belt Alert feature is active whenever the has completed, the Seat Belt Reminder Light will remain on ignition switch is in the START or ON/RUN position. until the seat belts are buckled. The BeltAlert warning sequence may repeat based on vehicle speed until the Initial Indication driver and occupied outboard front seat passenger seat...
Page 185 SAFETY NOTE: If BeltAlert has been deactivated and the driver or WARNING! (Continued) outboard front seat passenger (if equipped with outboard • In a collision, you and your passengers can suffer front passenger seat BeltAlert) is unbuckled the Seat Belt much greater injuries if you are not properly buckled Reminder Light will turn on and remain on until the driver up.
Page 186 184 SAFETY WARNING! (Continued) WARNING! (Continued) • A seat belt that is buckled into the wrong buckle will seat belt. Follow these instructions to wear your seat belt safely and to keep your passengers safe, too. not protect you properly. The lap portion could ride •...
Page 187 SAFETY WARNING! (Continued) • A frayed or torn seat belt could rip apart in a collision and leave you with no protection. Inspect the seat belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately.
Page 188 186 SAFETY Inserting Latch Plate Into Buckle Positioning The Lap Belt 4. Position the lap belt so that it is snug and lies low across 5. Position the shoulder belt across the shoulder and chest your hips, below your abdomen. To remove slack in the with minimal, if any slack so that it is comfortable and lap belt portion, pull up on the shoulder belt.
Page 189 SAFETY Lap/Shoulder Belt Untwisting Procedure Use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point. 2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the seat belt webbing 180 degrees to create a fold that begins immediately above the latch plate.
Page 190 188 SAFETY NOTE: The adjustable upper shoulder belt anchorage is Seat Belt Extender equipped with an Easy Up feature. This feature allows the If a seat belt is not long enough to fit properly, even when shoulder belt anchorage to be adjusted in the upward the webbing is fully extended and the adjustable upper position without pushing or squeezing the release button.
Page 191 SAFETY Seat Belts And Pregnant Women Seat Belt Pretensioner The front seat belt system is equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices may improve the performance of the seat belt by removing slack from the seat belt early in a collision.
Page 192 190 SAFETY Switchable Automatic Locking Retractor (ALR) ALR is activated, you will hear a clicking sound as the seat belt retracts. Allow the webbing to retract completely in The seat belts in the passenger seating positions are this case and then carefully pull out only the amount of equipped with a Switchable Automatic Locking Retractor webbing necessary to comfortably wrap around the occu- (ALR) which is used to secure a child restraint system.
Page 193 SAFETY How To Engage The Automatic Locking Mode WARNING! (Continued) 1. Buckle the combination lap and shoulder belt. • Do not use the Automatic Locking Mode to restrain occupants who are wearing the seat belt or children 2. Grasp the shoulder portion and pull downward until who are using booster seats.
Page 194 192 SAFETY between the back of the occupant’s head and the AHR. This Active Head Restraint (AHR) Components: system is designed to help prevent or reduce the extent of injuries to the driver and front passenger in certain types of rear impacts.
Page 195 SAFETY Resetting Active Head Restraints (AHR) WARNING! (Continued) restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a collision. • Do not place items over the top of the Active Head Restraint, such as coats, seat covers or portable DVD players.
Page 196: Supplemental Restraint Systems (Srs)
194 SAFETY • Knee Impact Bolsters WARNING! • Driver and Front Passenger Air Bags Deployed AHRs are not able to best protect you in all • Seat Belt Buckle Switch types of collisions. Have deployed AHRs reset by an authorized dealer immediately. •...
Page 197 SAFETY ON/RUN position. After the self-check, the Air Bag Warn- the air bags may not be ready to inflate for your protection. ing Light will turn off. If the ORC detects a malfunction in Have an authorized dealer service the air bag system any part of the system, it turns on the Air Bag Warning immediately.
Page 198 196 SAFETY service the vehicle immediately. For additional information regarding the Redundant Air Bag Warning Light refer to “Getting To Know Your Instrument Panel” section of this manual. Front Air Bags This vehicle has front air bags and lap/shoulder belts for both the driver and front passenger.
Page 199 SAFETY buckle switch may adjust the inflation rate of the Ad- WARNING! (Continued) vanced Front Air Bags. • Never place a rear-facing child restraint in front of an air bag. A deploying passenger front air bag can WARNING! cause death or serious injury to a child 12 years or •...
Page 200 198 SAFETY rollover collisions. The front air bags will not deploy in all inflate in less time than it takes to blink your eyes. The frontal collisions, including some that may produce sub- front air bags then quickly deflate while helping to restrain stantial vehicle damage —...
Page 201 SAFETY Supplemental Side Air Bags Supplemental Seat-Mounted Side Air Bags (SABs) This vehicle is equipped with Supplemental Seat-Mounted Side Air Bags (SABs). Supplemental Seat-Mounted Side Air Bags (SABs) are located in the outboard side of the front seats. The SABs are marked with a “SRS AIRBAG”...
Page 202 200 SAFETY WARNING! Do not use accessory seat covers or place objects between you and the Side Air Bags; the performance could be adversely affected and/or objects could be pushed into you, causing serious injury. Supplemental Side Air Bag Inflatable Curtains (SABICs) This vehicle is equipped with Supplemental Side Air Bag Inflatable Curtains (SABICs).
Page 203 SAFETY The SABICs may help reduce the risk of partial or complete ORC in determining the appropriate response to impact ejection of vehicle occupants through side windows in events. The system is calibrated to deploy the Side Air Bags certain side impact events. on the impact side of the vehicle during impacts that require Side Air Bag occupant protection.
Page 204 202 SAFETY WARNING! (Continued) WARNING! (Continued) • Relying on the Side Air Bags alone could lead to or killed. Occupants, including children, should more severe injuries in a collision. The Side Air Bags never lean on or sleep against the door, side win- work with your seat belt to restrain you properly.
Page 205 SAFETY The SABICs may help reduce the risk of partial or complete If A Deployment Occurs ejection of vehicle occupants through side windows in The front air bags are designed to deflate immediately after certain rollover or side impact events. deployment.
Page 206 204 SAFETY irritation, move to fresh air. If the irritation continues, Enhanced Accident Response System see your doctor. If these particles settle on your clothing, In the event of an impact, if the communication network follow the garment manufacturer’s instructions for remains intact, and the power remains intact, depending cleaning.
Page 207 SAFETY Maintaining Your Air Bag System WARNING! (Continued) dealer. Only manufacturer approved seat accessories WARNING! may be used. If it is necessary to modify the air bag • Modifications to any part of the air bag system could system for persons with disabilities, contact your cause it to fail when you need it.
Page 208: Child Restraints
206 SAFETY These data can help provide a better understanding of the Children 12 years or younger should ride properly buckled circumstances in which crashes and injuries occur. up in a rear seat, if available. According to crash statistics, children are safer when properly restrained in the rear NOTE: EDR data are recorded by your vehicle only if a seats rather than in the front.
Page 209 SAFETY NOTE: • Canadian residents should refer to Transport Canada’s website for additional information: http://www.tc.gc.ca/ • For additional information, refer to www.safercar.gov/ eng/motorvehiclesafety/safedrivers-childsafety-index-53.htm parents/index.htm or call: 1–888–327–4236 Summary Of Recommendations For Restraining Children In Vehicles Recommended Type Of Child Child Size, Height, Weight Or Age Restraint Infants and Toddlers Children who are two years old or...
Page 210 208 SAFETY Infant And Child Restraints WARNING! (Continued) Safety experts recommend that children ride rear-facing in • Only use a rear-facing child restraint in a vehicle the vehicle until they are two years old or until they reach with a rear seat. either the height or weight limit of their rear-facing child restraint.
Page 211 SAFETY Children Too Large For Booster Seats WARNING! Children who are large enough to wear the shoulder belt • Improper installation can lead to failure of an infant comfortably, and whose legs are long enough to bend over or child restraint. It could come loose in a collision. the front of the seat when their back is against the seatback, The child could be badly injured or killed.
Page 212 210 SAFETY If the answer to any of these questions was “no,” then the WARNING! child still needs to use a booster seat in this vehicle. If the child is using the lap/shoulder belt, check seat belt fit Never allow a child to put the shoulder belt under an periodically and make sure the seat belt buckle is latched.
Page 213 SAFETY Lower Anchors And Tethers For CHildren (LATCH) used with the top tether anchorage to install the child Restraint System restraint. Please see the following table for more information. LATCH Positions For Installing Child Restraints In This Vehicle LATCH Label Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren.
Page 214 212 SAFETY Frequently Asked Questions About Installing Child Restraints With LATCH What is the weight limit (child’s weight + 65 lbs (29.5 kg) Use the LATCH anchorage system until the weight of the child restraint) for using the combined weight of the child and the child LATCH anchorage system to attach the restraint is 65 lbs (29.5 kg).
Page 215 SAFETY Frequently Asked Questions About Installing Child Restraints With LATCH Can the rear-facing child restraint touch the The child seat may touch the back of the back of the front passenger seat? front passenger seat if the child restraint manufacturer also allows contact. See your child restraint owner’s manual for more information.
Page 216 214 SAFETY Locating The Upper Tether Anchorages There are tether strap anchorages behind each rear seating position located on the back of the seat. To access them, pull the carpeted floor panel away from the seat back, this will expose the top tether strap anchorages.
Page 217 SAFETY Center Seat LATCH WARNING! • Do not install a child restraint in the center position using the LATCH system. This position is not ap- proved for installing child seats using the LATCH attachments. You must use the seat belt and tether anchor to install a child seat in the center seating position.
Page 218 216 SAFETY 1. Loosen the adjusters on the lower straps and on the tether strap of the child seat so that you can more easily attach the hooks or connectors to the vehicle anchor- ages. 2. Place the child seat between the lower anchorages for that seating position.
Page 219 SAFETY 6. Test that the child restraint is installed tightly by pulling WARNING! (Continued) back and forth on the child seat at the belt path. It should child could be badly injured or killed. Follow the child not move more than 1 inch (25.4 mm) in any direction. restraint manufacturer’s directions exactly when in- How To Stow An Unused Switchable-ALR (ALR) stalling an infant or child restraint.
Page 220 218 SAFETY The seat belts in the passenger seating positions are Lap/Shoulder Belt Systems For Installing Child equipped with a Switchable Automatic Locking Retractor Restraints In This Vehicle (ALR) that is designed to keep the lap portion of the seat belt tight around the child restraint so that it is not necessary to use a locking clip.
Page 221 SAFETY Frequently Asked Questions About Installing Child Restraints With Seat Belts Can the rear-facing child restraint touch the Contact between the front passenger seat and back of the front passenger seat? the child restraint is allowed, if the child re- straint manufacturer also allows contact.
Page 222 220 SAFETY 5. To lock the seat belt, pull down on the shoulder part of Any seat belt system will loosen with time, so check the the belt until you have pulled all the seat belt webbing belt occasionally, and pull it tight if necessary. out of the retractor.
Page 223 SAFETY You may need to move the seat forward to provide better access to the tether anchorage. If there is no top tether anchorage for that seating position, move the child restraint to another position in the vehicle if one is available.
Page 224: Transporting Pets
222 SAFETY 5. Attach the tether strap hook of the child restraint to the WARNING! (Continued) top tether anchorage as shown in the diagram. • An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child.
Page 225: Safety Tips
SAFETY SAFETY TIPS Exhaust Gas Transporting Passengers WARNING! NEVER TRANSPORT PASSENGERS IN THE CARGO Exhaust gases can injure or kill. They contain carbon AREA. monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can even- WARNING! tually poison you.
Page 226: Safety Checks You Should Make Inside The Vehicle
224 SAFETY vehicle, or when the underside or rear of the vehicle is have the system inspected at your authorized dealer as damaged, have a competent mechanic inspect the complete soon as possible. After the bulb check, this light will exhaust system and adjacent body areas for broken, dam- illuminate with a single chime when a fault with the Air aged, deteriorated, or mispositioned parts.
Page 227 SAFETY WARNING! WARNING! (Continued) depress the accelerator, the brake, and the clutch pedal An improperly attached, damaged, folded, or stacked (if present) to check for interference. If your floor mat floor mat, or damaged floor mat fasteners may cause interferes with the operation of any pedal, or is not your floor mat to interfere with the accelerator, brake, secure to the floor, remove the floor mat from the or clutch pedals and cause a loss of vehicle control.
Page 228: Periodic Safety Checks You Should Make Outside The Vehicle
226 SAFETY Door Latches WARNING! (Continued) Check for proper closing, latching, and locking. • It is recommended to only use mild soap and water to clean your floor mats. After cleaning, always check Fluid Leaks your floor mat has been properly installed and is Check area under the vehicle after overnight parking for secured to your vehicle using the floor mat fasteners fuel, coolant, oil, or other fluid leaks.
Page 229 SAFETY WARNING! To prevent SERIOUS INJURY or DEATH: • ALWAYS remove any “Track-Use” equipment before driving on public roads. • ALWAYS properly use your three-point seat belts when driving on public roads. • In a collision, you and your passengers can suffer much greater injuries if you are not properly buckled up.
Page 231 STARTING AND OPERATING CONTENTS STARTING THE ENGINE ....232 ▫ AutoStick ......247 ▫...
Page 232 230 STARTING AND OPERATING ▫ Adaptive Cruise Control (ACC) Operation ..260 PARKSENSE REAR PARK ASSIST — IF EQUIPPED ......277 ▫...
Page 233 STARTING AND OPERATING 231 PARKSENSE ACTIVE PARK ASSIST SYSTEM — VEHICLE LOADING .....324 IF EQUIPPED ......294 ▫...
