Page 1 Grand Cherokee 2 0 1 7 O W N E R ’ S M A N U A L...
Page 2 VEHICLES SOLD IN CANADA This manual illustrates and describes the operation of With respect to any Vehicles Sold in Canada, the name FCA features and equipment that are either standard or op- US LLC shall be deemed to be deleted and the name FCA tional on this vehicle.
Page 3 TABLE OF CONTENTS SECTION PAGE INTRODUCTION ..............3 GRAPHICAL TABLE OF CONTENTS .
Page 5: Table Of Contents
INTRODUCTION CONTENTS INTRODUCTION ......4 ROLLOVER WARNING .....6 HOW TO USE THIS MANUAL .
Page 6: Introduction
When it comes to service, remember that your authorized on different road surfaces. Your driving skills will improve dealer knows your Jeep® vehicle best, has factory-trained with experience. When driving off-road, or working the technicians and genuine MOPAR® parts, and cares about vehicle, don’t overload the vehicle, or expect the vehicle to...
Page 7: How To Use This Manual
INTRODUCTION HOW TO USE THIS MANUAL The detailed index at the back of this Owner’s Manual contains a complete listing of all subjects. Essential Information Symbols Consult the Table of Contents to determine which section contains the information you desire. Consult the following table for a description of the symbols that may be used on your vehicle or throughout this Since the specification of your vehicle depends on the items...
Page 8: Rollover Warning
6 INTRODUCTION ROLLOVER WARNING Utility vehicles have a significantly higher rollover rate than other types of vehicles. This vehicle has a higher ground clearance and a higher center of gravity than many passenger vehicles. It is capable of performing better in a wide variety of off-road applications.
Page 9: Warnings And Cautions
INTRODUCTION WARNINGS AND CAUTIONS VEHICLE MODIFICATIONS/ALTERATIONS This Owner’s Manual contains WARNINGS against oper- WARNING! ating procedures that could result in a collision, bodily injury and/or death. It also contains CAUTIONS against Any modifications or alterations to this vehicle could procedures that could result in damage to your vehicle. If seriously affect its roadworthiness and safety and may you do not read this entire Owner’s Manual, you may miss lead to a collision resulting in serious injury or death.
Page 11 GRAPHICAL TABLE OF CONTENTS CONTENTS FRONT VIEW ......10 INSTRUMENT PANEL .....12 REAR VIEW.
Page 12: Front View
10 GRAPHICAL TABLE OF CONTENTS FRONT VIEW Front View 1 — Doors 4 — Wheels/Tires 2 — Exterior Mirrors 5 — Headlights 3 — Windshield 6 — Hood/Engine Compartment...
Page 13: Rear View
GRAPHICAL TABLE OF CONTENTS 11 REAR VIEW Rear View 1 — Rear Lights 2 — Rear Windshield Wiper 3 — Liftgate...
Page 14: Instrument Panel
12 GRAPHICAL TABLE OF CONTENTS INSTRUMENT PANEL Instrument Panel 1 — Air Vents 4 — Instrument Cluster 2 — Multifunction Lever 5 — Paddle Shifter 3 — Steering Wheel 6 — Glove Compartment...
Page 15: Interior
GRAPHICAL TABLE OF CONTENTS 13 INTERIOR Interior Features 1 — Power Window Switches 4 — Climate Controls 2 — Seats 5 — Switch Panel 3 — Transmission Gear Selector 6 — Uconnect Radio...
Page 17 GETTING TO KNOW YOUR VEHICLE CONTENTS ▫ General Information .....30 KEYS ....... . .20 ▫...
Page 18 16 GETTING TO KNOW YOUR VEHICLE ▫ Keyless Enter-N-Go — Passive Entry ..36 MIRRORS ......58 ▫...
Page 19 GETTING TO KNOW YOUR VEHICLE 17 ▫ Parking Lights And Panel Lights ... . .64 ▫ Intermittent Wiper System ....72 ▫...
Page 20 18 GETTING TO KNOW YOUR VEHICLE ▫ Wind Buffeting ......89 LIFTGATE ......94 ▫...
Page 21 GETTING TO KNOW YOUR VEHICLE 19 ▫ Electrical Power Outlets ....116 INTERNAL EQUIPMENT ....109 ▫...
Page 22: Keys
20 GETTING TO KNOW YOUR VEHICLE KEYS Your vehicle uses a keyless ignition system. The ignition system consists of a key fob with Remote Keyless Entry (RKE) and a START/STOP push button ignition system. The Remote Keyless Entry system consists of a key fob and Keyless Enter-N-Go feature.
Page 23 GETTING TO KNOW YOUR VEHICLE 21 1st Push Of Key Fob Unlock Button This feature lets you program the system to unlock either the driver’s door or all doors on the first push of the unlock button on the key fob. To change the current setting, refer to “Uconnect Settings”...
Page 24 22 GETTING TO KNOW YOUR VEHICLE Vehicles Equipped With Keyless Enter-N-Go — Passive Entry If one or more doors are open, or the liftgate is open, the doors will lock. The doors will unlock again automatically if the key is left inside the passenger compartment, other- wise the doors will stay locked.
Page 25 GETTING TO KNOW YOUR VEHICLE 23 Emergency Key Removal Separating Case With A Coin 2. Insert the tip of the emergency key or a #2 flat blade screwdriver into the slot and gently pry the two halves of the key fob apart. Make sure not to damage the seal during removal.
Page 26 24 GETTING TO KNOW YOUR VEHICLE Programming Additional Key Fobs Programming the key fob may be performed by an autho- rized dealer. Request For Additional Key Fobs NOTE: Only key fobs that are programmed to the vehicle electronics can be used to start and operate the vehicle. Once a key fob is programmed to a vehicle, it cannot be programmed to any other vehicle.
Page 27: Ignition Switch
GETTING TO KNOW YOUR VEHICLE 25 IGNITION SWITCH Models With Keyless Enter-N-Go — Passive Entry This feature allows the driver to operate the ignition switch with the push of a button as long as the key fob is in the passenger compartment.
Page 28: Vehicle On Message
26 GETTING TO KNOW YOUR VEHICLE WARNING! (Continued) • Driving position. • Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may • All the electrical devices are available. cause serious injury or death. START •...
Page 29: Remote Starting System - If Equipped
GETTING TO KNOW YOUR VEHICLE 27 NOTE: The power window switches and power sunroof (if WARNING! (Continued) equipped) will remain active up to ten minutes after the ignition of a vehicle equipped with Keyless Enter- ignition is cycled to the OFF position. Opening either front N-Go in the ON/RUN mode.
Page 30: How To Use Remote Start
28 GETTING TO KNOW YOUR VEHICLE heated steering wheel in temperatures below 40° F (4.4° C). How To Use Remote Start Refer to “Front Heated Seats” and “Front Ventilated Seats” • Push Remote Start button on the key fob twice in “Seats”...
Page 31: Remote Start Abort Message
GETTING TO KNOW YOUR VEHICLE 29 • System not disabled from previous remote start event • Remote Start Cancelled — System Fault • Vehicle alarm system indicator flashing • Remote Start Disabled — Start Vehicle To Reset • Ignition in STOP/OFF position The instrument cluster display message stays active until the ignition is turned to the ON/RUN position.
Page 32: To Exit Remote Start Mode Without Driving The Vehicle
30 GETTING TO KNOW YOUR VEHICLE • The engine can be started two consecutive times (two Comfort Systems — If Equipped 15-minute cycles) with the key fob. However, the igni- When Remote Start is activated, Auto-Comfort will work tion must be placed in the ON/RUN position before you anytime the temperature conditions are correct.
Page 33: Sentry Key
GETTING TO KNOW YOUR VEHICLE 31 2. This device must accept any interference received, in- a bulb check. If the light remains on after the bulb check, it cluding interference that may cause undesired opera- indicates that there is a problem with the electronics. In tion.
Page 34: Customer Key Programming
32 GETTING TO KNOW YOUR VEHICLE Customer Key Programming General Information Programming key fobs may be performed at an authorized The following regulatory statement applies to all radio dealer. frequency (RF) devices equipped in this vehicle: This device complies with Part 15 of the FCC Rules and Replacement Keys with Industry Canada license-exempt RSS standard(s).
Page 35: Rearming Of The System
GETTING TO KNOW YOUR VEHICLE 33 • The horn will pulse exterior zone (refer to Keyless Enter-N-Go — Passive Entry in Getting To Know Your Vehicle for further • The turn signals will flash information). • The vehicle security light in the instrument cluster will •...
Page 36: Security System Manual Override
34 GETTING TO KNOW YOUR VEHICLE the vehicle security alarm. If someone enters the vehicle Tamper Alert through the liftgate and opens any door, the alarm will If something has triggered the Vehicle Security Alarm in sound. your absence, the horn will sound three times and the •...
Page 37: Power Door Locks
GETTING TO KNOW YOUR VEHICLE 35 Power Door Locks WARNING! The power door lock switches are located on each front • For personal security and safety in the event of a door panel. Push the switch to lock or unlock the doors. collision, lock the vehicle doors before you drive as well as when you park and leave the vehicle.
Page 38: Keyless Enter-N-Go - Passive Entry
36 GETTING TO KNOW YOUR VEHICLE If a rear door is locked, it cannot be opened from inside the To Unlock From The Driver Or Passenger Side vehicle without first unlocking the door. The door may be With a valid Passive Entry key fob within 5 ft (1.5 m) of the unlocked manually by raising the lock knob.
Page 39 GETTING TO KNOW YOUR VEHICLE 37 • A lock request is made by the Passive Entry door handle To Unlock From The Passenger Side while a door is open. With a valid Passive Entry key fob within 5 ft (1.5 m) of the •...
Page 40 38 GETTING TO KNOW YOUR VEHICLE To Lock The Vehicle’s Doors And Liftgate With one of the vehicle’s Passive Entry key fob within 5 ft (1.5 m) of the driver or passenger front door handles, pushing the passive entry lock button will lock the vehicle. DO NOT grab the door handle, when pushing the door handle lock button.
Page 41 GETTING TO KNOW YOUR VEHICLE 39 • The Passive Entry system will not operate if the key fob battery is dead. The vehicle doors can also be locked by using the lock button located on the vehicle’s interior door panel. To Unlock/Enter The Liftgate The liftgate passive entry unlock feature is built into the electronic liftgate release.
Page 42: Automatic Unlock Doors On Exit
40 GETTING TO KNOW YOUR VEHICLE Automatic Unlock Doors On Exit The doors will unlock automatically on vehicles with power door locks if: 1. The Automatic Unlock Doors On Exit feature is enabled. 2. All doors are closed. 3. The transmission gear selector was not in PARK, then is placed in PARK.
Page 43: Seats
GETTING TO KNOW YOUR VEHICLE 41 • For emergency exit with the system engaged, rotate the WARNING! (Continued) door lock button until the lock indicator is hidden • Do not allow people to ride in any area of your (unlocked position), roll down the window, and open vehicle that is not equipped with seats and seat belts.
Page 44 42 GETTING TO KNOW YOUR VEHICLE Adjusting The Seat Up Or Down The height of the seats can be adjusted up or down. Pull upward or push downward on the seat switch, the seat will move in the direction of the switch. Release the switch when the desired position has been reached.
Page 45: Manual Adjustment (Rear Seats)
GETTING TO KNOW YOUR VEHICLE 43 support. Pushing upward or downward on the switch will WARNING! (Continued) raise and lower the position of the support. control which could cause a collision and serious injury or death. • Seats should be adjusted before fastening the seat belts and while the vehicle is parked.
Page 46: Getting To Know Your Vehicle 15
44 GETTING TO KNOW YOUR VEHICLE 1. Pull upward on the release lever to release the seat. 2. Fold the rear seat completely forward. Rear Seat Release Rear Seat Folded NOTE: NOTE: You may experience deformation in the seat cush- ion from the seat belt buckles if the seats are left folded for •...
Page 47: Driver Memory Seat - If Equipped
GETTING TO KNOW YOUR VEHICLE 45 locking, you will have difficulty returning the seat to its proper position. WARNING! • Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers.
Page 48 46 GETTING TO KNOW YOUR VEHICLE steering column (if equipped) and a set of desired radio station presets. Your key fob can also be programmed to recall the same positions when the unlock button is pushed. NOTE: Your vehicle is equipped with two key fobs, one key fob can be linked to memory position 1 and the other key fob can be linked to memory position 2.