Page 234: Starting The Engine
232 STARTING AND OPERATING STARTING THE ENGINE WARNING! (Continued) Before starting your vehicle, adjust your seat, adjust the ignition of a vehicle equipped with Keyless Enter- inside and outside mirrors, fasten your seat belt, and if N-Go in the ACC or ON/RUN mode. A child could present, instruct all other occupants to buckle their seat operate power windows, other controls, or move the belts.
Page 235: Normal Starting
STARTING AND OPERATING 233 To Turn Off The Engine Using ENGINE START/STOP CAUTION! (Continued) Button • Shift into or out of REVERSE only after the vehicle 1. Place the gear selector in PARK, then push and release has come to a complete stop and the engine is at idle the ENGINE START/STOP button.
Page 236: If Engine Fails To Start
234 STARTING AND OPERATING NOTE: The system will automatically time out and the If Engine Fails To Start ignition will cycle to the OFF mode after 30 minutes of inactivity if the ignition is left in the ACC or RUN (engine WARNING! not running) mode and the transmission is in PARK.
Page 237: After Starting
STARTING AND OPERATING 235 • Drive with the engine speed less than 3,500 RPM. After Starting The idle speed is controlled automatically, and it will • Maintain vehicle speed below 55 mph (88 km/h) and decrease as the engine warms up. observe local speed limits.
Page 238: Parking Brake
236 STARTING AND OPERATING For the first 1500 miles (2414 km): • Do not participate in track events, sport driving schools, or similar activities during the first 1500 mi (2414 km). NOTE: Check engine oil with every refueling and add if necessary.
Page 239 STARTING AND OPERATING 237 When parking on a hill, it is important to turn the front WARNING! (Continued) wheels toward the curb on a downhill grade and away • When leaving the vehicle, always make sure the from the curb on an uphill grade. Apply the parking brake keyless ignition node is in the OFF mode, remove the before placing the gear selector in PARK, otherwise the key fob from the vehicle and lock the vehicle.
Page 240: Automatic Transmission
238 STARTING AND OPERATING CAUTION! WARNING! (Continued) indicates PARK (P) without blinking. Ensure that the If the Brake Warning Light remains on with the park- vehicle is completely stopped, and the PARK posi- ing brake released, a brake system malfunction is tion is properly indicated, before exiting the vehicle.
Page 241: Ignition Park Interlock
STARTING AND OPERATING 239 WARNING! (Continued) CAUTION! (Continued) • When exiting the vehicle, always make sure the • Do not shift between PARK, REVERSE, NEUTRAL, ignition is in the OFF mode, remove the key fob from or DRIVE when the engine is above idle speed. •...
Page 242: Brake/Transmission Shift Interlock System
240 STARTING AND OPERATING Brake/Transmission Shift Interlock System This vehicle is equipped with a Brake Transmission Shift Interlock system (BTSI) that holds the transmission gear selector in PARK unless the brakes are applied. To shift the transmission out of PARK, the engine must be running and the brake pedal must be pressed.
Page 243: Eight-Speed Automatic Transmission
STARTING AND OPERATING 241 • Some ECO mode functions may be temporarily inhib- NOTE: In the event of a mismatch between the gear ited based on temperature and other factors. selector position and the actual transmission gear (for example, driver selects PARK while driving), the position NOTE: ECO mode is only available in AUTO, SPORT or indicator will blink continuously until the selector is re- TRACK mode.
Page 244 242 STARTING AND OPERATING (+/-), will manually select the transmission gear, and will Gear Ranges display the current gear in the instrument cluster. Do not depress the accelerator pedal when shifting from PARK or NEUTRAL into another gear range. NOTE: If the gear selector cannot be moved to the PARK, REVERSE, or NEUTRAL position (when pushed forward) NOTE: After selecting any gear range, wait a moment to it is probably in the AutoStick (+/-) position (beside the...
Page 245 STARTING AND OPERATING 243 • Turn the ignition OFF. WARNING! (Continued) • Remove the key fob from the vehicle. vehicle could accelerate quickly forward or in re- verse. You could lose control of the vehicle and hit WARNING! someone or something. Only shift into gear when the engine is idling normally and your foot is firmly •...
Page 246 244 STARTING AND OPERATING • Look at the transmission gear position display and WARNING! (Continued) verify that it indicates the PARK position (P), and is not touch the parking brake, brake pedal or the trans- blinking. mission gear selector. • With brake pedal released, verify that the gear selector •...
Page 247 STARTING AND OPERATING 245 When frequent transmission shifting occurs (such as when WARNING! operating the vehicle under heavy loading conditions, in hilly terrain, traveling into strong head winds, or while Do not coast in NEUTRAL and never turn off the towing a heavy trailer), select TOW mode (refer to “Selec- ignition to coast down a hill.
Page 248 246 STARTING AND OPERATING Transmission Limp Home Mode 3. Push and hold the ignition switch until the engine turns OFF. Transmission function is monitored electronically for ab- normal conditions. If a condition is detected that could 4. Wait approximately 30 seconds. result in transmission damage, Transmission Limp Home 5.
Page 249: Autostick
STARTING AND OPERATING 247 rearward (+) (or tapping the (+) shift paddle) will com- AutoStick mand an upshift. AutoStick is a driver-interactive transmission feature pro- viding manual shift control, giving you more control of the NOTE: The shift paddles may be disabled (or re-enabled, vehicle.
Page 250: Four-Wheel Drive Operation
248 STARTING AND OPERATING • The system will ignore attempts to upshift at too low of FOUR-WHEEL DRIVE OPERATION a vehicle speed. Selec-Track — If Equipped (SRT) • Holding the (-) paddle depressed, or holding the gear Description selector in the (-) position, will downshift the transmis- Selec-Track combines the capabilities of the vehicle control sion to the lowest gear possible at the current speed.
Page 251 STARTING AND OPERATING 249 Selec-Track consists of the following positions: Custom • Sport – Dry weather, on-road calibration. Performance This mode allows the driver to create a custom vehicle based tuning that provides a rear wheel drive feel but configuration that is saved for quick selection of favorite with improved handling and acceleration over a two- settings.
Page 252 250 STARTING AND OPERATING • Track Mode (Available in terrain positions AUTO, • Launch Control is not available within the first 500 miles TRACK and CUSTOM.) — Provides a full firm suspen- (805 km) of engine break-in. sion for an aggressive track experience. •...
Page 253 STARTING AND OPERATING 251 2. Press the “Launch RPM Set-Up” button on the touch- Launch control will be active until the vehicle reaches screen. This screen will allow you to adjust your launch 62 mph (100 km/h), at which point the Electronic Stability RPM’s for optimum launch/traction.
Page 254 252 STARTING AND OPERATING • It is recommended that each track outing should end Guidelines For Track Use with a minimum of one cool down lap using minimal NOTE: Because of the extreme conditions encountered braking. during track use, any damage or wear associated with •...
Page 255 STARTING AND OPERATING 253 Cold and adjusting based on ambient & track conditions is 5. There should be a thin, ash layer when inspecting the recommended. Tire pressure can be monitored via the pads installed in the caliper. Having the ash layer go instrument cluster display and can assist with adjustments.
Page 256: Fuel Saver Technology - If Equipped
254 STARTING AND OPERATING Alternate electric power steering efforts can be selected FUEL SAVER TECHNOLOGY — IF EQUIPPED through the Uconnect System. Refer to ”Customer Pro- This feature offers improved fuel economy by shutting off grammable Features” within “Uconnect Settings” in “Mul- four of the engine’s eight cylinders during light load and timedia”...
Page 257: Speed Control - If Equipped
STARTING AND OPERATING 255 NOTE: In order to ensure proper operation, the Speed SPEED CONTROL — IF EQUIPPED Control System has been designed to shut down if multiple When engaged, the Speed Control takes over accelerator Speed Control functions are operated at the same time. If operations at speeds greater than 25 mph (40 km/h).
Page 258: To Set A Desired Speed
256 STARTING AND OPERATING Know Your Instrument Panel” for more information. The WARNING! speed increment shown is dependant on the chosen speed unit of U.S. (mph) or Metric (km/h): Leaving the Speed Control system on when not in use is dangerous. You could accidentally set the system or U.S.
Page 259: To Accelerate For Passing
STARTING AND OPERATING 257 Know Your Instrument Panel” for more information. The Using Speed Control On Hills speed decrement shown is dependant on the chosen speed The transmission may downshift on hills to maintain the unit of U.S. (mph) or Metric (km/h): vehicle set speed.
Page 260: To Deactivate
258 STARTING AND OPERATING NOTE: To Deactivate • If the sensor does not detect a vehicle ahead of you, ACC A soft tap on the brake pedal, pushing the CANC button, will maintain a fixed set speed. or normal brake pressure while slowing the vehicle will deactivate the Speed Control without erasing the set speed •...
Page 261 STARTING AND OPERATING 259 WARNING! WARNING! (Continued) • Will bring the vehicle to a complete stop while • Adaptive Cruise Control (ACC) is a convenience following a target vehicle and hold the vehicle for system. It is not a substitute for active driving 2 seconds in the stop position.
Page 262: Adaptive Cruise Control (Acc) Operation
260 STARTING AND OPERATING Adaptive Cruise Control (ACC) Operation Activating Adaptive Cruise Control (ACC) The Speed Control buttons (located on the right side of the You can only engage ACC if the vehicle speed is above 0 mph (0 km/h). steering wheel) operates the ACC system.
Page 263: To Activate/Deactivate
STARTING AND OPERATING 261 To Activate/Deactivate Push and release the Adaptive Cruise Control (ACC) on/off button. The ACC menu in the instrument cluster displays “ACC Ready.” Adaptive Cruise Control Off WARNING! Leaving the Adaptive Cruise Control (ACC) system on when not in use is dangerous. You could accidentally Adaptive Cruise Control Ready set the system or cause it to go faster than you want.
Page 264: To Cancel
262 STARTING AND OPERATING • The gear selector is removed from the DRIVE position. If the system is set when the vehicle speed is below 20 mph (32 km/h), the set speed shall be defaulted to 20 mph • The Electronic Stability Control/Traction Control Sys- (32 km/h).
Page 265: To Resume
STARTING AND OPERATING 263 To Resume To Vary The Speed Setting If there is a set speed in memory push the RES (resume) To Increase Speed button and then remove your foot from the accelerator While ACC is set, you can increase the set speed by pedal.
Page 266 264 STARTING AND OPERATING • If the button is continually pushed, the set speed will Metric Speed (km/h) continue to increase in 10 km/h increments until the • Pushing the SET (-) button once will result in a 1 km/h button is released.
Page 267: Setting The Following Distance In Acc
STARTING AND OPERATING 265 • The ACC system maintains set speed when driving up hill and down hill. However, a slight speed change on moderate hills is normal. In addition, downshifting may occur while climbing uphill or descending downhill. This is normal operation and necessary to maintain set speed.
Page 268 266 STARTING AND OPERATING To increase the distance setting, push the Distance Setting — Increase button and release. Each time the button is pushed, the distance setting increases by one bar (longer). To decrease the distance setting, push the Distance Setting —...
Page 269: Overtake Aid
STARTING AND OPERATING 267 The maximum braking applied by ACC is limited; how- NOTE: The “Brake!” Screen in the instrument cluster ever, the driver can always apply the brakes manually, if display is a warning for the driver to take action and does necessary.
Page 270: Adaptive Cruise Control (Acc) Menu
268 STARTING AND OPERATING While ACC with Stop is holding your vehicle at a stand- Adaptive Cruise Control Off still, if the driver seatbelt is unbuckled or the driver door is When ACC is deactivated, the display will read “Adaptive opened, the ACC with Stop system will cancel and the Cruise Control Off.”...
Page 271: Display Warnings And Maintenance
STARTING AND OPERATING 269 • The instrument cluster display will return to the last NOTE: If the “ACC/FCW Unavailable Wipe Front Radar display selected after five seconds of no ACC display Sensor” warning is active Normal (Fixed Speed) Cruise activity Control is still available.
Page 272 270 STARTING AND OPERATING When the condition that deactivated the system is no display “ACC/FCW Limited Functionality Clean Front longer present, the system will return to the “Adaptive Windshield” and the system will have degraded perfor- Cruise Control Off” state and will resume function by mance.
Page 273: Precautions While Driving With Acc
STARTING AND OPERATING 271 Service ACC/FCW Warning Offset Driving If the system turns off, and the instrument cluster displays ACC may not detect a vehicle in the same lane that is offset “ACC/FCW Unavailable Service Required” or “Cruise/ from your direct line of travel, or a vehicle merging in from FCW Unavailable Service Required”, there may be an a side lane.
Page 274 272 STARTING AND OPERATING Turns And Bends Using ACC On Hills When driving on a curve with ACC engaged, the system When driving on hills, ACC may not detect a vehicle in may decrease the vehicle speed and acceleration for stabil- your lane.
Page 275 STARTING AND OPERATING 273 Lane Changing Narrow Vehicles ACC may not detect a vehicle until it is completely in the Some narrow vehicles traveling near the outer edges of the lane in which you are traveling. In the illustration shown, lane or edging into the lane are not detected until they have ACC has not yet detected the vehicle changing lanes and it moved fully into the lane.
Page 276: General Information
274 STARTING AND OPERATING Stationary Objects And Vehicles General Information ACC does not react to stationary objects and stationary The following regulatory statement applies to all Radio vehicles. For example, ACC will not react in situations Frequency (RF) devices equipped in this vehicle: where the vehicle you are following exits your lane and the This device complies with Part 15 of the FCC Rules and vehicle ahead is stopped in your lane.
Page 277 STARTING AND OPERATING 275 To change between the different control modes, push the will appear indicating what speed was set. This light will Adaptive Cruise Control (ACC) on/off button which turns turn on when the system is turned on via the on/off the ACC and the Normal (Fixed Speed) Cruise Control off.
Page 278 276 STARTING AND OPERATING • If the button is continually pushed, the set speed will Metric Speed (km/h) continue to decrease in 5 mph decrements until the • Pushing the SET (+) button once will result in a 1 km/h button is released.
Page 279: Parksense Rear Park Assist - If Equipped
STARTING AND OPERATING 277 • The braking temperature exceeds normal range (over- PARKSENSE REAR PARK ASSIST — IF EQUIPPED heated). The ParkSense Rear Park Assist system provides visual and • The gear selector is removed from the DRIVE position. audible indications of the distance between the rear fascia and a detected obstacle when backing up, e.g.
Page 280: Parksense Sensors
278 STARTING AND OPERATING • The automatic braking function may not be applied fast ParkSense will retain the last system state (enabled or enough for obstacles that move toward the rear of the disabled) from the last ignition cycle when the ignition is vehicle from the left and/or right sides.
Page 281: Parksense Warning Display
STARTING AND OPERATING 279 ParkSense Warning Display The ParkSense Warning screen will only be displayed if Sound and Display is selected from the Customer - Pro- grammable Features section of the Uconnect System. Refer to Uconnect Settings” in “Multimedia” for further infor- mation.
Page 282 280 STARTING AND OPERATING Single 1/2 Second Tone Slow Tone Slow Tone Fast Tone...
Page 283 STARTING AND OPERATING 281 Fast Tone Continuous Tone...
Page 284 282 STARTING AND OPERATING The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting an obstacle: WARNING ALERTS Rear Dis- Greater...
Page 285: Enabling And Disabling Parksense
STARTING AND OPERATING 283 Adjustable Chime Volume Settings The ParkSense switch LED will be on when ParkSense is disabled or requires service. The ParkSense switch LED Rear chime volume settings can be selected from the will be off when the system is enabled. If the ParkSense Customer-Programmable Features section of the Uconnect switch is pushed, and the system requires service, the System, refer to “Uconnect Settings”...
Page 286: Cleaning The Parksense System
284 STARTING AND OPERATING • When you move the gear selector to the REVERSE is clean and clear of snow, ice, mud, dirt or other obstruc- tion and then cycle the ignition. If the message continues to position and ParkSense is turned off, the instrument appear, see an authorized dealer.
Page 287: Parksense Front And Rear Park Assist - If Equipped
STARTING AND OPERATING 285 liftgate could provide a false indication that an obstacle CAUTION! is behind the vehicle. • ParkSense is only a parking aid and it is unable to WARNING! recognize every obstacle, including small obstacles. Parking curbs might be temporarily detected or not •...
Page 288 286 STARTING AND OPERATING • ParkSense will retain its last known configuration state NOTE: for the automatic braking function through ignition • The driver can override the automatic braking function cycles. by pressing the gas pedal, turning ParkSense off via ParkSense switch, or changing the gear while the auto- The automatic braking function is intended to assist the matic brakes are being applied.
Page 289: Parksense Sensors
STARTING AND OPERATING 287 the vehicle speed is increased to approximately 7 mph ParkSense Warning Display (11 km/h) or above. A display warning will appear in the The ParkSense Warning screen will only be displayed if instrument cluster display indicating the vehicle is above Sound and Display is selected from the Customer Pro- ParkSense operating speed.
Page 290 288 STARTING AND OPERATING Park Assist Ready Single 1/2 Second Tone The system will indicate a detected obstacle by showing a single arc in the left and/or right front or rear regions based on the object’s distance and location relative to the vehicle.
Page 291 STARTING AND OPERATING 289 Slow Tone For Rear Only Fast Tone Fast Tone For Rear Only Continuous Tone...
Page 292 290 STARTING AND OPERATING The vehicle is close to the obstacle when the instrument cluster display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert operation when the system is detecting an obstacle: WARNING ALERTS FOR REAR Rear Dis- Greater...
Page 293: Enabling And Disabling Parksense
STARTING AND OPERATING 291 WARNING ALERTS FOR FRONT Front Distance Greater than 47 47-39 inches 39-25 inches 25-12 inches Less than 12 (inches/cm) inches (120 cm) (120-100 cm) (100-65 cm) (65-30 cm) inches (30 cm) Audible Alert None None None Fast Continuous Chime...
Page 294: Service The Parksense Park Assist System
292 STARTING AND OPERATING the “PARKSENSE OFF” message for approximately five selector is moved to REVERSE and the system has detected seconds. Refer to “Instrument Cluster Display” in “Getting a faulted condition, the instrument cluster display will To Know Your Instrument Panel” for further information. display a PARKSENSE UNAVAILABLE WIPE REAR SEN- When the gear selector is moved to REVERSE and the SORS , PARKSENSE UNAVAILABLE WIPE FRONT SEN-...
Page 295: Cleaning The Parksense System
STARTING AND OPERATING 293 snow, ice, mud, dirt or other obstruction and then cycle the • When you move the gear selector to the REVERSE ignition. If the message continues to appear see your position and ParkSense is turned off, the instrument authorized dealer.
Page 296: Parksense Active Park Assist System - If Equipped
294 STARTING AND OPERATING WARNING! CAUTION! • Drivers must be careful when backing up even when • ParkSense is only a parking aid and it is unable to recognize every obstacle, including small obstacles. using ParkSense. Always check carefully behind Parking curbs might be temporarily detected or not your vehicle, look behind you, and be sure to check detected at all.
Page 297: Enabling And Disabling The Parksense Active Park Assist System
STARTING AND OPERATING 295 a parallel or a perpendicular parking space on either side vehicle calibration to account for differences such as (i.e., driver side or passenger side). over or under inflated tires and new tires. NOTE: Enabling And Disabling The ParkSense Active Park Assist System •...
Page 298 296 STARTING AND OPERATING The ParkSense Active Park Assist system will turn off The ParkSense Active Park Assist system will only operate automatically for any of the following conditions: and search for a parking space when the following condi- tions are present: •...
Page 299: Parallel Parking Space Assistance Operation/Display
STARTING AND OPERATING 297 • When seeking for a parking space, the driver should Parallel Parking Space Assistance Operation/ drive as parallel or perpendicular (depending on the Display type of maneuver) to other vehicles as possible. When the ParkSense Active Park Assist system is enabled the “Active ParkSense Searching - Push OK to Switch to •...
Page 300 298 STARTING AND OPERATING When an available parking space has been found, and the Once the vehicle is in position, you will be instructed to vehicle is not in position, you will be instructed to move stop the vehicle’s movement and remove your hands from forward to position the vehicle for a parallel parking the steering wheel.
Page 301 STARTING AND OPERATING 299 Once the vehicle is at a standstill with your hands removed When the driver places the gear selector into the REVERSE from the steering wheel, you will be instructed to place the position, the system may instruct the driver to wait for gear selector into the REVERSE position.
Page 302 300 STARTING AND OPERATING • When the system instructs the driver to remove their The system will then instruct the driver to check their surroundings and move backward. hands from the steering wheel, the driver should check their surroundings and begin to back up slowly. •...
Page 303 STARTING AND OPERATING 301 When the vehicle has reached the end of its backward Once the vehicle is in a standstill condition, the driver will movement, the system will instruct the driver to check be instructed to place the gear selector into the DRIVE their surroundings and stop the vehicle’s movement.
Page 304 302 STARTING AND OPERATING When the driver places the gear selector into the DRIVE The system will then instruct the driver to check their position, the system may instruct the driver to wait for surroundings and move forward. steering to complete. Check Surroundings —...
Page 305 STARTING AND OPERATING 303 When the vehicle has reached the end of its forward Once the vehicle is in a standstill condition, the driver will movement, the system will instruct the driver to check be instructed to place the gear selector into the REVERSE their surroundings and stop the vehicle’s movement.
Page 306 304 STARTING AND OPERATING When the driver places the gear selector into the REVERSE The system will then instruct the driver to check their position, the system may instruct the driver to wait for surroundings and move backward. steering to complete. Check Surroundings —...
Page 307: Perpendicular Parking Space Assistance Operation/Display
STARTING AND OPERATING 305 Your vehicle is now in the parallel park position. When the Perpendicular” message will show in the instrument clus- maneuver is complete, the driver will be instructed to ter display. Push the OK button on the left side steering check the vehicle’s parking position.
Page 308 306 STARTING AND OPERATING • The feature will only indicate the last detected parking NOTE: space (example: if passing multiple available parking • When searching for a parking space, use the turn signal spaces, the system will only indicate the last detected indicator to select which side of the vehicle you want to parking space for the maneuver).
Page 309 STARTING AND OPERATING 307 Once the vehicle is in position, you will be instructed to Once the vehicle is at a standstill with your hands removed stop the vehicle’s movement and remove your hands from from the steering wheel, you will be instructed to place the the steering wheel.
Page 310 308 STARTING AND OPERATING When the driver places the gear selector into the REVERSE position, the system may instruct the driver to wait for steering to complete. Check Surroundings — Move Backward NOTE: • It is the driver’s responsibility to use the brake and Check Surroundings —...
Page 311 STARTING AND OPERATING 309 • The ParkSense Active Park Assist system will allow a maximum of six shifts between DRIVE and REVERSE. If the maneuver cannot be completed within six shifts, the system will cancel and the instrument cluster display will instruct the driver to complete the maneuver manu- ally.
Page 312 310 STARTING AND OPERATING Once the vehicle is in a standstill condition, the driver will When the driver places the gear selector into the DRIVE be instructed to place the gear selector into the DRIVE position, the system may instruct the driver to wait for position.
Page 313 STARTING AND OPERATING 311 The system will then instruct the driver to check their surroundings and move forward. Check Surroundings — STOP NOTE: It is the driver’s responsibility to use the brake and stop the vehicle. The driver should check their surround- Check Surroundings —...
Page 314 312 STARTING AND OPERATING Once the vehicle is in a standstill condition, the driver will When the driver places the gear selector into the REVERSE be instructed to place the gear selector into the REVERSE position, the system may instruct the driver to wait for position.
Page 315 STARTING AND OPERATING 313 The system will then instruct the driver to check their surroundings and move backward. Active ParkSense Complete — Check Parking Position WARNING! Check Surroundings — Move Backward Your vehicle is now in the perpendicular park position. •...
Page 316: Lanesense - If Equipped
314 STARTING AND OPERATING WARNING! (Continued) CAUTION! (Continued) continue to pay attention to your surroundings. Fail- Obstacles located above or below the sensors will ure to do so can result in serious injury or death. not be detected when they are in close proximity. •...
Page 317: Turning Lanesense On Or Off
STARTING AND OPERATING 315 the LaneSense system provides a visual warning through The LaneSense button is located on the switch panel below the instrument cluster display to prompt the driver to the Uconnect display. remain within the lane boundaries. The driver may manually override the haptic warning by applying torque into the steering wheel at any time.
Page 318: Lanesense Warning Message
316 STARTING AND OPERATING Premium Instrument Cluster Display When the LaneSense system is on; the lane lines are gray when both of the lane boundaries have not been detected and the LaneSense telltale is solid white. LaneSense On Message To turn the LaneSense system off, push the LaneSense button once (LED turns on).
Page 319 STARTING AND OPERATING 317 • When the LaneSense system senses the lane has been Left Lane Departure — Both Lanes Detected approached and is in a lane departure situation, the left • When the LaneSense system is on, the lane lines turn thick lane line flashes yellow (on/off), the left thin line from gray to white to indicate that both of the lane remains solid yellow and the LaneSense telltale...
Page 320 318 STARTING AND OPERATING this time torque is applied to the steering wheel in the The LaneSense telltale changes from solid green to opposite direction of the lane boundary. solid yellow. At this time torque is applied to the • For example: If approaching the left side of the lane the steering wheel in the opposite direction of the lane steering wheel will turn to the right.
Page 321: Changing Lanesense Status
STARTING AND OPERATING 319 the top of the screen. After five seconds this note will Changing LaneSense Status disappear. The ParkView camera is located on the rear of The LaneSense system has settings to adjust the intensity of the vehicle above the rear license plate. the torque warning and the warning zone sensitivity (early/late) that you can configure through the Uconnect When the vehicle is shifted out of REVERSE (with camera...
Page 322 320 STARTING AND OPERATING rear of the vehicle. The following table shows the approxi- mate distances for each zone: Zone Distance To The Rear Of The Vehicle 0 - 1 ft (0 - 30 cm) Yellow 1 ft - 6.5 ft (30 cm - 2 m) Green 6.5 ft or greater (2 m or greater) WARNING!
Page 323: Refueling The Vehicle
STARTING AND OPERATING 321 Rear Camera — Viewing At Speed When the vehicle is in park, neutral or drive, the Rear View Camera can be activated with the “Rear View Camera” button in the Controls menu. This feature allows the customer to monitor the area directly behind the vehicle (or trailer, if equipped) for up to ten seconds while at speed.
Page 324 322 STARTING AND OPERATING 6. Wait five seconds before removing the fuel nozzle to allow fuel to drain from nozzle. 7. Remove the fuel nozzle and close the fuel door. Emergency Gas Can Refueling Most gas cans will not open the flapper doors. A funnel is provided to open the flapper doors to allow emergency refueling with a gas can.
Page 325: Emergency Fuel Filler Door Release
STARTING AND OPERATING 323 4. Remove the storage bin. WARNING! (Continued) 5. Pull the release cable to open the fuel door, push the • Never add fuel when the engine is running. This is release cable back to the home position to re-seat the fuel in violation of most state and federal fire regulations door latch to the closed position.