Page 49 GETTING TO KNOW YOUR VEHICLE 47 3. Push and release the set (S) button on the memory To program your key fobs, perform the following: switch. 1. Cycle the vehicle’s ignition to the OFF position. 4. Within five seconds, push and release either of the 2.
Page 50 48 GETTING TO KNOW YOUR VEHICLE Memory Position Recall cancelled, the driver’s seat and steering column (if equipped) stop moving. A delay of one second will occur NOTE: The vehicle must be in PARK to recall memory before another recall can be selected. positions.
Page 51: Heated Seats - If Equipped
GETTING TO KNOW YOUR VEHICLE 49 Each stored memory setting will have an associated Easy WARNING! (Continued) Entry and Easy Exit position. This may cause the seat heater to overheat. Sitting in NOTE: The Easy Entry/Exit feature is not enabled when a seat that has been overheated could cause serious the vehicle is delivered from the factory.
Page 52 50 GETTING TO KNOW YOUR VEHICLE from HI to LO, indicating the change. The LO-level setting WARNING! (Continued) will turn OFF automatically after approximately 45 min- when using the seat heater. It may cause burns even utes. at low temperatures, especially if used for long NOTE: periods of time.
Page 53 GETTING TO KNOW YOUR VEHICLE 51 of operation. Then, the heat output will drop to the normal HI-level. If the HI-level setting is selected, the system will automatically switch to LO-level after approximately 60 minutes of continuous operation. At that time, the number of indicator lights changes from two to one, indicating the change.
Page 54: Front Ventilated Seats - If Equipped
52 GETTING TO KNOW YOUR VEHICLE Front Ventilated Seats — If Equipped This feature can be programmed through the Uconnect system. Refer to “Uconnect Settings” in “Multimedia” for Located in the seat cushion and seat back are fans that further information. draw the air from the passenger compartment and move air through fine perforations in the seat cover to help keep HEAD RESTRAINTS...
Page 55: Supplemental Active Head Restraints - Front Seats
GETTING TO KNOW YOUR VEHICLE 53 Supplemental Active Head Restraints — Front To raise the head restraint, pull upward on the head restraint. To lower the head restraint, push the adjustment Seats button, located at the base of the head restraint, and push Active Head Restraints are passive, deployable compo- downward on the head restraint.
Page 56 54 GETTING TO KNOW YOUR VEHICLE For comfort the Active Head Restraints can be tilted forward and rearward. To tilt the head restraint closer to the back of your head, pull forward on the bottom of the head restraint. Push rearward on the bottom of the head restraint to move the head restraint away from your head.
Page 57: Head Restraints - Rear Seats
GETTING TO KNOW YOUR VEHICLE 55 normal position when the rear seat is raised. After return- WARNING! ing either seat to its upright position, raise the head • All occupants, including the driver, should not oper- restraint until it locks in place. The outboard head re- straints are not removable.
Page 58: Steering Wheel
56 GETTING TO KNOW YOUR VEHICLE WARNING! Sitting in a seat with the head restraint in its lowered position could result in serious injury or death in a collision. Always make sure the outboard head re- straints are in their upright positions when the seat is to be occupied.
Page 59: Heated Steering Wheel - If Equipped
GETTING TO KNOW YOUR VEHICLE 57 • Press the heated steering wheel button a second time WARNING! to turn the heating element off. Do not adjust the steering column while driving. NOTE: The engine must be running for the heated steering Adjusting the steering column while driving or driv- wheel to operate.
Page 60: Mirrors
58 GETTING TO KNOW YOUR VEHICLE MIRRORS Automatic Dimming Mirror — If Equipped The mirror head can be adjusted up, down, left, and right for various drivers. The mirror should be adjusted to center on the view through the rear window. This mirror automatically adjusts for headlight glare from vehicles behind you.
Page 61: Outside Automatic Dimming Mirrors - If
GETTING TO KNOW YOUR VEHICLE 59 Power Mirrors WARNING! The power mirror switch is located on the driver’s side Vehicles and other objects seen in an outside convex door trim panel. mirror will look smaller and farther away than they The power mirror controls consist of mirror select buttons really are.
Page 62: Tilt Side Mirrors In Reverse (Available With Memory Seat Only) - If Equipped
60 GETTING TO KNOW YOUR VEHICLE Power mirror preselected positions can be controlled by NOTE: The Tilt Side Mirrors in Reverse feature is not the optional Memory Seat Feature. Refer to “Driver turned on when delivered from the factory. The Tilt Side Memory Seat”...
Page 63 GETTING TO KNOW YOUR VEHICLE 61 NOTE: The Automatic Fold/Unfold Mirrors feature is not turned on when delivered from the factory. The Automatic Fold/Unfold Mirrors feature can be turned on and off using the Uconnect System. Refer to “Uconnect Settings” in “Multimedia”...
Page 64: Illuminated Vanity Mirrors
62 GETTING TO KNOW YOUR VEHICLE Illuminated Vanity Mirrors Sun Visor “Slide-On-Rod” Feature — If Equipped To access an illuminated vanity mirror, flip down one of the The sun visor “Slide-On-Rod” feature allows for additional visors. flexibility in positioning the sun visor to block out the sun. Lift the cover to reveal the mirror.
Page 65: Automatic Headlights - If Equipped
GETTING TO KNOW YOUR VEHICLE 63 switch controls the operation of the headlights, parking NOTE: lights, instrument panel lights, cargo lights and fog lights • Your vehicle is equipped with plastic headlight and fog (if equipped). light (if equipped) lenses that are lighter and less sus- ceptible to stone breakage than glass lights.
Page 66: Automatic Headlight Leveling - Hid Headlights
64 GETTING TO KNOW YOUR VEHICLE position. To turn the automatic headlights off, turn the system is on. This feature is programmable through the headlight switch out of the AUTO position. Uconnect system screen. Refer to “Uconnect Settings” in “Multimedia” for further information. NOTE: The engine must be running before the headlights If your vehicle is equipped with a “Rain Sensitive Wiper will turn on in the Automatic Mode.
Page 67: Lights-On Reminder
GETTING TO KNOW YOUR VEHICLE 65 NOTE: This feature can be programmed through the Uconnect system. Refer to “Uconnect Settings” in “Multi- media” for further information. Lights-On Reminder If the headlights, parking lights or cargo lights are left on after the ignition is turned OFF, a chime will sound when the driver’s door is opened.
Page 68: Multifunction Lever
66 GETTING TO KNOW YOUR VEHICLE Multifunction Lever NOTE: If either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside The multifunction lever is located on the left side of the light bulb.
Page 69: Automatic High Beam - If Equipped
GETTING TO KNOW YOUR VEHICLE 67 Automatic High Beam — If Equipped lever 6 full on/off cycles within 10 seconds of ignition ON. System will return to default setting upon ignition The Automatic High Beam Headlamp Control system off. provides increased forward lighting at night by automat- ing high beam control through the use of a digital camera If the windshield or Automatic High Beam Headlamp mounted on the inside rearview mirror.
Page 70: Interior Lights
68 GETTING TO KNOW YOUR VEHICLE INTERIOR LIGHTS Courtesy Lights Courtesy and dome lights are turned on when the front The courtesy lights can be turned on by pushing the top doors are opened or when the dimmer control (rotating corner of the lens.
Page 71 GETTING TO KNOW YOUR VEHICLE 69 Front Map/Reading Lights — If Equipped visibility. To turn the lights off, push the switch a second time. The lights will also turn on when the unlock button The front map/reading lights are mounted in the overhead on the remote keyless entry key fob is pushed.
Page 72 70 GETTING TO KNOW YOUR VEHICLE Dimmer Controls Ambient Light — If Equipped The brightness of the instrument panel lighting can be The overhead console is equipped with an ambient light regulated by rotating the dimmer control up (brighter) or feature.
Page 73: Windshield Wipers And Washers
GETTING TO KNOW YOUR VEHICLE 71 WINDSHIELD WIPERS AND WASHERS wiper operation and the sixth detent for high wiper operation. The windshield wiper/washer controls are located on the multifunction lever on the left side of the steering column. The front wipers are operated by rotating a switch, located on the end of the lever.
Page 74: Intermittent Wiper System
72 GETTING TO KNOW YOUR VEHICLE Intermittent Wiper System Windshield Washer Operation Use one of the four intermittent wiper settings when To use the washer, push on the end of the lever (toward the weather conditions make a single wiping cycle, with a steering wheel) and hold while spray is desired.
Page 75: Mist
GETTING TO KNOW YOUR VEHICLE 73 WARNING! Sudden loss of visibility through the windshield could lead to a collision. You might not see other vehicles or other obstacles. To avoid sudden icing of the wind- shield during freezing weather, warm the windshield with the defroster before and during windshield washer use.
Page 76: Rear Window Wiper/Washer
74 GETTING TO KNOW YOUR VEHICLE sensitive, and wiper delay position four is the most sensi- until the wiper switch is moved, vehicle speed is greater tive. Setting three should be used for normal rain condi- than 3 mph (5 km/h), or the outside temperature is tions.
Page 77 GETTING TO KNOW YOUR VEHICLE 75 operate as long as the switch is held. Upon release of the switch, the wipers will resume the continuous rear wiper operation. When this rotary control is in the OFF position, rotating it downward will activate the rear washer pump which will continue to operate as long as the switch is held.
Page 78: Headlight Washers - If Equipped
76 GETTING TO KNOW YOUR VEHICLE HEADLIGHT WASHERS — IF EQUIPPED NOTE: After turning the ignition switch and headlights ON, the headlight washers will operate on the first spray of The multifunction lever operates the headlight washers the windshield washer and then every eleventh spray after when the ignition switch is in the ON position and the that.
Page 79 GETTING TO KNOW YOUR VEHICLE 77 Uconnect 8.4/8.4 NAV Automatic Climate Controls...
Page 80 78 GETTING TO KNOW YOUR VEHICLE Control Descriptions Icon Description MAX A/C Button Press and release to change the current setting, the indicator illuminates when MAX A/C is on. Performing this function again will cause the MAX A/C operation to switch into manual mode and the MAX A/C indicator will turn off.
Page 81 GETTING TO KNOW YOUR VEHICLE 79 Icon Description AUTO Button Automatically controls the interior cabin temperature by adjusting airflow distribution and amount. Toggling this function will cause the system to switch between manual mode and auto- matic modes. Refer to “Automatic Operation” for more information. Front Defrost Button The Front Defrost button changes the current airflow setting to Defrost mode.
Page 82 80 GETTING TO KNOW YOUR VEHICLE Icon Description SYNC Button Press the SYNC button on the touchscreen to toggle the SYNC feature on/off. The SYNC indica- tor is illuminated when this feature is enabled. SYNC is used to synchronize the passenger tem- perature setting with the driver temperature setting.
Page 83 GETTING TO KNOW YOUR VEHICLE 81 Icon Description Bi-Level Mode Bi-Level Mode Air comes from the instrument panel outlets and floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. NOTE: Bi-Level mode is designed under comfort conditions to provide cooler air out of the panel out- lets and warmer air from the floor outlets.
Page 84 82 GETTING TO KNOW YOUR VEHICLE NOTE: CAUTION! • If fog or mist appears on the windshield or side glass, Failure to follow these cautions can cause damage to select Defrost mode and increase blower speed if the heating elements: needed.
Page 85: Automatic Temperature Control (Atc) - If Equipped
GETTING TO KNOW YOUR VEHICLE 83 interior air by pressing the Recirculation control button. temperature control buttons. Once the desired tempera- The recirculation indicator will illuminate when this button ture is displayed, the system will achieve and automati- is selected. Press the button a second time to turn off the cally maintain that comfort level.
Page 86: Operating Tips
84 GETTING TO KNOW YOUR VEHICLE Manual Operation Override Winter Operation This system offers a full complement of manual override To ensure the best possible heater and defroster perfor- features. The AUTO symbol in the front ATC display will mance, make sure the engine cooling system is functioning be turned off when the system is being used in the manual properly and the proper amount, type, and concentration mode.
Page 87 GETTING TO KNOW YOUR VEHICLE 85 Window Fogging collected in the air intake may reduce airflow, and if they enter the plenum, they could plug the water drains. In Vehicle windows tend to fog on the inside in mild, rainy winter months, make sure the air intake is clear of ice, and/or humid weather.
Page 88 86 GETTING TO KNOW YOUR VEHICLE Operating Tips Chart...
Page 89: Windows
GETTING TO KNOW YOUR VEHICLE 87 WINDOWS NOTE: For vehicles equipped with the Uconnect, the power window switches will remain active for up to 10 Power Window Controls minutes after the ignition is cycled to the OFF position. The window controls on the driver’s door control all the Opening either front door will cancel this feature.
Page 90: Auto-Up Feature With Anti-Pinch Protection
88 GETTING TO KNOW YOUR VEHICLE To open the window part way, push the window switch WARNING! down briefly and release it when you want the window to stop. There is no anti-pinch protection when the window is almost closed. To avoid personal injury be sure to clear To stop the window from going all the way down during your arms, hands, fingers and all objects from the the Auto-Down operation, pull up on the switch briefly.
Page 91: Getting To Know Your Vehicle 89
GETTING TO KNOW YOUR VEHICLE 89 push and release the window lockout button again (the buffeting. If the buffeting occurs with the sunroof open, indicator light on the button will turn back off). adjust the sunroof opening to minimize the buffeting or open any window.
Page 92: Opening Sunroof
90 GETTING TO KNOW YOUR VEHICLE Opening Sunroof WARNING! The sunroof has two programmed automatic stops for the • Never leave children unattended in a vehicle, or with sunroof open position; a comfort stop position and a full access to an unlocked vehicle. Never leave the key open position.
Page 93: Closing Sunroof
GETTING TO KNOW YOUR VEHICLE 91 NOTE: If the sunshade is in the closed position when switch a second time from the halfway position and the Express or Manual Open operation is initiated the sun- shade will automatically open to the full open position and shade will automatically open to the half open position stop automatically.
Page 94: Venting Sunroof - Express
92 GETTING TO KNOW YOUR VEHICLE NOTE: If the sunroof is open, the shade will close to the in the path of the sunroof is detected, the sunroof will half-open position. Pushing the shade close button again automatically retract. Remove the obstruction if this oc- will automatically close both the sunroof and shade com- curs.
Page 95: Ignition Off Operation
GETTING TO KNOW YOUR VEHICLE 93 Ignition Off Operation HOOD NOTE: To Open The Hood • The power sunroof switch can remain active in Acces- To open the hood, two latches must be released. sory Delay for up to approximately ten minutes after the 1.
Page 96: Closing The Hood
94 GETTING TO KNOW YOUR VEHICLE 2. Reach under the hood, move safety latch to the left and WARNING! lift the hood. Be sure the hood is fully latched before driving your vehicle. If the hood is not fully latched, it could open when the vehicle is in motion and block your vision.
Page 97 GETTING TO KNOW YOUR VEHICLE 95 To Unlock/Enter The Liftgate The liftgate may be released in several ways: • Key fob • Outside handle • Button on Overhead Console The liftgate passive entry unlock feature is built into the electronic liftgate release. With a valid Passive Entry Key Fob within 5 ft (1.5 m) of the liftgate, push the electronic liftgate release to open with one fluid motion.
Page 98: Closing
96 GETTING TO KNOW YOUR VEHICLE NOTE: Before closing the liftgate, make sure to be in WARNING! possession of the key because the liftgate may be locked. Driving with the liftgate open can allow poisonous To Lock The Liftgate exhaust gases into your vehicle. You and your passen- With a valid Passive Entry key fob within 5 ft (1.5 m) of the gers could be injured by these fumes.
Page 99 GETTING TO KNOW YOUR VEHICLE 97 trim panel, near the liftgate opening. If the liftgate is in WARNING! motion, pushing the liftgate button located on the left rear trim panel will reverse the liftgate. During power operation, personal injury or cargo damage may occur.
Page 100: Cargo Area Features
98 GETTING TO KNOW YOUR VEHICLE • If the electronic liftgate release is pushed while the Cargo Area Features power liftgate is closing, the liftgate will reverse to the Rechargeable Flashlight full open position. The rechargeable flashlight is mounted on the left side of •...
Page 101 GETTING TO KNOW YOUR VEHICLE 99 To operate the flashlight, push the switch once for high, Cargo Storage Bins twice for low, and a third time to return to off. There are up to four removable storage bins located in the rear cargo area.
Page 102 100 GETTING TO KNOW YOUR VEHICLE Two additional storage bins are located under the load floor. To access the lower storage bins, raise the load floor and attach the tether strap (attached to the bottom of the load floor) to the liftgate opening. Rear Lower Storage Bins Retractable Cargo Area Cover —...
Page 103 GETTING TO KNOW YOUR VEHICLE 101 3. The liftgate may be opened with the cargo cover in Rear Cargo Tie-Downs place. The rear cargo tie-downs, located on the cargo area floor, should be used to safely secure loads when the vehicle is moving.
Page 104: Garage Door Opener - If Equipped
102 GETTING TO KNOW YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) • Always place cargo evenly on the cargo floor. Put only, not for passengers, who should sit in seats and use seat belts. heavier objects as low and as far forward as possible. •...
Page 105: Before You Begin Programming Homelink
GETTING TO KNOW YOUR VEHICLE 103 The HomeLink buttons, located on the overhead console, battery be placed in the hand-held transmitter of the device designate the three different HomeLink channels. The that is being programmed to the HomeLink system. HomeLink indicator is located above the center button. To erase the channels place the ignition in the ON/RUN position and push and hold the two outside HomeLink buttons (I and III) for up to 20 seconds or until the orange...
Page 106 104 GETTING TO KNOW YOUR VEHICLE 4. Continue to hold both buttons and observe the indicator light. The HomeLink indicator will flash slowly and then rapidly after HomeLink has received the frequency signal from the hand-held transmitter. Release both buttons after the indicator light changes from slow to rapid.
Page 107 GETTING TO KNOW YOUR VEHICLE 105 To program the remaining two HomeLink buttons, repeat 3. Push and hold the Homelink button you want to each step for each remaining button. DO NOT erase the program while you push and hold the hand-held trans- channels.
Page 108: Canadian/Gate Operator Programming
106 GETTING TO KNOW YOUR VEHICLE 2. Push and hold the desired HomeLink button until the 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) indicator light begins to flash after 20 seconds. Do not away from the HomeLink button you wish to program release the button.
Page 109: Using Homelink
GETTING TO KNOW YOUR VEHICLE 107 If you unplugged the garage door opener/device for Security programming, plug it back in at this time. It is advised to erase all channels before you sell or turn in your vehicle. Reprogramming A Single HomeLink Button (Canadian/ Gate Operator) To do this, push and hold the two outside buttons for 20 To reprogram a channel that has been previously trained,...
Page 110: General Information
108 GETTING TO KNOW YOUR VEHICLE General Information WARNING! This device complies with FCC rules Part 15 and Industry • Vehicle exhaust contains carbon monoxide, a danger- Canada RSS-210. Operation is subject to the following two ous gas. Do not run your vehicle in the garage while conditions: programming the transceiver.
Page 111: Internal Equipment
GETTING TO KNOW YOUR VEHICLE 109 INTERNAL EQUIPMENT To open the glove compartment, pull outward on the latch and lower the glove compartment door. Storage Glove Compartment The glove compartment is located on the passenger side of the instrument panel. Opened Glove Compartment Glove Compartment...
Page 112 110 GETTING TO KNOW YOUR VEHICLE Door Storage Console Features Large storage areas are built into the door panels for easy The center console contains both an upper and a lower access. storage area. Door Panel Storage Storage Compartment To open the upper storage compartment, pull upward on the small latch located on the lid.
Page 113 GETTING TO KNOW YOUR VEHICLE 111 Storage Compartment Latches Lower Storage Compartment Lift upward on the larger of the latches to access the lower Your vehicle may have an optional CD or DVD player storage compartment. located in the center console.
Page 114 112 GETTING TO KNOW YOUR VEHICLE Overhead Console The overhead console contains courtesy/reading lights and storage for sunglasses. Universal Garage Door Opener (HomeLink), power liftgate and power sunroof switches may also be included, if equipped. Lower Storage Compartment CD/DVD Player — If Equipped WARNING! Do not operate this vehicle with a console compart-...
Page 115 GETTING TO KNOW YOUR VEHICLE 113 Front Map/Reading Lights — If Equipped To turn the lights off, push the switch a second time. The lights also turn on when a door is opened. The lights will Lights are mounted in the overhead console. Each light can also turn on when the unlock button on the key fob is be turned on by pushing the switch on either side of the pushed.
Page 116 114 GETTING TO KNOW YOUR VEHICLE Courtesy Lights Sunglasses Bin Door The courtesy lights can be turned on by pushing the top At the front of the console a compartment is provided for corner of the lens. To turn the lights off, push the lens a the storage of a pair of sunglasses.
Page 117: Cupholders
GETTING TO KNOW YOUR VEHICLE 115 Cupholders There are two cupholders for the front seat passengers located in the center console. Rear Cupholders Sun Visor “Slide-On-Rod” Feature — If Equipped The sun visor “Slide-On-Rod” feature allows for additional flexibility in positioning the sun visor to block out the sun. Front Cupholders There are two cupholders for the rear seat passengers 1.
Page 118: Electrical Power Outlets
116 GETTING TO KNOW YOUR VEHICLE Electrical Power Outlets CAUTION! (Continued) Your vehicle is equipped with 12 Volt (15 Amp) power this will damage the outlet and blow the fuse. Im- outlets that can be used to power cellular phones, small proper use of the power outlet can cause damage not electronics and other low powered electrical accessories.
Page 119 GETTING TO KNOW YOUR VEHICLE 117 In addition to the front power outlet, there is also a power The rear power outlet is located in the right rear cargo area. outlet located in the storage area of the center console. Rear Power Outlet Center Console Outlet NOTE: The rear power outlet can be switched from...
Page 120 118 GETTING TO KNOW YOUR VEHICLE Power Outlet Right Rear Quarter Panel Fuse Power Outlet Fuse Locations 1 — F104 Fuse 20 Amp Yellow Power Outlet Console Bin 2 — F90–F91 Fuse 20 Amp Yellow Power Outlet Right Rear Quarter Panel 3 —...
Page 121: Power Inverter - If Equipped
GETTING TO KNOW YOUR VEHICLE 119 Power Inverter — If Equipped WARNING! (Continued) There is a 115 Volt, 150 Watt inverter outlet located on the • Close the lid when not in use and while driving the back of the center console to convert DC current to AC vehicle.
Page 122: Roof Luggage Rack - If Equipped
120 GETTING TO KNOW YOUR VEHICLE inverter should automatically reset. To avoid overloading capacity of the vehicle. Be sure the total load of cargo inside the circuit, check the power ratings on electrical devices the vehicle plus that on the external rack does not exceed prior to using the inverter.
Page 123 GETTING TO KNOW YOUR VEHICLE 121 WARNING! CAUTION! (Continued) • To avoid damage to the roof rack and vehicle, do not Cargo must be securely tied down before driving your exceed the maximum roof rack load capacity of 150 lb vehicle.
Page 125 GETTING TO KNOW YOUR INSTRUMENT PANEL CONTENTS INSTRUMENT CLUSTER ....124 WARNING/INDICATOR LIGHTS AND MESSAGES ......140 ▫...
Page 126: Instrument Cluster
124 GETTING TO KNOW YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER SRT Instrument Cluster...
Page 127: Instrument Cluster Descriptions
GETTING TO KNOW YOUR INSTRUMENT PANEL 125 Instrument Cluster Descriptions CAUTION! 1. Speedometer Driving with a hot engine cooling system could dam- • Indicates vehicle speed. age your vehicle. If the temperature gauge reads “H” pull over and stop the vehicle. Idle the vehicle with the 2.
Page 128: Instrument Cluster Display
126 GETTING TO KNOW YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DISPLAY Your vehicle may be equipped with an instrument cluster display, which offers useful information to the driver. With the ignition in the STOP/OFF position, opening/closing of a door will activate the display for viewing, and display the total miles, or kilometers, in the odometer.
Page 129 GETTING TO KNOW YOUR INSTRUMENT PANEL 127 • Trip • Up Arrow Button • Audio Push and release the up arrow button to scroll upward through the Main Menu items. • Stored Messages • Screen Setup • Down Arrow Button •...
Page 130: Oil Change Reset
128 GETTING TO KNOW YOUR INSTRUMENT PANEL Oil Change Reset 3. Without pushing the brake pedal, push and release the ENGINE START/STOP button once to return the igni- Your vehicle is equipped with an engine oil change indi- tion to the OFF/LOCK position. cator system.