Page 326: Vehicle Loading
324 STARTING AND OPERATING Gross Axle Weight Rating (GAWR) VEHICLE LOADING The GAWR is the maximum permissible load on the front Certification Label and rear axles. The load must be distributed in the cargo As required by National Highway Traffic Safety Adminis- area so that the GAWR of each axle is not exceeded.
Page 327: Trailer Towing
STARTING AND OPERATING 325 Curb Weight Improper weight distributions can have an adverse effect on the way your vehicle steers and handles and the way The curb weight of a vehicle is defined as the total weight the brakes operate. of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded CAUTION!
Page 328: Common Towing Definitions
326 STARTING AND OPERATING Gross Axle Weight Rating (GAWR) Common Towing Definitions The following trailer towing related definitions will assist The GAWR is the maximum capacity of the front and rear you in understanding the following information: axles. Distribute the load over the front and rear axles evenly.
Page 329 STARTING AND OPERATING 327 Trailer Sway Control for a more level ride, offering more consistent steering and brake control thereby enhancing towing safety. The addi- The trailer sway control can be a mechanical telescoping tion of a friction/hydraulic sway control also dampens link that can be installed between the hitch receiver and the sway caused by traffic and crosswinds and contributes trailer tongue that typically provides adjustable friction...
Page 330: Trailer Hitch Classification
328 STARTING AND OPERATING Trailer Hitch Classification The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Trailer Hitch Classification Definitions Class Max.
Page 331: Trailer Hitch Receiver Cover Removal
STARTING AND OPERATING 329 NOTE: 1. Turn the two locking retainers located at the bottom of the hitch receiver cover a 1/4 turn counterclockwise. • The trailer tongue weight must be considered as part of the combined weight of occupants and cargo, and NOTE: Use a suitable tool such as a coin in the slot of the should never exceed the weight referenced on the Tire locking retainer if needed for added leverage.
Page 332 330 STARTING AND OPERATING 2. Pull the bottom of the cover outward (towards you). Hitch Receiver Cover Removal To reinstall the hitch receiver cover after towing repeat the Hitch Receiver Cover procedure in reverse order. 3. Lower back down to disengage the tabs located at the top of the hitch receiver cover and then pull outwards to NOTE: Be sure to engage all tabs of the hitch receiver cover remove.
Page 333: Trailer And Tongue Weight
STARTING AND OPERATING 331 NOTE: Remember that everything put into or on the Trailer And Tongue Weight trailer adds to the load on your vehicle. Also, additional Never exceed the maximum tongue weight stamped on factory-installed options or dealer-installed options must your bumper or trailer hitch.
Page 334 332 STARTING AND OPERATING Maintenance” for the proper maintenance intervals. When WARNING! (Continued) towing a trailer, never exceed the GAWR or GCWR ratings. • Vehicles with trailers should not be parked on a grade. When parking, apply the parking brake on the WARNING! tow vehicle.
Page 335 STARTING AND OPERATING 333 Towing Requirements — Tires • An electronically actuated trailer brake controller is required when towing a trailer with electronically actu- • Do not attempt to tow a trailer while using a compact ated brakes. When towing a trailer equipped with a spare tire.
Page 336 334 STARTING AND OPERATING NOTE: CAUTION! (Continued) • Disconnect trailer wiring connector from the vehicle be of adequate capacity. Failure to do this could lead to before launching a boat (or any other device plugged accelerated brake lining wear, higher brake pedal into vehicle’s electrical connect) into water.
Page 337: Towing Tips
STARTING AND OPERATING 335 Automatic Transmission Select the DRIVE range when towing. The transmission controls include a drive strategy to avoid frequent shifting when towing. However, if frequent shifting does occur while in DRIVE, select TOW mode, or use the AutoStick shift control to manually select a lower gear.
Page 338: Recreational Towing
336 STARTING AND OPERATING • To prevent excess heat generation, avoid continuous RECREATIONAL TOWING driving at high RPM. Reduce vehicle speed as necessary Recreational towing is not allowed. to avoid extended driving at high RPM. Return to a higher gear or vehicle speed when grade and road CAUTION! conditions allow.
Page 339: Driving Through Water
STARTING AND OPERATING 337 • Maintain sufficient distance between your vehicle and WARNING! the vehicle in front of you to avoid a collision in a sudden stop. Rapid acceleration on slippery surfaces is dangerous. Unequal traction can cause sudden pulling of the front Driving Through Water wheels.
Page 340 338 STARTING AND OPERATING Shallow Standing Water CAUTION! (Continued) Although your vehicle is capable of driving through shal- water that is deeper than the bottom of the tire rims low standing water, consider the following Cautions and mounted on the vehicle. Warnings before doing so.
Page 341 IN CASE OF EMERGENCY CONTENTS HAZARD WARNING FLASHERS ... .340 ▫ Road Tire Installation ....364 ASSIST AND SOS MIRROR —...
Page 342: Hazard Warning Flashers
340 IN CASE OF EMERGENCY HAZARD WARNING FLASHERS ASSIST AND SOS MIRROR — IF EQUIPPED The Hazard Warning flasher switch is located on the switch bank just above the climate controls. Push the switch to turn on the Hazard Warning flasher.
Page 343 IN CASE OF EMERGENCY 341 • SiriusXM Guardian Customer Care – In-vehicle support WARNING! (Continued) for SiriusXM Guardian. related to the use of the features and applications in this • Vehicle Customer Care – Total support for all other vehicle. Only use the features and applications when it vehicle issues.
Page 344 342 IN CASE OF EMERGENCY 4. You should be able to speak with the SOS operator will attempt to remain connected with the SOS operator through the vehicle audio system to determine if addi- until the SOS operator terminates the connection. tional help is needed.
Page 345 IN CASE OF EMERGENCY 343 If the SOS Call system detects a malfunction, any of the WARNING! (Continued) following may occur at the time the malfunction is de- initiate an emergency call. To avoid interference that tected, and at the beginning of each ignition cycle: can cause the SOS Call system to fail, never add •...
Page 346 344 IN CASE OF EMERGENCY Even if the SOS Call system is fully functional, factors WARNING! beyond FCA US LLC’s control may prevent or stop the SOS Call system operation. These include, but are not limited ALWAYS obey traffic laws and pay attention to the to, the following factors: road.
Page 347: Bulb Replacement
IN CASE OF EMERGENCY 345 This device may not cause harmful interference, and (2) CAUTION! this device must accept any interference received, includ- ing interference that may cause undesired operation. To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. NOTE: Changes or modifications not expressly approved Apply the solution onto a clean cloth and wipe the by the party responsible for compliance could void the...
Page 348 346 IN CASE OF EMERGENCY Exterior Bulbs Bulb Number Premium Headlamps (Low/High Beam) D3S (Serviced At Authorized Dealer) Premium Park/Turn Signal Lamp LED - (Service At Authorized Dealer) Premium Daytime Running Lamp (DRL) LED - (Service At Authorized Dealer) Premium Front Fog Lamps LED - (Service At Authorized Dealer) Premium Front Side Marker LED - (Service At Authorized Dealer)
Page 349: Bulb Replacement
IN CASE OF EMERGENCY 347 Front Turn Signal Lamp Bulb Replacement The front turn signal lamps are LEDs. See your authorized High Intensity Discharge Headlamps (HID) — If dealer for service. Equipped The headlamps are a type of high voltage discharge tube. Front Fog Lamps High voltage can remain in the circuit even with the Please see your authorized dealer for service.
Page 350 348 IN CASE OF EMERGENCY 3. Grasp the tail lamp and pull firmly rearward to disen- Rear Liftgate Mounted Tail Lamp gage the lamp from the aperture panel. 4. Twist socket counter clockwise and remove from lamp. Rear Liftgate Tail Lamps 1.
Page 351 IN CASE OF EMERGENCY 349 Liftgate Lower Trim Rear Of Liftgate Tail Lamp 3. Continue removing the trim. 1 — Auxiliary LED Tail Connector – Do Not Remove 2 — Backup Bulb Socket 4. Disconnect the two trim panel lights. 5.
Page 352: Fuses
350 IN CASE OF EMERGENCY Center High-Mounted Stop Lamp (CHMSL) FUSES The center high mounted stop lamp is an LED. Service at WARNING! an authorized dealer. • When replacing a blown fuse, always use an appro- priate replacement fuse with the same amp rating as the original fuse.
Page 353: General Information
IN CASE OF EMERGENCY 351 General Information Underhood Fuses The fuses protect electrical systems against excessive current. The Power Distribution Center is located in the engine compartment near the battery. This center contains car- When a device does not work, you must check the fuse tridge fuses, micro fuses, relays, and circuit breakers.
Page 354 352 IN CASE OF EMERGENCY Cavity Cartridge Fuse Micro Fuse Description 60 Amp Yellow – Radiator Fan 40 Amp Green – Compressor for Air Suspension — If Equipped 40 Amp Green – Anti-lock Brakes/Electronic Stability Control Pump 30 Amp Pink –...
Page 355 IN CASE OF EMERGENCY 353 Cavity Cartridge Fuse Micro Fuse Description 20 Amp Blue – Trailer Tow Backup Lights — If Equipped 20 Amp Blue – Trailer Tow Parking Lights — If Equipped 30 Amp Pink – Trailer Tow Receptacle — If Equipped 30 Amp Pink –...
Page 356 354 IN CASE OF EMERGENCY Cavity Cartridge Fuse Micro Fuse Description – 15 Amp Blue Additional Content (Diesel engine only) – 20 Amp Yellow NOX Sensor – 15 Amp Blue HID Headlamps LH — If Equipped – 10 Amp Red Purging Pump (Diesel engine only) –...
Page 357 IN CASE OF EMERGENCY 355 Cavity Cartridge Fuse Micro Fuse Description – 10 Amp Red Drivetrain Control Module/Front Axle Disconnect Module – 10 Amp Red Engine Control Module/Electric Power Steering – 10 Amp Red Universal Garage Door Opener/Compass/Anti-Intrusion Module – 20 Amp Yellow Trailer Tow Right Turn/Stop Lights –...
Page 358 356 IN CASE OF EMERGENCY Cavity Cartridge Fuse Micro Fuse Description – 20 Amp Yellow Rear Heated Seats & Heated Steering Wheel — If Equipped – 20 Amp Yellow Front Heated Seats — If Equipped – 10 Amp Red Climate Control/Driver Assistance Systems Module/ DSRC F100 –...
Page 359: Jacking And Tire Changing
IN CASE OF EMERGENCY 357 JACKING AND TIRE CHANGING Run Flat Tires This vehicle is equipped with “run flat” tires. Run flat tires WARNING! allow the vehicle to be driven approximately 50 miles (80km) at 55 mph (88km/h). Tire service should be ob- •...
Page 360: Jack Location
358 IN CASE OF EMERGENCY Jack Location Spare Tire Stowage The scissor-type jack and tire changing tools are located in The spare tire is stowed under the load floor in the rear the rear cargo area, below the load floor. cargo area and is secured to the body with a special wing nut.
Page 361: Jacking Instructions
IN CASE OF EMERGENCY 359 5. Turn the ignition OFF. WARNING! (Continued) 6. Block both the front and rear of the wheel diagonally • Block the wheel diagonally opposite the wheel to be opposite the jacking position. For example, if the right raised.
Page 362 360 IN CASE OF EMERGENCY Jack And Tool Assembly Jack Warning Label CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the Jacking Instructions for this vehicle. 1. Remove the spare tire, jack, and tools from storage. 2.
Page 363 IN CASE OF EMERGENCY 361 4. For the front axle, place the jack on the body flange just behind the front tire as indicated by the triangular lift point symbol on the sill molding. Do not raise the vehicle until you are sure the jack is fully engaged. Front Jacking Location 5.
Page 364 362 IN CASE OF EMERGENCY CAUTION! Do NOT raise the vehicle by the body side sill mold- ing. Be sure the jack is placed in the proper engage- ment location on the inside of the panel. Damage of the vehicle may occur if the procedure is not properly followed.
Page 365 IN CASE OF EMERGENCY 363 8. Position the spare wheel/tire on the vehicle and install WARNING! the lug nuts with the cone-shaped end toward the wheel. Lightly tighten the nuts. To avoid the risk of forcing the vehicle off the jack, do not tighten the wheel nuts fully until the vehicle has CAUTION! been lowered.
Page 366: Road Tire Installation
364 IN CASE OF EMERGENCY WARNING! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided. Have the deflated (flat) tire repaired or replaced immediately.
Page 367: Jump Starting
IN CASE OF EMERGENCY 365 5. After 25 miles (40 km), check the lug nut torque with a Preparations For Jump Start torque wrench to ensure that all lug nuts are properly The battery in your vehicle is located under the passenger’s seated against the wheel.
Page 368: Jump Starting Procedure
366 IN CASE OF EMERGENCY 4. If using another vehicle to jump start the battery, park WARNING! the vehicle within the jumper cables reach, apply the parking brake and make sure the ignition is OFF. • Take care to avoid the radiator cooling fan whenever the hood is raised.
Page 369 IN CASE OF EMERGENCY 367 Connecting The Jumper Cables CAUTION! 1. Connect the positive (+) end of the jumper cable to the Do not run the booster vehicle engine above 2000 rpm remote positive (+) post of the discharged vehicle. since it provides no charging benefit, wastes fuel and 2.
Page 370: Refueling In Emergency
368 IN CASE OF EMERGENCY If frequent jump starting is required to start your vehicle IF YOUR ENGINE OVERHEATS you should have the battery and charging system tested at In any of the following situations, you can reduce the an authorized dealer. potential for overheating by taking the appropriate action.
Page 371: Manual Park Release
IN CASE OF EMERGENCY 369 WARNING! (Continued) WARNING! (Continued) see or hear steam coming from under the hood, do not seat with your foot firmly on the brake pedal when open the hood until the radiator has had time to cool. activating the Manual Park Release.