Page 131 GETTING TO KNOW YOUR INSTRUMENT PANEL 129 • Washer Fluid Low • Brake Fluid Low • Oil Pressure Low • Service Electronic Braking System • Oil Change Due • Engine Temperature Hot • Fuel Low • Lights On • Service Anti-lock Brake System •...
Page 132: Instrument Cluster Display Menu Items
130 GETTING TO KNOW YOUR INSTRUMENT PANEL • Remote Start Disabled Start To Reset Instrument Cluster Display Menu Items • Service Air Bag System NOTE: The instrument cluster display menu items display in the center of the instrument cluster. Menu items may •...
Page 133 GETTING TO KNOW YOUR INSTRUMENT PANEL 131 Oil Temperature NOTE: Storage mode will increase the amount the time the vehicle can be parked without the battery discharging Oil Pressure — Gasoline Vehicle Only beyond the point where the vehicle won’t restart. To use Oil Life the vehicle’s key fob, the driver will need to grab a door handle to wake up the vehicle prior to it checking for the...
Page 134 132 GETTING TO KNOW YOUR INSTRUMENT PANEL Performance Features – Reaction Time — If Selected • 0-100 MPH (0-160 km/h) Timer Push and release the up or down arrow button until the SRT icon/title is highlighted in the instrument – Best cluster display.
Page 135 GETTING TO KNOW YOUR INSTRUMENT PANEL 133 • Braking Distance Push the Adaptive Cruise Control (ACC) on/off button (located on the steering wheel) until one of the following – Distance displays in the instrument cluster display: – From Speed Adaptive Cruise Control Off •...
Page 136 134 GETTING TO KNOW YOUR INSTRUMENT PANEL • Driver Override • Range – The display shows the estimated distance (mi or km) that can be traveled with the fuel remaining in • System Off the tank. When the Range value is less than 10 miles •...
Page 137 GETTING TO KNOW YOUR INSTRUMENT PANEL 135 • Average Fuel Economy – Shows the average fuel as needed. The Screen Setup feature allows you to change economy (MPG, L/100 km, or km/L) of Trip A or Trip B what information is displayed in the instrument cluster as since the last reset.
Page 138 136 GETTING TO KNOW YOUR INSTRUMENT PANEL Upper Right Favorite Menus — Equipped • None • Speedometer • Compass • Vehicle Info • Outside Temp (default setting) • Terrain (show/hide) • Time • SRT Performance Pages (show/hide) • Range • Driver Assist (show/hide) •...
Page 139: Battery Saver On/Battery Saver Mode Message - Electrical Load Reduction Actions - If Equipped
GETTING TO KNOW YOUR INSTRUMENT PANEL 137 Diagnostics In cases when the IBS detects charging system failure, or the vehicle battery conditions are deteriorating, electrical Push and release the up or down arrow button load reduction actions will take place to extend the driving until the Diagnostics icon/title is highlighted in the time and distance of the vehicle.
Page 140 138 GETTING TO KNOW YOUR INSTRUMENT PANEL Lights And Messages” located in ”Getting To Know overloaded power outlets +12V, 115V AC, USB ports) Your Instrument Panel” for further information. during certain driving conditions (city driving, towing, frequent stopping). The electrical loads that may be switched off (if equipped), •...
Page 141: Trip Computer
GETTING TO KNOW YOUR INSTRUMENT PANEL 139 What to do when an electrical load reduction action TRIP COMPUTER message is present (“Battery Saver On” or “Battery Saver The Trip Computer is located in the instrument cluster Mode”) display. Push and release the up or down arrow During a trip:...
Page 142: Warning/Indicator Lights And Messages
140 GETTING TO KNOW YOUR INSTRUMENT PANEL Elapsed Time WARNING/INDICATOR LIGHTS AND MESSAGES IMPORTANT: The warning/indicator light switches on in Shows the total elapsed time of travel since the last reset the instrument panel together with a dedicated message when the ignition switch is in the ACC position. Elapsed and/or acoustic signal when applicable.
Page 143: Red Telltale Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL 141 Red Telltale Lights Seat Belt Reminder Warning Light Red Telltale What It Means Light Seat Belt Reminder Warning Light When the ignition switch is first turned to ON/RUN, this light will turn on for four to eight sec- onds as a bulb check.
Page 144 142 GETTING TO KNOW YOUR INSTRUMENT PANEL Brake Warning Light Red Telltale What It Means Light Brake Warning Light This light monitors various brake functions, including brake fluid level and parking brake appli- cation. If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the anti-lock brake system reservoir.
Page 145 GETTING TO KNOW YOUR INSTRUMENT PANEL 143 Operation of the Brake Warning Light can be checked by WARNING! turning the ignition switch from the OFF position to the ON/RUN position. The light should illuminate for ap- Driving a vehicle with the red brake light on is proximately two seconds.
Page 146 144 GETTING TO KNOW YOUR INSTRUMENT PANEL Oil Pressure Warning Light Red Telltale What It Means Light Oil Pressure Warning Light This light indicates low engine oil pressure. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound when this light turns on. Do not operate the vehicle until the cause is corrected.
Page 147 GETTING TO KNOW YOUR INSTRUMENT PANEL 145 Oil Temperature Warning Light Red Telltale What It Means Light Oil Temperature Warning Light This telltale indicates engine oil temperature is high. If the light turns on while driving, stop the ve- hicle and shut off the engine as soon as possible. Battery Charge Warning Light Red Telltale What It Means...
Page 148 146 GETTING TO KNOW YOUR INSTRUMENT PANEL Electronic Throttle Control (ETC) Warning Light Red Telltale What It Means Light Electronic Throttle Control (ETC) Warning Light This light informs you of a problem with the Electronic Throttle Control (ETC) system. If a prob- lem is detected while the engine is running, the light will either stay on or flash depending on the nature of the problem.
Page 149 GETTING TO KNOW YOUR INSTRUMENT PANEL 147 Door Open Warning Light Red Telltale What It Means Light Door Open Warning Light This indicator will illuminate when a door is ajar/open and not fully closed. NOTE: If the vehicle is moving, there will also be a single chime. Liftgate Open Warning Light Red Telltale What It Means...
Page 150 148 GETTING TO KNOW YOUR INSTRUMENT PANEL Transmission Temperature Warning Light Red Telltale What It Means Light Transmission Temperature Warning Light This light indicates that the transmission fluid temperature is running hot. This may occur with se- vere usage. If this light turns on, safely pull over and stop the vehicle. Then, shift the transmission into NEUTRAL and run the engine at idle or faster until the light turns off.
Page 151 GETTING TO KNOW YOUR INSTRUMENT PANEL 149 Hood Open Warning Light Red Telltale What It Means Light Hood Open Warning Light This indicator will illuminate when the hood is ajar/open and not fully closed. Custom Mode SRT Indicator Light Red Telltale Light What It Means Custom Mode SRT Indicator Light This light will turn on when Custom Mode SRT is active.
Page 152: Yellow Telltale Lights
150 GETTING TO KNOW YOUR INSTRUMENT PANEL Yellow Telltale Lights Engine Malfunction Warning Light Yellow Telltale What It Means Light Engine Check/Malfunction Indicator Light (MIL) The Engine Check/Malfunction Indicator Light (MIL) is a part of an Onboard Diagnostic System called OBD II that monitors engine and automatic transmission control systems. The light will illuminate when the ignition is in the ON position before engine start.
Page 153 GETTING TO KNOW YOUR INSTRUMENT PANEL 151 WARNING! CAUTION! A malfunctioning catalytic converter, as referenced Prolonged driving with the Malfunction Indicator above, can reach higher temperatures than in normal Light (MIL) on could cause damage to the engine operating conditions. This can cause a fire if you drive control system.
Page 154 152 GETTING TO KNOW YOUR INSTRUMENT PANEL Electronic Stability Control (ESC) Warning Light Yellow Telltale What It Means Light Electronic Stability Control (ESC) Indicator Light — If Equipped The “ESC Indicator Light” in the instrument cluster will come on when the ignition switch is turned to the ON/RUN position.
Page 155 GETTING TO KNOW YOUR INSTRUMENT PANEL 153 Electronic Stability Control (ESC) OFF Indicator Light — If Equipped Yellow Telltale What It Means Light Electronic Stability Control (ESC) OFF Indicator Light — If Equipped This light indicates the Electronic Stability Control (ESC) is off. Tire Pressure Monitoring System (TPMS) Warning Light Yellow Telltale...
Page 156 154 GETTING TO KNOW YOUR INSTRUMENT PANEL IMPORTANT: Do not continue driving with one or more Please note that the TPMS is not a substitute for proper tire flat tires as handling may be compromised. Stop the maintenance, and it is the driver’s responsibility to main- vehicle, avoiding sharp braking and steering.
Page 157 GETTING TO KNOW YOUR INSTRUMENT PANEL 155 CAUTION! CAUTION! (Continued) Aftermarket wheels can cause sensor damage. Using The TPMS has been optimized for the original equip- aftermarket tire sealants may cause the Tire Pressure ment tires and wheels. TPMS pressures and warning Monitoring System (TPMS) sensor to become inoper- have been established for the tire size equipped on able.
Page 158 156 GETTING TO KNOW YOUR INSTRUMENT PANEL Low Fuel Warning Light Yellow Telltale What It Means Light Low Fuel Indicator Light When the fuel level reaches approximately 2.4 gal (9.1 L) this light will turn on, and remain on until fuel is added. Forward Collision Warning Off Warning (FCW) Light Yellow Telltale...
Page 159 GETTING TO KNOW YOUR INSTRUMENT PANEL 157 Service Forward Collision Warning (FCW) Light — If Equipped Yellow Telltale What It Means Light Service Forward Collision Warning Indicator Light This light indicates a potential system fault with the FCW system. Refer to “Adaptive Cruise Control (ACC) —...
Page 160 158 GETTING TO KNOW YOUR INSTRUMENT PANEL Service Adaptive Cruise Control (ACC) System Indicator Light Yellow Telltale What It Means Light Service Adaptive Cruise Control Indicator Light This light will turn on when a ACC is not operating and needs service. For further information, refer to “Adaptive Cruise Control (ACC) —...
Page 161 GETTING TO KNOW YOUR INSTRUMENT PANEL 159 LaneSense Failure Indicator Light — If Equipped Yellow Telltale What It Means Light LaneSense Failure Indicator Light This light will turn on when the LaneSense system is not operating and needs service. Please see your authorized dealer.
Page 162: Blue Telltale Lights
160 GETTING TO KNOW YOUR INSTRUMENT PANEL Blue Telltale Lights High Beam Indicator Light Blue Telltale What It Means Light High Beam Indicator Light This indicator shows that the high beam headlights are on. Push the multifunction control lever away from you to switch the headlights to high beam. Pull the lever toward you to switch the headlights back to low beam.
Page 163 GETTING TO KNOW YOUR INSTRUMENT PANEL 161 Front Fog Indicator Light — If Equipped Green Telltale What It Means Light Front Fog Indicator Light This indicator will illuminate when the front fog lights are on. Turn Signal Warning Lights Green Tell- What It Means tale Light Turn Signal Indicator Lights...
Page 164 162 GETTING TO KNOW YOUR INSTRUMENT PANEL Cruise Control Set Indicator Light Green Telltale What It Means Light Cruise Control Set Indicator Light This light will turn on when the electronic speed control is SET. Refer to “Electronic Speed Con- trol —...
Page 165 GETTING TO KNOW YOUR INSTRUMENT PANEL 163 Adaptive Cruise Control (ACC) Set With Target Detected Light — If Equipped Green Telltale What It Means Light Adaptive Cruise Control (ACC) Set With Target Detected Light — If Equipped This light will turn on when the Adaptive Cruise Control is SET and the target vehicle is de- tected.
Page 166 164 GETTING TO KNOW YOUR INSTRUMENT PANEL Track Mode SRT Indicator Light Green Telltale What It Means Light Track Mode SRT Indicator Light This light will turn on when Track Mode SRT is active. Refer to “Selec-Track” in “Starting And Operating”...
Page 167: White Telltale Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL 165 LaneSense Indicator Light — If Equipped Green Telltale What It Means Light LaneSense Indicator Light The LaneSense indicator is solid green when both lane markings have been detected and the sys- tem is “armed” to provide visual warnings in the instrument cluster display and a torque warn- ing in the steering wheel if an unintentional lane departure occurs.
Page 168 166 GETTING TO KNOW YOUR INSTRUMENT PANEL Adaptive Cruise Control (ACC) Ready Light — If Equipped White Telltale What It Means Light Adaptive Cruise Control (ACC) Ready Light — If Equipped This light will turn on when the vehicle equipped with Adaptive Cruise Control (ACC) has been turned on and in the READY state.
Page 169: Onboard Diagnostic System - Obd Ii
GETTING TO KNOW YOUR INSTRUMENT PANEL 167 LaneSense Indicator Light — If Equipped White Telltale What It Means Light LaneSense Indicator Light When the LaneSense system is ON, the LaneSense indicator is solid white when none or only the left or right lane marking has been detected. The indicator will turn green when both lanes are detected and the system will be ready to provide visual warnings in the instrument cluster dis- play if an unintentional lane departure occurs.
Page 170: Onboard Diagnostic System (Obd Ii) Cybersecurity
168 GETTING TO KNOW YOUR INSTRUMENT PANEL Onboard Diagnostic System (OBD II) Cybersecurity For further information, refer to “Privacy Practices” and “Uconnect CyberSecurity” in “All About Uconnect Access” Your vehicle is required to have an Onboard Diagnostic in your Owner’s Manual Radio Supplement and “Cyber- system (OBD II) and a connection port to allow access to security”...
Page 171 GETTING TO KNOW YOUR INSTRUMENT PANEL 169 • The MIL will not flash at all and will remain fully Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station. To check if illuminated until you place the ignition in the off posi- your vehicle’s OBD II system is ready, you must do the tion or start the engine.
Page 173 SAFETY CONTENTS ▫ Seat Belt Systems ..... .207 SAFETY FEATURES ..... .172 ▫...
Page 174: Safety Features
172 SAFETY SAFETY FEATURES These are all normal characteristics of ABS. Anti-Lock Brake System (ABS) WARNING! The Anti-Lock Brake System (ABS) provides increased • The ABS contains sophisticated electronic equip- vehicle stability and brake performance under most brak- ment that may be susceptible to interference caused ing conditions.
Page 175: Electronic Brake Control System
SAFETY benefits of anti-lock brakes. If the “Anti-Lock Brake Warn- WARNING! (Continued) ing Light” does not come on when the ignition is turned to • The capabilities of an ABS equipped vehicle must the ON/RUN mode, have the light repaired as soon as never be exploited in a reckless or dangerous manner possible.
Page 176 174 SAFETY Brake System Warning Light longer desired. Once the brake pedal is released, the BAS is deactivated. The red “Brake System Warning Light” will turn on when the ignition is turned to the ON/RUN mode and may stay WARNING! on for as long as four seconds.
Page 177 SAFETY The following conditions must be met in order for HSA to WARNING! (Continued) activate: while pulling a trailer. HSA is not a substitute for • The feature must be enabled. active driving involvement. It is always the driver’s responsibility to be attentive to distance to other ve- •...
Page 178 176 SAFETY For vehicles not equipped with an instrument cluster Towing With HSA display, perform the following steps: HSA will also provide assistance to mitigate roll back while towing a trailer. 1. Center the steering wheel (front wheels pointing straight forward). WARNING! 2.
Page 179 SAFETY • Oversteer - when the vehicle is turning more than reduce engine power to provide enhanced acceleration and stability. A feature of the TCS, Brake Limited Differential appropriate for the steering wheel position. (BLD), functions similar to a limited slip differential and •...
Page 180 178 SAFETY ESC On WARNING! (Continued) This is the normal operating mode for the ESC. Whenever from loss of vehicle control due to inappropriate the vehicle is started, the ESC system will be in this mode. driver input for the conditions. Only a safe, attentive, This mode should be used for most driving conditions.
Page 181 SAFETY NOTE: NOTE: System may switch from ESC “Full Off” to “Partial Off” mode when vehicle exceeds a predetermined speed. • When in “Partial Off” mode, the TCS functionality of When the vehicle speed slows below the predetermined ESC, (except for the limited slip feature described in the speed the system will return to ESC “Full Off”.
Page 182 180 SAFETY been detected in the ESC system. If this light remains on WARNING! (Continued) after several ignition cycles, and the vehicle has been engage to assist in maintaining stability. ESC “Full driven several miles (kilometers) at speeds greater than Off”...
Page 183 SAFETY • The ESC system will make buzzing or clicking sounds NOTE: ERM is disabled anytime the ESC is in “Full Off” when it is active. This is normal; the sounds will stop mode (if equipped). Refer to “Electronic Stability Control when ESC becomes inactive following the maneuver (ESC)”...
Page 184 182 SAFETY Towing” in “Starting And Operating” for further informa- in LO or HI speed. When Rain Brake Support is active, tion. When TSC is functioning, the “ESC Activation/ there is no notification to the driver and no driver interac- Malfunction Indicator Light”...
Page 185 SAFETY Hill Descent Control (HDC) — If Equipped Activating HDC HDC is intended for low speed off road driving while in Once HDC is enabled it will activate automatically if 4WD Low Range. HDC maintains vehicle speed while driven down a grade of sufficient magnitude. The set speed descending hills during various driving situations.
Page 186 184 SAFETY • 8th = 5.0 mph (8 km/h) Disabling HDC • 9th = 5.6 mph (9 km/h) – If Equipped HDC will be deactivated and disabled if any of the following conditions occur: NOTE: During HDC the +/- shifter input is used for HDC •...
Page 187 SAFETY • The cluster icon and switch lamp will flash for several 2. Enabled (feature is enabled and ready but activation seconds then extinguish when the driver pushes the conditions are not met, or driver is actively overriding HDC switch but enable conditions are not met. with brake or throttle application).
Page 188 186 SAFETY • Vehicle speed is below 20 mph (32 km/h). • PARK = SSC remains enabled but not active The set speed for SSC is selectable by the driver, and can be NOTE: adjusted by using the gear shift +/-. Additionally, the SSC •...
Page 189: Auxiliary Driving Systems
SAFETY • Vehicle is shifted to PARK. • The cluster icon and switch lamp will flash for several seconds then extinguish when the driver pushes the SSC Disabling SSC switch but enable conditions are not met. SSC will deactivate and be disabled if any of the following •...
Page 190 188 SAFETY both sides of the vehicle when the vehicle speed reaches approximately 6 mph (10 km/h) or higher and will alert the driver of vehicles in these areas. NOTE: • The BSM system DOES NOT alert the driver about rapidly approaching vehicles that are outside the detec- tion zones.
Page 191 SAFETY Sensor Location Warning Light Location The BSM system notifies the driver of objects in the The BSM system monitors the detection zone from three detection zones by illuminating the BSM warning light different entry points (side, rear, front) while driving to see located in the outside mirrors in addition to sounding an if an alert is necessary.
Page 192 190 SAFETY Entering From The Side Entering From The Rear Vehicles that move into your adjacent lanes from either Vehicles that come up from behind your vehicle on either side of the vehicle. side and enter the rear detection zone with a relative speed of less than 30 mph (48 km/h).
Page 193 SAFETY Overtaking Traffic If you pass another vehicle slowly with a relative speed less than 15 mph (24 km/h) and the vehicle remains in the blind spot for approximately 1.5 seconds, the warning light will be illuminated. If the difference in speed between the two vehicles is greater than 15 mph (24 km/h), the warning light will not illuminate.
Page 194 192 SAFETY Stationary Objects Opposing Traffic The BSM system will not alert you of objects that are WARNING! traveling in the opposite direction of the vehicle in adjacent lanes. The Blind Spot Monitoring system is only an aid to help detect objects in the blind spot zones. The BSM system is not designed to detect pedestrians, bicyclists, or animals.
Page 195 SAFETY Rear Cross Path (RCP) (5 km/h), to objects moving a maximum of approximately 20 mph (32 km/h), such as in parking lot situations. The Rear Cross Path (RCP) feature is intended to aid the driver when backing out of parking spaces where their NOTE: In a parking lot situation, oncoming vehicles can be vision of oncoming vehicles may be blocked.
Page 196 194 SAFETY Modes Of Operation NOTE: Whenever an audible alert is requested by the BSM system, the radio is also muted. Three selectable modes of operation are available in the Uconnect System. Refer to “Uconnect Settings” in “Multi- When the system is in RCP, the system shall respond with media”...
Page 197: Forward Collision Warning (Fcw) With Mitigation
SAFETY Operation is subject to the following two conditions: NOTE: FCW monitors the information from the forward looking sensors as well as the Electronic Brake Controller 1. The device may not cause harmful interference. (EBC), to calculate the probability of a forward collision. 2.
Page 198 196 SAFETY • It is unsafe to test the FCW system. To prevent such misuse of the system, after four Active Braking events within an ignition cycle, the Active Braking portion of FCW will be deactivated until the next ignition cycle. •...
Page 199 SAFETY The forward collision button is located in the Uconnect Changing the FCW status to “Far” setting allows the display in the controls settings. system to warn the driver of a possible collision with the vehicle in front using audible/visual warning when the To turn the FCW system OFF, press the forward collision latter is at a farther distance than Medium setting.
Page 200: Tire Pressure Monitor System (Tpms)
198 SAFETY of the vehicle, stationary objects that are far away, Tire Pressure Monitor System (TPMS) oncoming traffic, or leading vehicles with the same or NOTE: For vehicles equipped with run flat tires — When higher rate of speed. the TPMS indicates a tire pressure of 14 psi (96 kPa) or •...
Page 201 SAFETY tires. The tire pressure will also increase as the vehicle is For example, your vehicle has a recommended cold driven - this is normal and there should be no adjustment (parked for more than three hours) tire pressure of 33 psi for this increased pressure.
Page 202 200 SAFETY • Driving on a significantly under-inflated tire causes the CAUTION! (Continued) tire to overheat and can lead to tire failure. Under- cause the Tire Pressure Monitoring System (TPMS) inflation also reduces fuel efficiency and tire tread life, sensor to become inoperable. After using an after- and may affect the vehicle’s handling and stopping market tire sealant it is recommended that you take ability.
Page 203 SAFETY • Various Tire Pressure Monitoring System Messages, which display in the Instrument Cluster Display, and a graphic displaying tire pressures • Tire Pressure Monitoring Telltale Light Tire Pressure Monitoring Low Pressure Warnings The Tire Pressure Monitoring Telltale Light will illuminate in the instrument cluster, and an audible chime will be activated, when one or more of the four active road tire pressures are low.
Page 204 202 SAFETY once the updated tire pressure(s) have been received. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) to receive this information. SERVICE TPM SYSTEM Warning The Tire Pressure Monitoring Telltale Light will flash on and off for 75 seconds, and remain on solid when a system fault is detected.
Page 205 SAFETY 2. Installing some form of aftermarket window tinting that Display will display a “SERVICE TPM SYSTEM mes- affects radio wave signals. sage for a minimum of five seconds and then display dashes (- -) in place of the pressure value. For each 3.
Page 206 204 SAFETY The instrument cluster display will display a “SERVICE NOTE: There is no tire pressure monitoring sensor in the TPM SYSTEM” message for a minimum of five seconds. spare tire. The TPMS will not be able to monitor the tire This message is then followed by a graphic display, pressure.
Page 207 SAFETY In addition, the Tire Pressure Monitoring Telltale Light will Beginning with the next ignition cycle, the TPMS will no turn OFF and the graphic in the instrument cluster display longer chime or display the “SERVICE TPM SYSTEM” will display a new pressure value instead of dashes (- -), as message in the instrument cluster but dashes (--) will long as no tire pressure is below the low-pressure warning remain in place of the pressure values.
Page 208: Occupant Restraint Systems
206 SAFETY NOTE: Changes or modifications not expressly approved Here are some simple steps you can take to minimize the by the party responsible for compliance could void the risk of harm from a deploying air bag: user’s authority to operate the equipment. 1.
Page 209: Seat Belt Systems
SAFETY 7. The driver and front passenger seats should be moved Seat Belt Systems back as far as practical to allow the front air bags room Buckle up even though you are an excellent driver, even on to inflate. short trips. Someone on the road may be a poor driver and could cause a collision that includes you.
Page 210 208 SAFETY a few seconds. If the driver or outboard front seat passen- Change Of Status ger (if equipped with outboard front passenger seat If the driver or outboard front seat passenger (if equipped BeltAlert) is unbuckled when the ignition switch is first in with outboard front passenger seat BeltAlert) unbuckles the START or ON/RUN position the Seat Belt Reminder their seat belt while the vehicle is traveling, the BeltAlert...