Page 372 370 IN CASE OF EMERGENCY Manual Park Release Cover Release Latch 3. Press and maintain firm pressure on the brake pedal. 5. While the metal latch is in the open position, simulta- neously pull upwards on the tether strap until the lever 4.
Page 373 IN CASE OF EMERGENCY 371 To Disengage The Manual Park Release Lever: 1. To disengage the Manual Park Release, apply tension upward while pushing the release latch towards the tether to unlock the lever. Released Position CAUTION! Closing the armrest while the Manual Park Release is activated may damage the Manual Park Release Release Latch mechanism, the transmission, and/or the armrest.
Page 374: Freeing A Stuck Vehicle
372 IN CASE OF EMERGENCY NOTE: Shifts between DRIVE and REVERSE can only be achieved at wheel speeds of 5 mph (8 km/h) or less. Whenever the transmission remains in NEUTRAL for more than two seconds, you must press the brake pedal to engage DRIVE or REVERSE.
Page 375: Towing A Disabled Vehicle
IN CASE OF EMERGENCY 373 TOWING A DISABLED VEHICLE WARNING! (Continued) The manufacturer requires towing your vehicle with all seconds continuously without stopping when you are four wheels off the ground using a flatbed. stuck and do not let anyone near a spinning wheel, no matter what the speed.
Page 376: Enhanced Accident Response System (Ears)
374 IN CASE OF EMERGENCY ENHANCED ACCIDENT RESPONSE SYSTEM (EARS) This vehicle is equipped with an Enhanced Accident Response System. Please refer to “Occupant Restraint Systems” in “Safety” for further information on the Enhanced Accident Re- sponse System (EARS) function. EVENT DATA RECORDER (EDR) This vehicle is equipped with an Event Data Recorder (EDR).
Page 377 SERVICING AND MAINTENANCE CONTENTS SCHEDULED SERVICING — SRT ... .377 ▫ Body Lubrication ..... .396 ▫...
Page 378 376 SERVICING AND MAINTENANCE ▫ Wheel And Wheel Trim Care ....431 BODYWORK ......435 ▫...
Page 379: Scheduled Servicing - Srt
SERVICING AND MAINTENANCE 377 • Change your engine oil more often if you drive your SCHEDULED SERVICING — SRT vehicle off-road for an extended period of time. The Scheduled Maintenance services listed in this manual • Under no circumstances should oil change intervals must be done at the times or mileages specified to protect exceed 6,000 miles (10,000 km) or six months, whichever your vehicle warranty and ensure the best vehicle perfor-...
Page 380: Maintenance Plan
378 SERVICING AND MAINTENANCE • Check all lights and other electrical items for correct CAUTION! operation. Failure to perform the required maintenance items At Each Oil Change may result in damage to the vehicle. • Change the engine oil filter. •...
Page 381 SERVICING AND MAINTENANCE 379 Miles: Or Months: 96 102 108 114 120 126 132 138 144 150 Or Kilometers: Adjust the parking brake on vehicles equipped with four wheel disc brakes. Drain the transfer case and refill. Inspect the accessory drive belts re- place if necessary.
Page 382 380 SERVICING AND MAINTENANCE Miles: Or Months: 96 102 108 114 120 126 132 138 144 150 Or Kilometers: Flush and replace the engine coolant at 120 months if not done at 150,000 miles (240,000 km). ** The spark plug change interval is mileage based only, WARNING! (Continued) monthly intervals do not apply.
Page 383: Engine Compartment
SERVICING AND MAINTENANCE 381 ENGINE COMPARTMENT 6.2L Supercharged Engine 1 — Remote Jump Start Positive Terminal 7 — Washer Fluid Reservoir 2 — Power Distribution Center (Fuses) 8 — Engine Oil Dipstick 3 — Intercooler Coolant Reservoir 9 — Coolant Pressure Cap (Radiator) 4 —...
Page 384: 6.4L Engine
382 SERVICING AND MAINTENANCE 6.4L Engine 1 — Remote Jump Start Positive Terminal 6 — Air Cleaner Filter 2 — Power Distribution Center (Fuses) 7 — Washer Fluid Reservoir 3 — Engine Oil Dipstick 8 — Coolant Pressure Cap (Radiator) 4 —...
Page 385: Checking Oil Level
SERVICING AND MAINTENANCE 383 The fluid reservoir for the windshield washers and the rear Checking Oil Level window washer is shared. The fluid reservoir is located in To assure proper lubrication of your vehicle’s engine, the the engine compartment, be sure to check the fluid level at engine oil must be maintained at the correct level.
Page 386: Dealer Service
384 SERVICING AND MAINTENANCE WARNING! CAUTION! (Continued) negative post. Battery posts are marked positive (+) • Battery fluid is a corrosive acid solution and can and negative (-) and are identified on the battery burn or even blind you. Do not allow battery fluid to case.
Page 387: Engine Oil
SERVICING AND MAINTENANCE 385 The manufacturer recommends the use of Pennzoil Ultra WARNING! 0W-40 engine or equivalent Mopar oil meeting the FCA Material Standard MS-12633 for use in all operating tem- You can be badly injured working on or around a peratures.
Page 388 386 SERVICING AND MAINTENANCE American Petroleum Institute (API) Engine Oil engine oil filler cap location, refer to “Engine Compart- Identification Symbol ment” in this section for further information. Synthetic Engine Oils This symbol means that the oil has You may use synthetic engine oils provided the recom- been certified by the American Pe- mended oil quality requirements are met, and the recom- troleum Institute (API).
Page 389: Engine Oil Filter
SERVICING AND MAINTENANCE 387 Engine Oil Filter WARNING! (Continued) The engine oil filter should be replaced with a new filter at near the engine compartment before starting the ve- every engine oil change. hicle with the air induction system (air cleaner, hoses, etc.) removed.
Page 390 388 SERVICING AND MAINTENANCE Engine Air Cleaner Filter Removal 2. Lift the air cleaner cover to access the air cleaner filter. 1. Release the spring clips from the air cleaner cover. Open Air Cleaner Filter Assembly 1 — Air Cleaner Cover Air Cleaner Filter Cover 2 —...
Page 391 SERVICING AND MAINTENANCE 389 3. Remove the air cleaner filter element from the housing Engine Air Cleaner Filter Installation assembly. NOTE: Inspect and clean the housing if dirt or debris is present before replacing the air filter element. 1. Install the air cleaner filter element into the housing assembly with the air cleaner filter inspection surface facing downward.
Page 392 390 SERVICING AND MAINTENANCE Engine Air Cleaner Filter Removal 2. Lift the air filter cleaner cover to access the air cleaner filter. 1. Loosen the fasteners on the air cleaner filter cover. Open Air Cleaner Filter Assembly Air Cleaner Filter Assembly 1 —...
Page 393: Accessory Drive Belt Inspection
SERVICING AND MAINTENANCE 391 3. Remove the air cleaner filter element from the housing 2. Install the air cleaner cover onto the housing assembly assembly. locating tabs. 3. Tighten the fasteners to lock the air cleaner cover to the housing assembly. Accessory Drive Belt Inspection WARNING! •...
Page 394: Air Conditioner Maintenance
392 SERVICING AND MAINTENANCE • “Groove jumping (belt does not maintain correct posi- However, cracks running along a rib (not across) are not normal. Any belt with cracks running along a rib must be tion on pulley) replaced. Also have the belt replaced if it has excessive •...
Page 395 SERVICING AND MAINTENANCE 393 Refrigerant Recovery And Recycling R134a — If WARNING! Equipped • Use only refrigerants and compressor lubricants ap- R-134a Air Conditioning Refrigerant is a hydrofluoro- proved by the manufacturer for your air conditioning carbon (HFC) that is an ozone-friendly substance. The system.
Page 396 394 SERVICING AND MAINTENANCE Air Conditioning Filter Replacement (A/C Air Filter) Refer to “Scheduled Servicing” in this section for the proper maintenance intervals. WARNING! Do not remove the cabin air filter while the vehicle is running, or while the ignition is in the ACC or ON/ RUN mode.
Page 397 SERVICING AND MAINTENANCE 395 NOTE: When disengaging the glove compartment door 5. Remove the filter cover by disengaging the retaining tab from its hinges, there will be some resistance. and mid way snap that secures the filter cover to the HVAC housing.
Page 398: Body Lubrication
396 SERVICING AND MAINTENANCE 7. Install the A/C air filter with the arrow on the filter lubricated periodically with a lithium based grease, such as pointing toward the floor. When installing the filter cover, Mopar Spray White Lube to assure quiet, easy operation make sure the retaining tabs fully engage the cover.
Page 399 SERVICING AND MAINTENANCE 397 Avoid using the wiper blades to remove frost or ice from Front Wiper Blade Removal/Installation the windshield. Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc. CAUTION! Do not allow the wiper arm to spring back against the NOTE: Life expectancy of wiper blades varies depending glass without the wiper blade in place or the glass may on geographical area and frequency of use.
Page 400 398 SERVICING AND MAINTENANCE 2. To disengage the wiper blade from the wiper arm, flip toward the right side of the vehicle to separate the wiper up the release tab on the wiper blade and while holding blade from the wiper arm). the wiper arm with one hand, slide the wiper blade down towards the base of the wiper arm.
Page 401 SERVICING AND MAINTENANCE 399 2. Position the wiper blade near the hook on the tip of the wiper arm with the wiper release tab open and the blade side of the wiper facing up and away from the wind- shield. 3.
Page 402 400 SERVICING AND MAINTENANCE NOTE: Resistance will be accompanied by an audible snap. 4. Still grasping the bottom end of the wiper blade, move the wiper blade upward and away from the wiper arm to disengage. Wiper Blade In Folded Out Position 1 —...
Page 403: Exhaust System
SERVICING AND MAINTENANCE 401 Installing The Rear Wiper have an authorized technician inspect the complete ex- haust system and adjacent body areas for broken, dam- 1. Lift the rear wiper arm pivot cap away from the glass to aged, deteriorated, or mispositioned parts. Open seams or allow the rear wiper blade to be raised off of the glass.
Page 404 402 SERVICING AND MAINTENANCE In unusual situations involving grossly malfunctioning CAUTION! engine operation, a scorching odor may suggest severe and abnormal catalyst overheating. If this occurs, stop the • The catalytic converter requires the use of unleaded vehicle, turn off the engine and allow it to cool. Service, fuel only.
Page 405: Cooling System
SERVICING AND MAINTENANCE 403 Cooling System WARNING! (Continued) • You or others can be badly burned by hot engine WARNING! coolant (antifreeze) or steam from your radiator. If • Turn vehicle off and disconnect the fan motor lead you see or hear steam coming from under the hood, before working near the radiator cooling fan.
Page 406 404 SERVICING AND MAINTENANCE Cooling System — Drain, Flush And Refill CAUTION! (Continued) NOTE: Some vehicles require special tools to add coolant Additive Technology (OAT) engine coolant is differ- properly. Failure to fill these systems properly could lead to ent and should not be mixed with Hybrid Organic severe internal engine damage.
Page 407 SERVICING AND MAINTENANCE 405 Adding Coolant • Use only high purity water such as distilled or deionized water when mixing the water/engine coolant (anti- Your vehicle has been built with an improved engine freeze) solution. The use of lower quality water will coolant (OAT coolant conforming to MS.90032) that allows reduce the amount of corrosion protection in the engine extended maintenance intervals.
Page 408 406 SERVICING AND MAINTENANCE Cooling System Pressure Cap Disposal Of Used Coolant The cap must be fully tightened to prevent loss of engine Used ethylene glycol-based coolant (antifreeze) is a regu- coolant (antifreeze), and to ensure that engine coolant lated substance requiring proper disposal. Check with your (antifreeze) will return to the radiator from the coolant local authorities to determine the disposal rules for your expansion bottle/recovery tank if so equipped.
Page 409: Brake System
SERVICING AND MAINTENANCE 407 Points To Remember • Make sure that the coolant expansion bottle overflow hoses are not kinked or obstructed. NOTE: When the vehicle is stopped after a few miles/ • Keep the front of the radiator clean. If your vehicle is kilometers of operation, you may observe vapor coming equipped with air conditioning, keep the front of the from the front of the engine compartment.
Page 410 408 SERVICING AND MAINTENANCE Fluid Level Check — Brake Master Cylinder WARNING! (Continued) The fluid level of the master cylinder should be checked identified on the original factory installed hydraulic whenever the vehicle is serviced, or immediately if the master cylinder reservoir. brake system warning light is on.
Page 411: Automatic Transmission
SERVICING AND MAINTENANCE 409 Special Additives Automatic Transmission The manufacturer strongly recommends against using any Selection Of Lubricant special additives in the transmission. Automatic Transmis- It is important to use the proper transmission fluid to sion Fluid (ATF) is an engineered product and its perfor- ensure optimum transmission performance and life.
Page 412: Front/Rear Axle Fluid
410 SERVICING AND MAINTENANCE fluid level checked. Operating the vehicle with an im- If gear oil leakage is suspected inspect the fluid level. Refer proper fluid level can cause severe transmission damage. to “Fluids And Lubricants” in “Technical Specifications” for further information. CAUTION! Front Axle Fluid Level Check If a transmission fluid leak occurs, visit an authorized...
Page 413: Transfer Case
SERVICING AND MAINTENANCE 411 Drain CAUTION! First remove fill plug, then remove drain plug. Recom- Do not overtighten the plugs as it could damage them mended tightening torque for drain and fill plugs is 15 to and cause them to leak. 25 ft lbs (20 to 34 N·m).