Page 211 SAFETY Lap/Shoulder Belts WARNING! (Continued) All seating positions in your vehicle are equipped with • It is dangerous to ride in a cargo area, inside or lap/shoulder belts. outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or The seat belt webbing retractor will lock only during very killed.
Page 212 210 SAFETY WARNING! (Continued) WARNING! (Continued) • A lap belt worn too high can increase the risk of vehicle in a collision, increasing head and neck injury in a collision. The seat belt forces won’t be at injury. A seat belt worn under the arm can cause the strong hip and pelvic bones, but across your internal injuries.
Page 213 SAFETY equipped with a rear seat). Grasp the latch plate and 3. When the seat belt is long enough to fit, insert the latch pull out the seat belt. Slide the latch plate up the plate into the buckle until you hear a “click.” webbing as far as necessary to allow the seat belt to go around your lap.
Page 214 212 SAFETY 4. Position the lap belt so that it is snug and lies low across 6. To release the seat belt, push the red button on the your hips, below your abdomen. To remove slack in the buckle. The seat belt will automatically retract to its lap belt portion, pull up on the shoulder belt.
Page 215 SAFETY Adjustable Upper Shoulder Belt Anchorage NOTE: The adjustable upper shoulder belt anchorage is equipped with an Easy Up feature. This feature allows the In the driver and front passenger seats, the top of the shoulder belt anchorage to be adjusted in the upward shoulder belt can be adjusted upward or downward to position without pushing or squeezing the release button.
Page 216 214 SAFETY position, your authorized dealer can provide you with a Seat Belts And Pregnant Women Seat Belt Extender. The Seat Belt Extender should be used only if the existing seat belt is not long enough. When the Seat Belt Extender is not required for a different occupant, it must be removed.
Page 217 SAFETY Seat Belt Pretensioner Switchable Automatic Locking Retractor (ALR) The front seat belt system is equipped with pretensioning The seat belts in the passenger seating positions are devices that are designed to remove slack from the seat belt equipped with a Switchable Automatic Locking Retractor in the event of a collision.
Page 218 216 SAFETY ALR is activated, you will hear a clicking sound as the seat How To Engage The Automatic Locking Mode belt retracts. Allow the webbing to retract completely in 1. Buckle the combination lap and shoulder belt. this case and then carefully pull out only the amount of 2.
Page 219 SAFETY How The Active Head Restraints (AHR) Work WARNING! (Continued) The Occupant Restraint Controller (ORC) determines • Do not use the Automatic Locking Mode to restrain whether the severity or type of rear impact will require the occupants who are wearing the seat belt or children Active Head Restraints (AHR) to deploy.
Page 220 218 SAFETY Active Head Restraint (AHR) Components: WARNING! (Continued) restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a collision. • Do not place items over the top of the Active Head Restraint, such as coats, seat covers or portable DVD players.
Page 221: Supplemental Restraint Systems (Srs)
SAFETY forward and separated from the rear half of the head The air bag system must be ready to protect you in a restraint (see image). Do not drive your vehicle after the collision. The Occupant Restraint Controller (ORC) moni- AHRs have deployed.
Page 222 220 SAFETY Air Bag Warning Light The ORC also includes diagnostics that will illuminate the instrument panel Air Bag Warning Light if a malfunction is The ORC monitors the readiness of the electronic detected that could affect the air bag system. The diagnos- parts of the air bag system whenever the ignition tics also record the nature of the malfunction.
Page 223 SAFETY panel. The Redundant Air Bag Warning Light will stay on WARNING! until the fault is cleared. In addition, a single chime will sound to alert you that the Redundant Air Bag Warning Ignoring the Air Bag Warning Light in your instrument Light has come on and a fault has been detected.
Page 224 222 SAFETY Front Air Bags This vehicle has front air bags and lap/shoulder belts for both the driver and front passenger. The front air bags are a supplement to the seat belt restraint systems. The driver front air bag is mounted in the center of the steering wheel. The passenger front air bag is mounted in the instrument panel, above the glove compartment.
Page 225 SAFETY driver or front passenger seat belt is buckled. The seat belt WARNING! (Continued) buckle switch may adjust the inflation rate of the Ad- • Never place a rear-facing child restraint in front of an vanced Front Air Bags. air bag. A deploying passenger front air bag can This vehicle may be equipped with driver and/or front cause death or serious injury to a child 12 years or passenger seat track position sensors that may adjust the...
Page 226 224 SAFETY When the ORC detects a collision requiring the front air WARNING! (Continued) bags, it signals the inflator units. A large quantity of collisions, air bags won’t deploy at all. Always wear non-toxic gas is generated to inflate the front air bags. your seat belts even though you have air bags.
Page 227 SAFETY Supplemental Driver Knee Air Bag This vehicle is equipped with a Supplemental Driver Knee Air Bag mounted in the instrument panel below the steering column. The Supplemental Driver Knee Air Bag provides enhanced protection during a frontal impact by working together with the seat belts, pretensioners, and front air bags.
Page 228 226 SAFETY area where the SAB inflates. Children are at an even greater risk of injury from a deploying air bag. WARNING! Do not use accessory seat covers or place objects between you and the Side Air Bags; the performance could be adversely affected and/or objects could be pushed into you, causing serious injury.
Page 229 SAFETY area where the SABICs inflate. Children are at an even Side Air Bags are a supplement to the seat belt restraint greater risk of injury from a deploying air bag. system. Side Air Bags deploy in less time than it takes to blink your eyes.
Page 230 228 SAFETY The Side Air Bags will not deploy in all side collisions, WARNING! (Continued) including some collisions at certain angles, or some side • Being too close to the Side Air Bags during deploy- collisions that do not impact the area of the passenger ment could cause you to be severely injured or compartment.
Page 231 SAFETY The Occupant Restraint Controller (ORC) monitors the NOTE: Front and/or side air bags will not deploy in all internal circuits and interconnecting wiring associated collisions. This does not mean something is wrong with the with electrical Air Bag System Components listed below: air bag system.
Page 232 230 SAFETY • Cut off fuel to the engine. Do not drive your vehicle after the air bags have deployed. If you are involved in another collision, the air bags will • Flash hazard lights as long as the battery has power or not be in place to protect you.
Page 233 SAFETY Maintaining Your Air Bag System WARNING! (Continued) dealer. Only manufacturer approved seat accessories WARNING! may be used. If it is necessary to modify the air bag • Modifications to any part of the air bag system could system for persons with disabilities, contact your cause it to fail when you need it.
Page 234: Child Restraints
232 SAFETY • These data can help provide a better understanding of Children 12 years or younger should ride properly buckled the circumstances in which crashes and injuries occur. up in a rear seat, if available. According to crash statistics, children are safer when properly restrained in the rear NOTE: EDR data are recorded by your vehicle only if a seats rather than in the front.
Page 235 SAFETY Before buying any restraint system, make sure that it has a NOTE: label certifying that it meets all applicable Safety Stan- • For additional information, refer to www.safercar.gov/ dards. You should also make sure that you can install it in parents/index.htm or call 1–888–327–4236.
Page 236 234 SAFETY Recommended Type Of Child Child Size, Height, Weight Or Age Restraint Larger Children Children who have out-grown their Belt Positioning Booster Seat and the forward-facing child restraint, but vehicle seat belt, seated in the rear are too small to properly fit the seat of the vehicle vehicle’s seat belt Children Too Large for Child...
Page 237 SAFETY Older Children And Child Restraints WARNING! Children who are two years old or who have outgrown • Improper installation can lead to failure of an infant their rear-facing convertible child seat can ride forward- or child restraint. It could come loose in a collision. facing in the vehicle.
Page 238 236 SAFETY Children Too Large For Booster Seats If the answer to any of these questions was “no,” then the child still needs to use a booster seat in this vehicle. If the Children who are large enough to wear the shoulder belt child is using the lap/shoulder belt, check seat belt fit comfortably, and whose legs are long enough to bend over periodically and make sure the seat belt buckle is latched.
Page 239 SAFETY Recommendations For Attaching Child Restraints Restraint Type Combined Use any attachment method shown with an “X” Below Weight of the LATCH – Lower Seat Belt Only LATCH – Lower Seat Belt + Top Child + Child Anchors Only Anchors + Top Tether Anchor Restraint Tether Anchor...
Page 240 238 SAFETY Lower Anchors And Tethers For CHildren (LATCH) used with the top tether anchorage to install the child Restraint System restraint. Please see the following table for more information. LATCH Positions For Installing Child Restraints In This Vehicle LATCH Label Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren.
Page 241 SAFETY Frequently Asked Questions About Installing Child Restraints With LATCH What is the weight limit (child’s weight + 65 lbs (29.5 kg) Use the LATCH anchorage system until the com- weight of the child restraint) for using the bined weight of the child and the child restraint LATCH anchorage system to attach the child is 65 lbs (29.5 kg).
Page 242 240 SAFETY Locating LATCH Anchorages Locating Tether Anchorages The lower anchorages are round bars that are There are tether strap anchorages behind each found at the rear of the seat cushion where it rear seating position located on the back of the meets the seatback, below the anchorage sym- seat.
Page 243 SAFETY Center Seat LATCH WARNING! • Do not install a child restraint in the center position using the LATCH system. This position is not ap- proved for installing child seats using the LATCH attachments. You must use the seat belt and tether anchor to install a child seat in the center seating position.
Page 244 242 SAFETY Center Seat Position Arm Rest Tether Center Seat Position Arm Rest Tether Attached 2. Pull down on the tether to unhook it from the plastic Always follow the directions of the child restraint manu- seat backing. facturer when installing your child restraint. Not all child restraint systems will be installed as described here.
Page 245 SAFETY To Install A LATCH-Compatible Child Restraint 3. Attach the lower hooks or connectors of the child restraint to the lower anchorages in the selected seating If the selected seating position has a Switchable Automatic position. Locking Retractor (ALR) seat belt, stow the seat belt, following the instructions below.
Page 246 244 SAFETY How To Stow An Unused Switchable-ALR (ALR) WARNING! (Continued) Seat Belt • Child restraint anchorages are designed to withstand When using the LATCH attaching system to install a child only those loads imposed by correctly-fitted child restraint, stow all ALR seat belts that are not being used by restraints.
Page 247 SAFETY necessary to use a locking clip. The ALR retractor can be Lap/Shoulder Belt Systems For Installing Child “switched” into a locked mode by pulling all of the Restraints In This Vehicle webbing out of the retractor and then letting the webbing retract back into the retractor.
Page 248 246 SAFETY Frequently Asked Questions About Installing Child Restraints With Seat Belts What is the weight limit (child’s Weight limit of the Child Restraint Always use the tether anchor when weight + weight of the child re- using the seat belt to install a for- straint) for using the Tether Anchor ward facing child restraint, up to the with the seat belt to attach a forward...
Page 249 SAFETY 1. Place the child seat in the center of the seating position. 6. Try to pull the webbing out of the retractor. If it is For some second row seats, you may need to recline the locked, you should not be able to pull out any webbing. seat and/or raise the head restraint to get a better fit.
Page 250 248 SAFETY Installing Child Restraints Using the Top Tether tether anchorage for that seating position, move the Anchorage child restraint to another position in the vehicle if one is available. WARNING! 2. To access the top tether strap anchorages behind the rear seat, pull the carpeted floor panel away from the seat Do not attach a tether strap for a rear-facing car seat to back, this will expose the top tether strap anchorages.
Page 251 SAFETY 5. Attach the tether strap hook of the child restraint to the top tether anchorage as shown in the diagram. Top Tether Strap Anchorage (Located on Seatback) 3. Route the tether strap to provide the most direct path for the strap between the anchor and the child seat.
Page 252: Transporting Pets
250 SAFETY WARNING! (Continued) WARNING! • An incorrectly anchored tether strap could lead to • Do not leave children or animals inside parked increased head motion and possible injury to the vehicles in hot weather. Interior heat build-up may child. Use only the anchorage position directly be- cause serious injury or death.
Page 253: Safety Checks You Should Make Inside The Vehicle
SAFETY the passenger compartment. In addition, inspect the ex- WARNING! (Continued) haust system each time the vehicle is raised for lubrication • Do not run the engine in a closed garage or in or oil change. Replace as required. confined areas any longer than needed to move your Safety Checks You Should Make Inside The Vehicle vehicle in or out of the area.
Page 254 252 SAFETY driving, have an authorized dealer service the vehicle WARNING! (Continued) immediately. Refer to “Occupant Restraint Systems” in your floor mat to interfere with the accelerator, brake, “Safety” for further information. or clutch pedals and cause a loss of vehicle control. To Defroster prevent SERIOUS INJURY or DEATH: •...
Page 255: Periodic Safety Checks You Should Make Outside
SAFETY WARNING! (Continued) WARNING! (Continued) • It is recommended to only use mild soap and water pedal (if present) to check for interference. If your floor mat interferes with the operation of any pedal, to clean your floor mats. After cleaning, always check or is not secure to the floor, remove the floor mat your floor mat has been properly installed and is from the vehicle and place the floor mat in your...
Page 256 254 SAFETY Door Latches Check for proper closing, latching, and locking. Fluid Leaks Check area under vehicle after overnight parking for fuel, engine coolant, oil, or other fluid leaks. Also, if gasoline fumes are detected or if fuel, power steering fluid (if equipped), or brake fluid leaks are suspected.
Page 257 STARTING AND OPERATING CONTENTS ▫ Eight–Speed Automatic Transmission ..265 STARTING PROCEDURES — GASOLINE ENGINES ......258 ▫...
Page 258 256 STARTING AND OPERATING ▫ Normal (Fixed Speed) Cruise Control Mode ..300 ADAPTIVE CRUISE CONTROL (ACC) — IF EQUIPPED ......283 PARKSENSE REAR PARK ASSIST —...
Page 259 STARTING AND OPERATING 257 ▫ ParkSense System Usage Precautions ..321 VEHICLE LOADING .....353 ▫...
Page 260: Starting Procedures - Gasoline Engines
258 STARTING AND OPERATING STARTING PROCEDURES — GASOLINE ENGINES WARNING! (Continued) Before starting your vehicle, adjust your seat, adjust the operate power windows, other controls, or move the inside and outside mirrors, fasten your seat belt, and if vehicle. present, instruct all other occupants to buckle their seat •...
Page 261: Cold Weather Operation (Below -22°F Or −30°C)
STARTING AND OPERATING 259 To Turn Off The Engine Using ENGINE START/STOP ENGINE START/STOP Button Functions — With Driv- Button er’s Foot OFF The Brake Pedal (In PARK Or NEUTRAL Position) 1. Place the gear selector in PARK, then push and release The ENGINE START/STOP button operates similar to an the ENGINE START/STOP button.
Page 262: After Starting
260 STARTING AND OPERATING After Starting After Starting The idle speed is controlled automatically, and it will The idle speed is controlled automatically, and it will decrease as the engine warms up. decrease as the engine warms up. If Engine Fails To Start ENGINE BREAK-IN RECOMMENDATIONS —...
Page 263: Parking Brake
STARTING AND OPERATING 261 • Drive with the engine speed less than 3,500 RPM. For the first 1500 miles (2414 km): • Maintain vehicle speed below 55 mph (88 km/h) and • Do not participate in track events, sport driving schools, observe local speed limits.
Page 264 262 STARTING AND OPERATING When parking on a hill, it is important to turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. Apply the parking brake before placing the gear selector in PARK, otherwise the load on the transmission locking mechanism may make it difficult to move the gear selector out of PARK.
Page 265: Automatic Transmission
STARTING AND OPERATING 263 WARNING! (Continued) CAUTION! (Continued) • When leaving the vehicle, always make sure the indicated. Have the brake system serviced by an au- keyless ignition node is in the “OFF” mode, remove thorized dealer immediately. the key fob from the vehicle and lock the vehicle. •...
Page 266: Ignition Park Interlock
264 STARTING AND OPERATING WARNING! (Continued) CAUTION! (Continued) • When leaving the vehicle, always make sure the • Do not shift between PARK, REVERSE, NEUTRAL, ignition is in the OFF mode, remove the key fob from or DRIVE when the engine is above idle speed. •...
Page 267: Fuel Economy (Eco) Mode
STARTING AND OPERATING 265 also be pressed to shift from NEUTRAL into DRIVE or When the Fuel Economy (ECO) Mode is engaged, the REVERSE when the vehicle is stopped or moving at low vehicle control systems will change the following: speeds.
Page 268 266 STARTING AND OPERATING DRIVE or REVERSE when the vehicle is stopped or mov- NOTE: If the gear selector cannot be moved to the PARK, ing at low speeds (refer to “Brake/Transmission Shift REVERSE, or NEUTRAL position (when pushed forward) Interlock System”...
Page 269 STARTING AND OPERATING 267 NOTE: After selecting any gear range, wait a moment to WARNING! allow the selected gear to engage before accelerating. This • Never use the PARK position as a substitute for the is especially important when the engine is cold. parking brake.
Page 270 268 STARTING AND OPERATING WARNING! (Continued) CAUTION! turn the ignition OFF. When the ignition is in the • Before moving the transmission gear selector out of OFF mode, the transmission is locked in PARK, PARK, you must start the engine, and also press the securing the vehicle against unwanted movement.
Page 271 STARTING AND OPERATING 269 NOTE: If the gear selector cannot be moved to the PARK, WARNING! (Continued) REVERSE, or NEUTRAL position (when pushed forward) conditions. You might lose control of the vehicle and it is probably in the AutoStick (+/-) position (beside the have a collision.
Page 272 270 STARTING AND OPERATING Wheel Drive Operation” in “Starting And Operating”) or result in transmission damage, Transmission Limp Home use the AutoStick shift control (refer to “AutoStick” in this Mode is activated. In this mode, the transmission may section for further information) to select a lower gear. operate only in certain gears, or may not shift at all.
Page 273: Autostick
STARTING AND OPERATING 271 4. Wait approximately 30 seconds. Autostick AutoStick is a driver-interactive transmission feature pro- 5. Restart the engine. viding manual shift control, giving you more control of the 6. Shift into the desired gear range. If the problem is no vehicle.
Page 274 272 STARTING AND OPERATING • If a requested downshift would cause the engine to the transmission to the next lower gear. Tapping the selector rearward (+) (or tapping the (+) shift paddle) will over-speed, that shift will not occur. command an upshift. •...
Page 275: Four-Wheel Drive Operation
STARTING AND OPERATING 273 WARNING! (Continued) and the vehicle could skid, causing a collision or personal injury. FOUR-WHEEL DRIVE OPERATION Selec-Track — If Equipped (SRT) Description Selec-Track combines the capabilities of the vehicle control systems, along with driver input, to provide the best performance for all terrains.
Page 276 274 STARTING AND OPERATING • Snow – Tuning set for additional stability in inclement Transmission, Steering, Suspension, all-wheel drive set up, weather. Use on and off road on loose traction surfaces and Paddle shifter settings may be configured through the such as snow.
Page 277 STARTING AND OPERATING 275 • Launch Control is intended to be used on dry, paved Launch Control — If Equipped road surfaces only. This vehicle is equipped with a Launch Control system that is designed to allow the driver to achieve maximum CAUTION! vehicle acceleration in a straight line.
Page 278 276 STARTING AND OPERATING 3. Press the “Activate Launch Control” button on the Launch control will abort before launch completion, dis- touchscreen, follow instructions in the instrument clus- play “Launch Aborted” in the cluster under any the ter display. following conditions: •...
Page 279 STARTING AND OPERATING 277 • It is recommended that each track outing should end Guidelines For Track Use with a minimum of 1 cool down lap using minimal NOTE: Because of the extreme conditions encountered braking. during track use, any damage or wear associated with •...
Page 280 278 STARTING AND OPERATING • Tire pressure: 3. Do not continue for more than 1 full burnishing lap after • 40psi (276kpa) hot, recommend 32psi (221kpa) front, you start smelling the brakes. Do not get them smoking heavily. This will get them too hot and affect their life 30psi (207 kpa) rear cold negatively in future track use.
Page 281: Fuel Saver Technology - If Equipped
STARTING AND OPERATING 279 capacity. Resurfacing also thins the rotor cheek, making Alternate electric power steering efforts can be selected it less robust and increasing the likelihood of pulsation through the Uconnect System. Refer to ”Customer Pro- in further track use. grammable Features”...
Page 282: Speed Control - If Equipped
280 STARTING AND OPERATING NOTE: • Even if the power steering assistance is no longer operational, it is still possible to steer the vehicle. Under these conditions there will be a substantial increase in steering effort, especially at low speeds and during parking maneuvers.
Page 283: To Activate
STARTING AND OPERATING 281 To Set A Desired Speed WARNING! Turn the Speed Control on. When the vehicle has reached Speed Control can be dangerous where the system the desired speed, push the SET (+) or SET (-) button and cannot maintain a constant speed.
Page 284: To Accelerate For Passing
282 STARTING AND OPERATING • If the button is continually pushed, the set speed will • If the button is continually pushed, the set speed will continue to increase until the button is released, then the continue to decrease until the button is released, then the new set speed will be established.
Page 285: To Deactivate
STARTING AND OPERATING 283 To Deactivate NOTE: • If the sensor does not detect a vehicle ahead of you, ACC A soft tap on the brake pedal, pushing the CANC button, or normal brake pressure while slowing the vehicle will will maintain a fixed set speed.
Page 286 284 STARTING AND OPERATING WARNING! WARNING! (Continued) • Will bring the vehicle to a complete stop while • Adaptive Cruise Control (ACC) is a convenience following a target vehicle and hold the vehicle for system. It is not a substitute for active driving approximately 3 minutes in the stop position.
Page 287: Adaptive Cruise Control (Acc) Operation
STARTING AND OPERATING 285 Adaptive Cruise Control (ACC) Operation NOTE: Any chassis/suspension or tire size modifications to the vehicle will effect the performance of the Adaptive The Speed Control buttons (located on the right side of the Cruise Control and Forward Collision Warning System. steering wheel) operates the ACC system.
Page 288: To Activate/Deactivate
286 STARTING AND OPERATING • When the brakes are overheated. system will turn off and the instrument cluster displays “Adaptive Cruise Control (ACC) Off.” • When the driver door is open. • When the driver seat belt is unbuckled. • ESC Full-Off Mode is active. To Activate/Deactivate Push and release the Adaptive Cruise Control (ACC) on/off button.
Page 289: To Set A Desired Acc Speed
STARTING AND OPERATING 287 To Set A Desired ACC Speed To Cancel When the vehicle reaches the speed desired, push the The following conditions cancel the system: SET + button or the SET - button and release. The instru- • The brake pedal is applied. ment cluster display will display the set speed.
Page 290: To Turn Off
288 STARTING AND OPERATING • ACC cannot be resumed if there is a stationary vehicle To Turn Off in-front of your vehicle in close proximity. The system will turn off and clear the set speed in memory WARNING! • The Adaptive Cruise Control (ACC) on/off button is The Resume function should only be used if traffic pushed.
Page 291 STARTING AND OPERATING 289 U.S. Speed (mph) Know Your Instrument Panel” for more information. The speed decrement shown is dependant on the chosen speed • Pushing the SET + button once will result in a 1 mph unit of U.S. (mph) or Metric (km/h): increase in set speed.
Page 292: Setting The Following Distance In Acc
290 STARTING AND OPERATING NOTE: Setting The Following Distance In ACC • When you override and push the SET + button or SET - The specified following distance for ACC can be set by varying the distance setting between four bars (longest), buttons, the new Set Speed will be the current speed of three bars (long), two bars (medium) and one bar (short).
Page 293 STARTING AND OPERATING 291 Distance Setting 3 Bars (Long) Distance Setting 2 Bars (Medium)
Page 294 292 STARTING AND OPERATING Indicator” icon, and the system adjusts vehicle speed automatically to maintain the distance setting, regardless of the set speed. The vehicle will then maintain the set distance until: • The vehicle ahead accelerates to a speed above the set speed.
Page 295: Overtake Aid
STARTING AND OPERATING 293 ACC Operation At Stop If the ACC system brings your vehicle to a standstill while following a target vehicle, if the target vehicle starts moving within two seconds of your vehicle coming to a standstill, your vehicle will resume motion without the need for any driver action.
Page 296: Adaptive Cruise Control (Acc) Menu
294 STARTING AND OPERATING Push the SET + or the SET- button (located on the steering WARNING! (Continued) wheel) and the following will display in the instrument in the path of the vehicle. Failure to follow these cluster display: warnings can result in a collision and death or serious ACC SET personal injury.
Page 297: Display Warnings And Maintenance
STARTING AND OPERATING 295 Display Warnings And Maintenance NOTE: If the “ACC/FCW Unavailable Wipe Front Radar Sensor” warning is active Normal (Fixed Speed) Cruise “Wipe Front Radar Sensor In Front Of Vehicle” Control is still available. For additional information refer to Warning “Normal (Fixed Speed) Cruise Control Mode”...