Page 414 412 SERVICING AND MAINTENANCE Tire Markings NOTE: • P (Passenger) — Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Example: P215/65R15 95H. • European — Metric tire sizing is based on European design standards.
Page 415 SERVICING AND MAINTENANCE 413 Tire Sizing Chart EXAMPLE: Example Size Designation: P215/65R15XL 95H, 215/65R15 96H, LT235/85R16C, T145/80D18 103M, 31x10.5 R15 LT P = Passenger car tire size based on U.S. design standards, or ..blank..= Passenger car tire based on European design standards, or LT = Light truck tire based on U.S.
Page 416 414 SERVICING AND MAINTENANCE EXAMPLE: H = Speed Symbol – A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under cer- tain operating conditions – The maximum speed corresponding to the speed symbol should only be achieved under specified operating condi- tions (i.e., tire pressure, vehicle loading, road conditions, and posted speed limits) Load Identification: Absence of the following load identification symbols on the sidewall of the tire indicates a Standard Load (SL) tire:...
Page 417 SERVICING AND MAINTENANCE 415 Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire; the TIN on the outboard side of black sidewall tires as however, the date code may only be on one side. Tires with mounted on the vehicle.
Page 418 416 SERVICING AND MAINTENANCE Tire Terminology And Definitions Term Definition B-Pillar The vehicle B-Pillar is the structural member of the body located be- hind the front door. Cold Tire Inflation Pressure Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after sitting for a minimum of three hours.
Page 419 SERVICING AND MAINTENANCE 417 Tire Loading And Tire Pressure NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door. Check the inflation pressure of each tire, including the spare tire (if equipped), at least monthly and inflate to the recommended pressure for your vehicle.
Page 420 418 SERVICING AND MAINTENANCE Tire And Loading Information Placard Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the Tire and Loading Information placard in “Vehicle Loading”...
Page 421 SERVICING AND MAINTENANCE 419 Steps For Determining Correct Load Limit— this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. (1) Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or Metric Example For Load Limit XXX lbs.”...
Page 422 420 SERVICING AND MAINTENANCE WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the rec- ommended load capacity for your vehicle. Never over- load them.
Page 423: Tires - General Information
SERVICING AND MAINTENANCE 421 Tires — General Information WARNING! (Continued) Tire Pressure • Overinflated or underinflated tires can affect vehicle handling and can fail suddenly, resulting in loss of Proper tire inflation pressure is essential to the safe and vehicle control. satisfactory operation of your vehicle.
Page 424 422 SERVICING AND MAINTENANCE Tread Wear CAUTION! Improper cold tire inflation pressures can cause abnormal After inspecting or adjusting the tire pressure, always wear patterns and reduced tread life, resulting in the need reinstall the valve stem cap. This will prevent moisture for earlier tire replacement.
Page 425 SERVICING AND MAINTENANCE 423 pressure should be increased by 3 psi (21 kPa), which Radial Ply Tires equals 1 psi (7 kPa) for every 12°F (7°C) for this outside temperature condition. WARNING! Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) Combining radial ply tires with other types of tires on during operation.
Page 426 424 SERVICING AND MAINTENANCE Run Flat Tires — If Equipped Tire Spinning Run Flat tires allow you the capability to drive 50 miles When stuck in mud, sand, snow, or ice conditions, do not (80 km) at 50 mph (80 km/h) after a rapid loss of inflation spin your vehicle’s wheels above 30 mph (48 km/h) or for pressure.
Page 427 SERVICING AND MAINTENANCE 425 Tread Wear Indicators worn to the tread wear indicators, the tire should be replaced. Refer to “Replacement Tires” in this section for Tread wear indicators are in the original equipment tires to further information. help you in determining when your tires should be re- placed.
Page 428 426 SERVICING AND MAINTENANCE It is recommended to replace the two front tires or two rear WARNING! (Continued) tires as a pair. Replacing just one tire can seriously affect You could lose control and have a collision resulting in your vehicle’s handling. If you ever replace a wheel, make serious injury or death.
Page 429: Tire Types
SERVICING AND MAINTENANCE 427 tire sidewall. Use all season tires only in sets of four; failure WARNING! (Continued) to do so may adversely affect the safety and handling of • Never use a tire with a smaller load index or capacity, your vehicle.
Page 430: Spare Tires - If Equipped
428 SERVICING AND MAINTENANCE Snow Tires Spare Tires — If Equipped Some areas of the country require the use of snow tires NOTE: For vehicles equipped with Tire Service Kit instead during the Winter. Snow tires can be identified by a of a spare tire, please refer to “Tire Service Kit”...
Page 431 SERVICING AND MAINTENANCE 429 spare by looking at the spare tire description on the Tire WARNING! (Continued) and Loading Information Placard located on the driver’s needs to be replaced. Be sure to follow the warnings, side door opening or on the sidewall of the tire. Compact which apply to your spare.
Page 432 430 SERVICING AND MAINTENANCE Limited Use Spare — If Equipped WARNING! The limited use spare tire is for temporary emergency use Compact and Collapsible spares are for temporary only. This tire is identified by a label located on the limited emergency use only.
Page 433: Wheel And Wheel Trim Care
SERVICING AND MAINTENANCE 431 When cleaning extremely dirty wheels including excessive Wheel And Wheel Trim Care brake dust, care must be taken in the selection of tire and All wheels and wheel trim, especially aluminum and wheel cleaning chemicals and equipment to prevent dam- chrome plated wheels, should be cleaned regularly using age to the wheels.
Page 434: Tire Chains (Traction Devices)
432 SERVICING AND MAINTENANCE Dark Vapor Chrome, Black Satin Chrome, or Low Gloss WARNING! Clear Coat Wheels Using tires of different size and type (M+S, Snow) CAUTION! between front and rear axles can cause unpredictable handling. You could lose control and have a collision. If your vehicle is equipped with these specialty wheels, DO NOT USE wheel cleaners, abrasives, or CAUTION!
Page 435: Tire Rotation Recommendations
SERVICING AND MAINTENANCE 433 NOTE: The premium Tire Pressure Monitor System will CAUTION! (Continued) automatically locate the pressure values displayed in the • Observe the traction device manufacturer’s instruc- correct vehicle position following a tire rotation. tions on the method of installation, operating speed, The suggested rotation method is the “rearward-cross”...
Page 436: Department Of Transportation Uniform Tire Quality Grades
434 SERVICING AND MAINTENANCE on wet pavement, as measured under controlled condi- DEPARTMENT OF TRANSPORTATION UNIFORM tions on specified government test surfaces of asphalt TIRE QUALITY GRADES and concrete. A tire marked C may have poor traction The following tire grading categories were established performance.
Page 437: Storing The Vehicle
SERVICING AND MAINTENANCE 435 represent higher levels of performance on the laboratory BODYWORK test wheel, than the minimum required by law. Protection From Atmospheric Agents Vehicle body care requirements vary according to geo- WARNING! graphic locations and usage. Chemicals that make roads The temperature grade for this tire is established for passable in snow and ice and those that are sprayed on a tire that is properly inflated and not overloaded.
Page 438: Body And Underbody Maintenance
436 SERVICING AND MAINTENANCE • Salt in the air near seacoast localities. • If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar Super Kleen Bug and Tar • Atmospheric fallout/industrial pollutants. Remover to remove. Body And Underbody Maintenance •...
Page 439: Interiors
SERVICING AND MAINTENANCE 437 • If you detect any stone chips or scratches in the paint, WARNING! touch them up immediately. The cost of such repairs is considered the responsibility of the owner. Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed •...
Page 440: Plastic And Coated Parts
438 SERVICING AND MAINTENANCE 2. Dry with a soft cloth. WARNING! (Continued) Leather Parts must be replaced after a collision if they have been damaged (i.e., bent retractor, torn webbing, etc.). Mopar Total Clean is specifically recommended for leather upholstery. Plastic And Coated Parts Your leather upholstery can be best preserved by regular Use Mopar Total Clean to clean vinyl upholstery.
Page 441: Glass Surfaces
SERVICING AND MAINTENANCE 439 CAUTION! Do not use Alcohol and Alcohol-based and/or Ketone based cleaning products to clean leather seats, as damage to the seat may result. Glass Surfaces All glass surfaces should be cleaned on a regular basis with Mopar Glass Cleaner, or any commercial household-type glass cleaner.
Page 443 TECHNICAL SPECIFICATIONS CONTENTS IDENTIFICATION DATA....442 ▫ Do Not Use E-85 In Non-Flex Fuel Vehicles ..446 ▫ Vehicle Identification Number ... . .442 ▫...
Page 444: Identification Data
442 TECHNICAL SPECIFICATIONS IDENTIFICATION DATA Vehicle Identification Number The Vehicle Identification Number (VIN) is found on a label located on the left front corner of the instrument panel pad, visible from outside of the vehicle through the wind- shield. This number also is stamped on the right front floor, behind the right front seat.
Page 445: Wheel And Tire Torque Specifications
TECHNICAL SPECIFICATIONS 443 In the event power assist is lost for any reason (i.e., Inspect the wheel mounting surface prior to mounting the repeated brake applications with the engine off) the brakes tire and remove any corrosion or loose particles. will still function.
Page 446: Fuel Requirements
444 TECHNICAL SPECIFICATIONS FUEL REQUIREMENTS 6.2L Supercharged And 6.4L Engine Do not use E-85 flex fuel or ethanol blends greater than 15% in this engine. These engines are designed to meet all emissions regulations, provide optimal fuel economy and performance when using high-quality unleaded...
Page 447: Reformulated Gasoline
TECHNICAL SPECIFICATIONS 445 Designated TOP TIER Detergent Gaso- Poor quality gasoline can cause problems such as hard line contains a higher level of detergents starting, stalling, and hesitations. If you experience these to further aide in minimizing engine symptoms, try another brand of gasoline before consider- and fuel system deposits.
Page 448: Do Not Use E-85 In Non-Flex Fuel Vehicles
446 TECHNICAL SPECIFICATIONS • Poor cold start and cold drivability. CAUTION! (Continued) • Increased risk for fuel system component corrosion. cause emissions to exceed the applicable standard, and/or cause the “Malfunction Indicator Light” to CNG And LP Fuel System Modifications illuminate.
Page 449: Fuel System Cautions
TECHNICAL SPECIFICATIONS 447 NOTE: Intentional tampering with the emissions control Fuel System Cautions system can result in civil penalties being assessed against CAUTION! you. Follow these guidelines to maintain your vehicle’s Carbon Monoxide Warnings performance: WARNING! • The use of leaded gasoline is prohibited by Federal law.
Page 450: Fluid Capacities
448 TECHNICAL SPECIFICATIONS FLUID CAPACITIES U.S. Metric Fuel (Approximate) 24.6 Gallons 93.1 Liters Engine Oil With Filter 6.2 Liter Engine (SAE 0W-40, Synthetic API Certified, MS-12633) 8.3 Quarts 7.8 Liters 6.4 Liter Engine (SAE 0W-40, Synthetic API Certified, MS-12633) 7 Quarts 6.6 Liters Cooling System* 6.2L Engine (Mopar Antifreeze/Engine Coolant 10 Year/150,000 Mile...
Page 451: Fluids And Lubricants
TECHNICAL SPECIFICATIONS 449 FLUIDS AND LUBRICANTS Engine Component Fluid, Lubricant or Genuine Part Engine/Intercooler Coolant We recommend you use Mopar Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Tech- nology) that meets the requirements of FCA Material Standard MS.90032. Engine Oil For best performance and maximum protection under all types of operating conditions, the manufacturer only rec- ommends full synthetic engine oils that meet the American...
Page 452: Chassis
450 TECHNICAL SPECIFICATIONS Chassis Component Fluid, Lubricant, or Genuine Part Automatic Transmission Use only Mopar ZF 8&9 Speed ATF Automatic Transmis- sion Fluid or equivalent. Failure to use the correct fluid may affect the function or performance of your transmis- sion.
Page 453 MULTIMEDIA CONTENTS UCONNECT RADIOS ....454 ▫ Track Mode ......487 PERSONALIZED MENU BAR .
Page 454 452 MULTIMEDIA ▫ CD Player ......498 ▫ Unwired Stereo Headphone Lifetime Limited Warranty ......510 IPOD/USB/MP3 CONTROL —...
Page 455 MULTIMEDIA ▫ SiriusXM Travel Link (4C/4C NAV) ..525 ▫ General Information .....529 ▫...
Page 456: Uconnect Radios
454 MULTIMEDIA UCONNECT RADIOS For detailed information about your Uconnect radio, refer to your Uconnect Owner’s Manual Supplement. NOTE: Uconnect screen images are for illustration pur- poses only and may not reflect exact software for your vehicle. PERSONALIZED MENU BAR The Uconnect features and services in the main menu bar are easily changed for your convenience.
Page 457: Cybersecurity
MULTIMEDIA CYBERSECURITY WARNING! Your vehicle may be a connected vehicle and may be • It is not possible to know or to predict all of the equipped with both wired and wireless networks. These possible outcomes if your vehicle’s systems are networks allow your vehicle to send and receive informa- breached.
Page 458: Uconnect Settings
456 MULTIMEDIA NOTE: UCONNECT SETTINGS • FCA US LLC or your dealer may contact you directly The Uconnect system uses a combination of buttons on the regarding software updates. touchscreen and buttons on the faceplate located on the center of the instrument panel that allow you to access and •...
Page 459: Customer Programmable Features - Uconnect 4C/4C Nav Settings
MULTIMEDIA NOTE: Depending on the vehicles options, feature settings Customer Programmable Features — Uconnect may vary. 4C/4C NAV Settings Press the “Apps ” button, then press the “Settings” When making a selection, press the button on the touch- button on the touchscreen to display the menu setting screen to enter the desired mode.
Page 460 458 MULTIMEDIA Setting Name Selectable Options Display Brightness With Headlights OFF NOTE: To make changes to the Display Brightness with Headlights OFF setting, the headlights must be off and the interior dimmer switch must not be in the party or parade positions. Set Theme NOTE: When the “Set Theme”...
Page 461 MULTIMEDIA Setting Name Selectable Options Keyboard Smart Keyboard Selection Latin Keyboard NOTE: Latin Keyboard displays different keyboard layouts to choose from. The selectable keyboards are ABCDEF Keyboard, QWERTY Keyboard, and AZERTY Keyboard. Touchscreen Beep Control Screen Time-Out — If Equipped NOTE: When the “Control Screen Time-Out”...
Page 462 460 MULTIMEDIA Units After pressing the “Units” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Units Metric Custom NOTE: The “Custom” option allows you to set the “Speed” (MPH, or km/h), “Distance” (mi, or km), “Fuel Consumption” [MPG (US), MPG (UK), L/100 km, or km/L], “Pressure”...
Page 463 MULTIMEDIA Clock After pressing the “Clock” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Sync Time With GPS Set Time Hours NOTE: The “Set Time Hours” feature will allow you to adjust the hours. The “Sync time with GPS” button on the touch- screen must be unchecked.
Page 464 462 MULTIMEDIA Camera After pressing the “Camera” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Surround View Camera Delay NOTE: The “Surround View Camera Delay” setting determines whether or not the screen will display the 360 degree view image with guidelines for up to ten seconds after the vehicle is shifted out of REVERSE.
Page 465 MULTIMEDIA Setting Name Selectable Options ParkView Backup Camera Active Guide Lines — If Equipped NOTE: The “ParkView Backup Camera Active Guide Lines” feature overlays the Rear Backup Camera image with active, or dynamic, grid lines to help illustrate the width of the vehicle and its project back up path, based on the steering wheel position when the option is checked.
Page 466 464 MULTIMEDIA Setting Name Selectable Options Forward Collision Warning includes Advanced Brake Assist (ABA). The ABA applies additional brake pressure when the driver requests insufficient brake pressure to avoid a potential frontal collision. When the “Sound Only” option is selected a chime will sound alerting you of a possible collision with the vehicle in front of you and more brake pres- sure is needed.
Page 467 MULTIMEDIA Setting Name Selectable Options Rear ParkSense Chime Medium High Volume Front ParkSense Chime Medium High Volume Rear ParkSense Braking Assist — If Equipped NOTE: When the “Rear ParkSense Braking Assist” feature is selected, the park assist system will detect objects located be- hind the vehicle and utilize autonomous braking to stop the vehicle.
Page 468 466 MULTIMEDIA Setting Name Selectable Options any damage in the area where the sensor is located, even if the fascia is not damaged, the sensor may have become misaligned. Take your vehicle to an authorized dealer to verify sensor alignment. A sensor that is misaligned will re- sult in the Blind Spot Alert System not operating to specification.
Page 469 MULTIMEDIA Brakes Setting — If Equipped After pressing the “Brakes” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Brake Service NOTE: Selecting the “Brake Service” feature will display a pop-up asking whether or you would like to retract the park brakes to all break system service.
Page 470 468 MULTIMEDIA Setting Name Selectable Options Auto Dim High Beams — If Equipped NOTE: When the “Auto Dim High Beams” feature is selected, the high beam headlights will activate/deactivate automati- cally under certain conditions. Daytime Running Lights — If Equipped Flash Lights With Lock Doors &...
Page 471 MULTIMEDIA Setting Name Selectable Options Auto Unlock On Exit NOTE: When this feature is selected, all doors will unlock when the vehicle is stopped, the transmission is in the PARK or NEUTRAL position and the driver’s door is opened. Flash Lights With Lock Sound Horn With Lock 1st Press 2nd Press...
Page 472 470 MULTIMEDIA Setting Name Selectable Options Passive Entry — If Equipped NOTE: This feature allows you to lock and unlock the vehicles door(s) without having to push the key fob lock or unlock buttons. Personal Settings Linked to Key Fob — If Equipped NOTE: This feature provides automatic recall of all settings stored to a memory location (driver’s seat, exterior mirrors, steer-...
Page 473 MULTIMEDIA Engine Off Options After pressing the “Engine Off Options” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Engine Off Power 0 sec 45 sec 5 min 10 min Delay — If Equipped NOTE: When the “Engine Off Power Delay”...
Page 474 472 MULTIMEDIA Audio After pressing the “Audio” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Balance/Fade Speaker Icon NOTE: When in this display you may adjust the “Balance/Fade” of the audio by pressing and dragging the “Speaker Icon” toward any location in the box.
Page 475 MULTIMEDIA Phone/Bluetooth After pressing the “Phone/Bluetooth” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Phone Pop-Ups Displayed in Cluster Do Not Disturb Do Not Disturb Options NOTE: The “Do Not Disturb” feature allows the paired phone to send a predetermined call, text, or both, to any incoming call, or text, before sending it directly to voicemail.
Page 476 474 MULTIMEDIA SiriusXM Setup — If Equipped After pressing the “SiriusXM Setup” button on the touch- screen, the following settings will be available: Setting Name Selectable Options SXM Tune Start NOTE: The “Tune Start” feature begins playing the current song from the beginning when you tune to a music channel using one of the twelve presets, so you can enjoy the complete song.
Page 477 MULTIMEDIA Setting Name Selectable Options 2. Write down the Sirius ID numbers for your receiver. To reactivate your service, either call the number listed on the screen or visit the provider online. SiriusXM Travel Link is a separate subscription. Accessibility — If Equipped After pressing the “Accessibility”...
Page 478 476 MULTIMEDIA Reset Settings After pressing the “Restore Settings” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Reset App Drawer Cancel Restore Settings Cancel NOTE: When this feature is selected it will reset all settings to their default settings. Clear Personal Data Cancel NOTE:...
Page 479: Srt Performance Pages - If Equipped
MULTIMEDIA The Performance Pages include the following: SRT PERFORMANCE PAGES — IF EQUIPPED • Home Performance Pages is an application that provides a dis- play for performance indicators, as received from the • Timers instrument cluster, that will help you gain familiarity with •...
Page 480: Home
478 MULTIMEDIA The following describes each feature and its operation: 2. Select the following option from the menu: • Set Widget: Top Left Home • Set Widget: Top Right • Set Widget: Bottom Left • Set Widget: Bottom Right 3. After selecting a Widget location: select the gauge or timer to display: •...
Page 481: Timers
MULTIMEDIA • Timer: Brake Distance When the Timers Page is selected, you will be able to select from following “Tickets”: • Timer: Reaction Time • Recent NOTE: Pressing the “Camera” icon in the upper right corner of the Performance Pages screen will take a screenshot of the Pressing the “Recent”...
Page 482 480 MULTIMEDIA The “Tickets” contain the timers listed below: • Reaction Time Measures the driver’s reaction time for launching the vehicle against a simulated drag strip timing light (behav- ior modeled after 500 Sportsman Tree) displayed in the instrument cluster display. NOTE: The Reaction Time, MPH, ⅛...
Page 483: Gauges
MULTIMEDIA • ⅛ Mile (200 meter) MPH Gauges Displays the vehicle speed at the time ⅛ mile was reached. • ¼ Mile (400 meter) ET Displays the time it takes for the vehicle to go ¼ mile (400 meters). • ¼ Mile (400 meter) MPH Displays the speed the vehicle was at when ¼...
Page 484 482 MULTIMEDIA • Coolant Temperature Pressing the left or right arrows will cycle through the details for each gauge. Pressing the lower X button in the Shows the actual coolant temperature. top right corner will return to the gauge main menu. •...
Page 485: G-Force
MULTIMEDIA When G-Force is selected, the following features will be G-Force available: • Vehicle Speed: Measures the current speed of the vehicle in either mph or km/h, starting at zero with no maximum value. • Front G-Force: Measures the braking force. •...
Page 486: Engine
484 MULTIMEDIA • Steering Wheel Angle Engine Steering Wheel Angle utilizes the steering angle sensor to measure the degree of the steering wheel relative to zero. The zero degree measurement indicates a steering wheel straight ahead position. When the steering angle value is negative, a turn to the left is indicated, and when the steering angle value is positive, a turn to the right is indicated.
Page 487: Dynamometer (Dyno)
MULTIMEDIA • Instantaneous Torque Dynamometer (Dyno) Shows the instantaneous torque. • Oil Pressure (6.4L Only) Shows the actual engine oil pressure. • Gear (Automatic Transmission Only) Shows the current (or pending) operating gear of the vehicle. • Boost Pressure (6.2L Only) Shows the actual boost pressure.
Page 488: Srt Drive Modes
486 MULTIMEDIA The following options can be selected: SRT DRIVE MODES • Pressing the STOP button will freeze the graph. Selecting Play will clear the graph and restart the process over • Press the “+” or “–” buttons to change the history of the graph.
Page 489: Track Mode
MULTIMEDIA • Pressing the SRT button on the console switch. Listed below are the available Drive Modes: • Pressing the Custom button on the Selec-Track switch. Track Mode • Selecting “Drive Modes” from the “Apps” menu. • Selecting “Drive Modes” from within the Performance Pages menu.
Page 490: Sport Mode
488 MULTIMEDIA NOTE: Electronic Stability Control (ESC) Full-Off can be Suspension systems are all set to their “Sport” settings activated by pushing and holding the ESC Off button on highlighted in orange. The Paddle Shifters are enabled. the instrument panel switch bank for five seconds. Tow Mode Sport Mode Drive Modes (Tow)
Page 491: Snow Mode
MULTIMEDIA Stability Control is set to “Full” highlighted in blue. Selecting “Snow” with the Selec-Track switch will activate All-Wheel Drive is set to “50/50” highlighted in blue. snow mode for use on loose traction surfaces. When in Steering is set to “Street” highlighted in yellow. Suspension Snow mode (depending on certain operating conditions), is set to “Sport”...
Page 492: Auto Mode
490 MULTIMEDIA their “Street” settings highlighted in yellow. Steering and Auto Mode Suspension can be configured in either the “Street,” “Sport,” or “Track” and the Paddle Shifters may be enabled or disabled while in auto set-up mode. Drive Mode Auto (Default) Auto mode is enabled upon ignition on, or by selecting “Auto”...
Page 493: Custom Mode
MULTIMEDIA the All-Wheel Drive, Stability Control, Transmission, Steer- Custom Mode ing, Suspension, and Paddle Shifter settings are shown in their current configuration. While in the Custom Mode screen, press the “Custom Set-Up” button on the touchscreen to access the selectable options.
Page 494: Race Options
492 MULTIMEDIA RACE OPTIONS Launch Control WARNING! Launch Mode is intended for off-highway or off-road use only and should not be used on any public roadways. It is recommended that this feature be used in a controlled environment, and within the limits of the law.
Page 495 MULTIMEDIA Launch Control button on the Selec-Track Switch, or by pressing the “Cancel Launch Mode” button on the touch- screen. NOTE: Launch RPM Set-Up cannot be accessed unless Launch Mode is deactivated. Activate Launch Control Launch Control can be accessed by pushing the Launch button on the Selec-Track switch or pushing the SRT button on the Selec-Track switch then selecting the “Race Options”...
Page 496: Shift Light
494 MULTIMEDIA To adjust the Launch RPM, drag the slider bar or press the arrows on the touchscreen to adjust the holding RPM. The launch RPM limit will display in the head units tachometer display. Shift Light Your vehicle is equipped with a shift light feature that illuminates the back lighting of the tachometer (in red) within the instrument cluster display.
Page 497: Valet Mode
MULTIMEDIA Factory Default” button on the touchscreen to change back asked to enter a four digit PIN code. The PIN code is not to factory settings, or press the “Shift Light Off” button on set, so you are free to select any four digit numeric the touchscreen to turn the system off completely.
Page 498 496 MULTIMEDIA Valet Mode Deactivation Valet Mode Deactivation PIN To exit Valet Mode you must enter the same four digit PIN The Valet Mode Deactivation key pad will then prompt that was used to enter the mode. The unlock keypad can be you for your four digit PIN code, enter your PIN code and accessed by either pushing the SRT button on Selec-Track press the “OK”...
Page 499: Eco Mode
MULTIMEDIA the increased amount of operating conditions where the ECO MODE vehicle is allowed to operate in four cylinder shutoff mode. The Paddle Shifters will be disabled while in ECO mode. • ECO will be disabled when another Drive Mode is selected or ECO button is pushed.
Page 500: Radio Operation
498 MULTIMEDIA The right-hand control is a rocker-type switch with a CD Player push-button in the center and controls the volume and Pushing the top of the switch once will go to the next track mode of the sound system. Pushing the top of the rocker on the CD.
Page 501: Uconnect Rear Seat Entertainment (Rse) System - If Equipped
MULTIMEDIA UCONNECT REAR SEAT ENTERTAINMENT (RSE) SYSTEM — IF EQUIPPED Your Rear Seat Entertainment System is designed to give your family years of enjoyment. You can play your favorite CDs, DVDs or Blu-ray Discs, listen to audio over the wireless headphones, or plug and play a variety of stan- dard video games or audio devices.
Page 502 500 MULTIMEDIA • Turn on the Rear Seat Entertainment system by pushing • With the Dual Video Screen System, Channel 1 (Rear 1) the power button on the remote control. on the remote control and headphones, refers to Screen 1 (driver’s side) and Channel 2 (Rear 2) on the Remote •...
Page 503: Dual Video Screen
MULTIMEDIA Blu-ray Disc Player Play A Blu-ray Disc The Blu-ray disc player is located in the center console. RSE System Headphone Channel Selectors • The system can be controlled either by the front seat occupants utilizing the touchscreen radio or by the rear seat occupants using the remote control.
Page 504 502 MULTIMEDIA 3. To watch a Blu-ray disc on Rear 2 for passenger side rear Using The Touchscreen Radio passengers, ensure the Remote Control and Headphone switch is on Rear 2. NOTE: • To view a Blu-ray disc on the radio, press the “Media” button on the touchscreen, and then press the “Disc”...
Page 505 MULTIMEDIA 3. RSE Mute 8. RSE Mode Mute rear headphones for the current ignition cycle. Press- Select this button to change source for the active (high- ing mute again will unmute rear headphones. lighted) rear Screen/Channel on the rear media control screen.
Page 506: Play Video Games
504 MULTIMEDIA 1. HDMI Input. Play Video Games Connect the video game console to the Audio/Video 2. Right audio in (red). RCA/HDMI input jacks located on the side of each seat. 3. Left audio in (white). Audio/Video RCA/HDMI Jacks (AUX/HDMI Jacks) on 4.
Page 507 MULTIMEDIA Using The Remote Control Using The Touchscreen Radio Controls 1. Push the SOURCE button on the Remote Control. 1. Press the Media button on the Uconnect radio touch- screen. 2. While looking at Rear 1 or 2, highlight DISC by either pushing Up/Down/Left/Right buttons, then push 2.
Page 508: Important Notes For Dual Video Screen System
506 MULTIMEDIA 3. Press the 1 or 2 buttons on the touchscreen, and the Important Notes For Dual Video Screen System select source button on the touchscreen. Press the DISC • The Rear Seat Entertainment System is able to transmit button on the touchscreen in the MEDIA column.
Page 509: Blu-Ray Disc Player Remote Control - If Equipped
MULTIMEDIA 3. SOURCE — Push to enter Source Selection screen. Blu-ray Disc Player Remote Control — If Equipped 4. Channel/Screen Selector Switch — Indicates which channel is being controlled by the remote control. When the selector switch is in the Rear 1 position, the remote controls the functionality of headphone Channel 1 (left screen).
Page 510: Headphones Operation
508 MULTIMEDIA — Push and hold to fast rewind through the current audio track or video chapter. — Mutes headphone audio. 15. BACK — Push to exit out of menus or return to source selection screen. — Push to navigate menus. 17.
Page 511: Replacing The Headphone Batteries
MULTIMEDIA NOTE: The rear video system must be turned on before 4. When the Mode Selection menu appears on screen, use sound can be heard from the headphones. To conserve the cursor buttons on the remote control to navigate to battery life, the headphones will automatically turn off the available modes and push the OK button to select approximately three minutes after the rear video system is...
Page 512: Unwired Stereo Headphone Lifetime Limited Warranty
510 MULTIMEDIA states and jurisdictions may not allow the exclusion or Unwired Stereo Headphone Lifetime Limited limitation of incidental or consequential damages, so the Warranty above limitation may not apply to you. This warranty gives Who Does This Warranty Cover? This warranty covers the you specific legal rights.
Page 513 MULTIMEDIA System Information video on the screen. The factory default settings are already set for optimum viewing, so there is no need to change Disc Menu these settings under normal circumstances. When listening to a CD Audio or CD Data disc, pushing To change the settings, push the remote control’s naviga- the remote control’s POP UP/MENU button displays a list tion buttons ( ,...
Page 514 512 MULTIMEDIA • When the screen is reopened, the video screen will DVD Region Codes automatically turn back on and show the appropriate The Blu-ray Disc player and many DVD discs are coded by display menu or media. geographic region. These region codes must match in order If the screen is closed and there is no audio heard, verify for the disc to play.
Page 515 MULTIMEDIA If you record a disc using a personal computer, there may The recommended method for labeling recordable discs be cases where the Blu-ray Disc player may not be able to (CD-R, CD-RW, and DVD-R) is with a permanent marker. play some or the entire disc, even if it is recorded in a Do not use adhesive labels as they may separate from the compatible format and is playable on other players.
Page 516 514 MULTIMEDIA • Other compression formats such as AAC, MP3 Pro, Ogg the disc is reached, the Blu-ray Disc player will return to Vorbis, and ATRAC3 will not play. The Blu-ray player the beginning of the disc and attempt to play the start of will automatically skip the file and begin playing the the first track.
Page 517: Radio Operation And Mobile Phones
MULTIMEDIA The radio manufacturer believes the internal wireless radio RADIO OPERATION AND MOBILE PHONES is safe for use by consumers. The level of energy emitted is Under certain conditions, the mobile phone being on in far less than the electromagnetic energy emitted by wire- your vehicle can cause erratic or noisy performance from less devices such as mobile phones.
Page 518: Uconnect Voice Recognition Quick
516 MULTIMEDIA NOTE: UCONNECT VOICE RECOGNITION QUICK TIPS • This equipment has been tested and found to comply Introducing Uconnect with the limits for a Class B digital device, pursuant to Start using Uconnect Voice Recognition with these helpful Part 15 of the FCC Rules. These limits are designed to quick tips.
Page 519: Get Started
MULTIMEDIA If you see the NAV icon on your touchscreen, you have the Uconnect 4C NAV system. If not, you have a Uconnect 4C system. Get Started All you need to control your Uconnect system with your voice are the buttons on your steering wheel. Helpful hints for using Voice Recognition: 1.
Page 520: Radio
518 MULTIMEDIA Push the VR button . After the beep, say: TIP: At any time, if you are not sure of what to say or want to learn a Voice Command, push the VR button and say • “Cancel” to stop a current voice session “Help.”...
Page 521: Media
MULTIMEDIA TIP: Press the Browse button on the touchscreen to see all Media of the music on your AUX or USB device. Your Voice Uconnect offers connections via USB, Bluetooth and auxil- Command must match exactly how the artist, album, song iary ports (if equipped).
Page 522: Phone
520 MULTIMEDIA Phone Making and answering hands-free phone calls is easy with Uconnect. When the Phonebook button is illuminated on your touchscreen, your system ready. Check UconnectPhone.com for mobile phone compatibility and pairing instructions. Push the Phone button . After the beep, say one of the following commands: •...
Page 523: Climate (4C/4C Nav)
MULTIMEDIA Climate (4C/4C NAV) Too hot? Too cold? Adjust vehicle temperatures hands-free and keep everyone comfortable while you keep moving ahead. (If vehicle is equipped with climate control.) Push the VR button . After the beep, say one of the following commands: •...
Page 524: Navigation (4C/4C Nav)
522 MULTIMEDIA Navigation (4C/4C NAV) The Uconnect navigation feature helps you save time and become more productive when you do not know exactly how to get to where you want to go. (Navigation is optional on the Uconnect 4C NAV system. See an autho- rized dealer to activate navigation at any time.) 1.
Page 525: Siriusxm Guardian (4C Nav) - If Equipped
MULTIMEDIA Send & Go SiriusXM Guardian (4C NAV) — If Equipped Vehicle Finder CAUTION! Stolen Vehicle Assistance Some SiriusXM Guardian services, including SOS Call Remote Vehicle Start** and Roadside Assistance Call will NOT work without an operable LTE (voice/data) or 3G or 4G (data) net- Remote Horn &...
Page 526: Vehicle Health Report/Alert (4C Nav)
524 MULTIMEDIA 3. Select “Customer Care” to speak with a SiriusXM Mobile App (4C NAV) Guardian Customer Care agent who will activate ser- You’re only a few steps away from using remote com- vices in your vehicle, or select “Enter Email” to activate mands.
Page 527: Siriusxm Travel Link (4C/4C Nav)
MULTIMEDIA • Press the Location button on the navigation bar at the Push the VR button . After the beep, say one of the bottom of the app to bring up a map to locate your following commands: vehicle or send a location to your vehicle’s navigation •...
Page 528: Apple Carplay - If Equipped
526 MULTIMEDIA Apple CarPlay — If Equipped Apple CarPlay allows you to use your voice to interact with Siri through your vehicle’s voice recognition system, and use your smartphone’s data plan to project your iPhone and a number of its apps onto your Uconnect touchscreen.
Page 529: Android Auto - If Equipped
MULTIMEDIA Android Auto — If Equipped Android Auto allows you to use your voice to interact with Android’s best-in-class speech technology through your vehicle’s voice recognition system, and use your smart- phone’s data plan to project your Android powered smart- phone and a number of its apps onto your Uconnect touchscreen.
Page 530 528 MULTIMEDIA Android Auto On 7-inch Display Android Auto On 8.4-inch Display Refer to your Uconnect Owner’s Manual Supplement for further information.
Page 531: General Information
MULTIMEDIA General Information Additional Information The following regulatory statement applies to all Radio © 2017 FCA US LLC. All rights reserved. Mopar and Frequency (RF) devices equipped in this vehicle: Uconnect are registered trademarks and Mopar Owner Connect is a trademark of FCA US LLC. Android is a This device complies with Part 15 of the FCC Rules and trademark of Google Inc.
Page 532: Cd/Dvd Disc Maintenance
530 MULTIMEDIA CD/DVD DISC MAINTENANCE To keep a CD/DVD in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge.
Page 533 CUSTOMER ASSISTANCE CONTENTS SUGGESTIONS FOR OBTAINING SERVICE FOR ▫ Customer Assistance For The Hearing Or YOUR VEHICLE ......532 Speech Impaired (TDD/TTY) .
Page 534: Suggestions For Obtaining Service For Your Vehicle
532 CUSTOMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR IF YOU NEED ASSISTANCE YOUR VEHICLE The manufacturer and its authorized dealer are vitally interested in your satisfaction. We want you to be happy Prepare For The Appointment with our products and services. If you are having warranty work done, be sure to have the right papers with you.
Page 535: Fca Us Llc Customer Center
CUSTOMER ASSISTANCE 533 Any communication to the manufacturer’s customer center In Mexico Contact should include the following information: Av. Prolongacion Paseo de la Reforma, 1240 • Owner’s name and address Sante Fe C.P. 05109 • Owner’s telephone number (home and office) Mexico, D.
Page 536: Customer Assistance For The Hearing Or Speech Impaired (Tdd/Tty)
534 CUSTOMER ASSISTANCE questions about the service contract, call the manufactur- Customer Assistance For The Hearing Or Speech er’s Service Contract National Customer Hotline at 1-800- Impaired (TDD/TTY) 521-9922 (Canadian residents, call (800) 465-2001 English / To assist customers who have hearing difficulties, the (800) 387-9983 French).
Page 537: Warranty Information
CUSTOMER ASSISTANCE 535 REPORTING SAFETY DEFECTS WARNING! In The 50 United States And Washington, D.C. Engine exhaust (internal combustion engines only), If you believe that your vehicle has a defect that could some of its constituents, and certain vehicle compo- cause a crash or cause injury or death, you should nents contain, or emit, chemicals known to the State of immediately inform the National Highway Traffic...
Page 538: In Canada
536 CUSTOMER ASSISTANCE Diagnostic Procedure Manuals In Canada If you believe that your vehicle has a safety defect, you Diagnostic Procedure Manuals are filled with diagrams, should contact the Customer Service Department charts and detailed illustrations. These practical manuals immediately. Canadian customers wish...
Page 539 INDEX...
Page 540 538 INDEX About Your Brakes ......442 Air Conditioning Filter ... . .82, 387, 389, 394 Adaptive Cruise Control (ACC) (Cruise Control) .
Page 541 INDEX 539 Adding Fluid ......410, 450 Brake Fluid ......408, 450 Autostick .
Page 542 540 INDEX Car Washes.......436 Manual ....... .75 Cellular Phone .
Page 543 INDEX 541 Daytime Running Lights ..... .64 Electronic Stability Control (ESC) ....153 Dealer Service .
Page 544 542 INDEX Overheating ......368 Folding Rear Seat......41, 43 Starting .
Page 545: Introduction
INDEX 543 Gear Ranges ......242 Hood Prop ....... .90 Glass Cleaning .
Page 546 544 INDEX Programming Additional Key Fobs ..23, 30 Cruise ......141, 143 Key Fob Battery Service (Remote Keyless Entry) .
Page 547 INDEX 545 Load Shed Exterior Folding ......59 Battery Saver Mode ..... . .130 Heated .
Page 548 546 INDEX Oil Filter, Change ......387 Mirrors ....... .60 Oil Filter, Selection.
Page 549 INDEX 547 Rear Cross Path......169 Restraints, Child ......206 Rear Cupholder.
Page 550 548 INDEX Seat Belts ......181, 224 Arm The System ......32 Adjustable Shoulder Belt .
Page 551 INDEX 549 Accel/Decel (ACC Only) ....263 Sway Control, Trailer ......157 Cancel .
Page 552 550 INDEX Quality Grading ......434 Trailer Towing......325 Radial .
Page 553 INDEX 551 Vanity Mirrors ......62 Down ....... . .84 Vehicle Identification Number (VIN) .
Page 555 The antenna cable should be as short as practical and INSTALLATION OF RADIO TRANSMITTING routed away from the vehicle wiring when possible. Use EQUIPMENT Special design considerations are incorporated into this only fully shielded coaxial cable. vehicle’s electronic system to provide immunity to radio Carefully match the antenna and cable to the radio to frequency signals.

Jeep Grand Cherokee SRT 2018 Owner's Manual

Introduction

Graphical

Getting to Know Your Vehicle

Getting to Know Your Instrument Panel

Safety

Starting and Operating

In Case of Emergency

Servicing and Maintenance

Quick Links

Chapters

Related Manuals for Jeep Grand Cherokee SRT 2018

Summary of Contents for Jeep Grand Cherokee SRT 2018