Page 298 296 STARTING AND OPERATING • Do not attach or install any accessories near the sensor, become temporarily blinded due to obstructions, such as including transparent material or aftermarket grilles. Do- mud, dirt, or ice on windshield and fog on the inside of ing so could cause an ACC system failure or malfunction.
Page 299: Precautions While Driving With Acc
STARTING AND OPERATING 297 NOTE: If the “ACC/FCW Limited Functionality Clean Offset Driving Front Windshield” message occurs frequently (e.g. more ACC may not detect a vehicle in the same lane that is offset than once on every trip) without any snow, rain, mud, or from your direct line of travel, or a vehicle merging in from other obstruction, have the windshield and forward facing a side lane.
Page 300 298 STARTING AND OPERATING Turns And Bends Using ACC On Hills When driving on a curve with ACC engaged, the system When driving on hills, ACC may not detect a vehicle in may decrease the vehicle speed and acceleration for stabil- your lane.
Page 301 STARTING AND OPERATING 299 is completely in the lane. There may not be sufficient Narrow Vehicles distance to the lane-changing vehicle. Always be attentive Some narrow vehicles traveling near the outer edges of the and ready to apply the brakes if necessary. lane or edging into the lane are not detected until they have moved fully into the lane.
Page 302: General Information
300 STARTING AND OPERATING Stationary Objects And Vehicles Operation is subject to the following two conditions: ACC does not react to stationary objects and stationary 1. The device may not cause harmful interference. vehicles. For example, ACC will not react in situations 2.
Page 303 STARTING AND OPERATING 301 To Vary The Speed Setting WARNING! To Increase Speed In the Normal (Fixed Speed) Cruise Control mode, the When the Normal (Fixed Speed) Cruise Control is set, you system will not react to vehicles ahead. In addition, the can increase speed by pushing the SET + button.
Page 304 302 STARTING AND OPERATING • If the button is continually pushed, the set speed will Metric Speed (km/h) continue to increase in 10 km/h increments until the • Pushing the SET - button once will result in a 1 km/h button is released.
Page 305: Parksense Rear Park Assist - If Equipped
STARTING AND OPERATING 303 To Resume Speed Automatic Transmission, the vehicle brakes may be auto- matically applied and released when performing a reverse To resume a previously set speed, push the RES button and parking maneuver if the system detects a possible collision release.
Page 306: Parksense Sensors
304 STARTING AND OPERATING • The automatic braking function can be enabled/ ParkSense will retain the last system state (enabled or disabled from the Customer-Programmable Features disabled) from the last ignition cycle when the ignition is section of the Uconnect System. changed to the ON/RUN position.
Page 307: Parksense Warning Display
STARTING AND OPERATING 305 ParkSense Warning Display ParkSense Display The ParkSense Warning screen will only be displayed if When the vehicle is in REVERSE and an obstacle has been Sound and Display is selected from the Customer - Pro- detected, the warning display will turn on indicating the grammable Features section of the Uconnect System.
Page 308 306 STARTING AND OPERATING If an obstacle is detected in the left and/or right rear region, the display will show a single arc in the left and/or right rear region and the system will produce a tone. As the vehicle moves closer to the obstacle, the display will show the single arc moving closer to the vehicle and the tone will change from a single 1/2 second tone to slow, to fast, to continuous.
Page 309 STARTING AND OPERATING 307 Slow Tone Fast Tone...
Page 310 308 STARTING AND OPERATING Fast Tone Continuous Tone...
Page 311 STARTING AND OPERATING 309 The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting an obstacle: WARNING ALERTS Rear Greater...
Page 312: Enabling And Disabling Parksense
310 STARTING AND OPERATING Adjustable Chime Volume Settings The ParkSense switch LED will be on when ParkSense is disabled or requires service. The ParkSense switch LED Rear chime volume settings can be selected from the will be off when the system is enabled. If the ParkSense Customer-Programmable Features section of the Uconnect switch is pushed, and the system requires service, the System, refer to “Uconnect Settings”...
Page 313: Cleaning The Parksense System
STARTING AND OPERATING 311 • When you move the gear selector to the REVERSE is clean and clear of snow, ice, mud, dirt or other obstruc- tion and then cycle the ignition. If the message continues to position and ParkSense is turned OFF, the instrument appear, see an authorized dealer.
Page 314: Parksense Front And Rear Park Assist - If Equipped
312 STARTING AND OPERATING • ParkSense should be disabled when the liftgate is in the WARNING! (Continued) open position and the vehicle is in REVERSE. An open and shape, giving a false indication that an obstacle liftgate could provide a false indication that an obstacle is behind the vehicle.
Page 315 STARTING AND OPERATING 313 • The automatic braking function can be enabled/ vehicle is equipped with an Automatic Transmission, the vehicle brakes may be automatically applied and released disabled from the Customer-Programmable Features when performing a reverse parking maneuver if the sys- section of the Uconnect System.
Page 316: Parksense Sensors
314 STARTING AND OPERATING ParkSense will retain the last system state (enabled or The six ParkSense sensors, located in the front fascia/ disabled) from the last ignition cycle when the ignition is bumper, monitor the area in front of the vehicle that is changed to the ON/RUN position.
Page 317: Parksense Display
STARTING AND OPERATING 315 ParkSense Display If an object is detected in the left and/or right rear region, the display will show a single arc in the left and/or right When the vehicle is in REVERSE and an obstacle has been rear region and the system will produce a tone.
Page 318 316 STARTING AND OPERATING Slow Tone Slow Tone For Rear Only...
Page 319 STARTING AND OPERATING 317 Fast Tone For Rear Only Fast Tone...
Page 320 318 STARTING AND OPERATING The vehicle is close to the obstacle when the instrument cluster display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert operation when the system is detecting an obstacle: Continuous Tone WARNING ALERTS FOR REAR Rear...
Page 321 STARTING AND OPERATING 319 WARNING ALERTS FOR REAR Rear Greater 79-59 inches 59-47 inches 47-39 inches 39-25 inches 25-12 inches Less than Distance than (150-100 cm) (150-120 cm) (120-100 cm) (100-65 cm) (65-30 cm) 12 inches (inches/cm) 79 inches (30 cm) (200 cm) Arcs-Center None...
Page 322: Enabling And Disabling Parksense
320 STARTING AND OPERATING NOTE: ParkSense will reduce the volume of the radio, if the “PARKSENSE OFF” message for approximately five on, when the system is sounding an audio tone. seconds. Refer to “Instrument Cluster Display” in “Getting To Know Your Instrument Panel” for further information. Front Park Assist Audible Alerts When the gear selector is moved to REVERSE and the ParkSense will turn off the Front Park Assist audible alert...
Page 323: Cleaning The Parksense System
STARTING AND OPERATING 321 faulted condition, the instrument cluster display will dis- snow, ice, mud, dirt or other obstruction and then cycle the play a PARKSENSE UNAVAILABLE WIPE REAR SEN- ignition. If the message continues to appear see an autho- SORS , PARKSENSE UNAVAILABLE WIPE FRONT SEN- rized dealer.
Page 324 322 STARTING AND OPERATING • When you move the gear selector to the REVERSE • ParkSense should be disabled when the liftgate is in the position and ParkSense is turned off, the instrument open position. An opened liftgate could provide a false cluster will display “PARKSENSE OFF”...
Page 325: Parksense Active Park Assist System - If Equipped
STARTING AND OPERATING 323 ParkSense Active Park Assist system is capable of maneu- CAUTION! vering a vehicle into a parallel or a perpendicular parking • ParkSense is only a parking aid and it is unable to space on either side (i.e., driver side or passenger side). recognize every obstacle, including small obstacles.
Page 326: Enabling And Disabling The Parksense Active Park Assist System
324 STARTING AND OPERATING to improve the performance of the feature. The system To enable the ParkSense Active Park Assist system, will also continuously perform the dynamic vehicle push the ParkSense Active Park Assist switch once (LED calibration to account for differences such as over or turns on).
Page 327: Parallel Parking Space Assistance Operation/Display
STARTING AND OPERATING 325 • The ParkSense Active Park Assist system will allow a • The outer surface and the underside of the front and rear maximum of six shifts between DRIVE and REVERSE. If fascias/bumpers are clean and clear of snow, ice, mud, the maneuver cannot be completed within six shifts, dirt or other obstruction.
Page 328 326 STARTING AND OPERATING • The driver needs to make sure that the selected parking space for the maneuver remains free and clear of any obstructions (e.g. pedestrians, bicycles, etc.). • The driver is responsible to ensure that the selected parking space is suitable for the maneuver and free/ clear of anything that may be overhanging or protruding into the parking space (e.g., ladders, tailgates, etc.
Page 329 STARTING AND OPERATING 327 Space Found — Keep Moving Forward Space Found — Stop And Remove Hands From Wheel Once the vehicle is in position, you will be instructed to Once the vehicle is at a standstill with your hands removed stop the vehicle’s movement and remove your hands from from the steering wheel, you will be instructed to place the the steering wheel.
Page 330 328 STARTING AND OPERATING Space Found — Shift To Reverse Check Surroundings — Wait For Steering To Complete When the driver places the gear selector into the REVERSE The system will then instruct the driver to check their position, the system may instruct the driver to wait for surroundings and move backward.
Page 331 STARTING AND OPERATING 329 • The ParkSense Active Park Assist system will allow a maximum of six shifts between DRIVE and REVERSE. If the maneuver cannot be completed within six shifts, the system will cancel and the instrument cluster display will instruct the driver to complete the maneuver manu- ally.
Page 332 330 STARTING AND OPERATING When the vehicle has reached the end of its backward Once the vehicle is in a standstill condition, the driver will movement, the system will instruct the driver to check be instructed to place the gear selector into the DRIVE their surroundings and stop the vehicle’s movement.
Page 333 STARTING AND OPERATING 331 When the driver places the gear selector into the DRIVE The system will then instruct the driver to check their position, the system may instruct the driver to wait for surroundings and move forward. steering to complete. Check Surroundings —...
Page 334 332 STARTING AND OPERATING When the vehicle has reached the end of its forward Once the vehicle is in a standstill condition, the driver will movement, the system will instruct the driver to check be instructed to place the gear selector into the REVERSE their surroundings and stop the vehicle’s movement.
Page 335 STARTING AND OPERATING 333 When the driver places the gear selector into the REVERSE The system will then instruct the driver to check their position, the system may instruct the driver to wait for surroundings and move backward. steering to complete. Check Surroundings —...
Page 336: Perpendicular Parking Space Assistance Operation/Display
334 STARTING AND OPERATING Your vehicle is now in the parallel park position. When the Perpendicular Parking Space Assistance maneuver is complete, the driver will be instructed to Operation/Display check the vehicle’s parking position. If the driver is satis- When the ParkSense Active Park Assist system is enabled, fied with the vehicle position, they should shift to PARK.
Page 337 STARTING AND OPERATING 335 • The driver needs to make sure that the selected parking space for the maneuver remains free and clear of any obstructions (e.g. pedestrians, bicycles, etc.). • The driver is responsible to ensure that the selected parking space is suitable for the maneuver and free/ clear of anything that may be overhanging or protruding into the parking space (e.g., ladders, tailgates, etc.
Page 338 336 STARTING AND OPERATING When an available parking space has been found, and the Once the vehicle is in position, you will be instructed to vehicle is not in position, you will be instructed to move stop the vehicle’s movement and remove your hands from forward to position the vehicle for a perpendicular parking the steering wheel.
Page 339 STARTING AND OPERATING 337 Once the vehicle is at a standstill with your hands removed When the driver places the gear selector into the REVERSE from the steering wheel, you will be instructed to place the position, the system may instruct the driver to wait for gear selector into the REVERSE position.
Page 340 338 STARTING AND OPERATING • The ParkSense Active Park Assist system will allow a The system will then instruct the driver to check their surroundings and move backward. maximum of six shifts between DRIVE and REVERSE. If the maneuver cannot be completed within six shifts, the system will cancel and the instrument cluster display will instruct the driver to complete the maneuver manually.
Page 341 STARTING AND OPERATING 339 When the vehicle has reached the end of its backward Once the vehicle is in a standstill condition, the driver will movement, the system will instruct the driver to check be instructed to place the gear selector into the DRIVE their surroundings and stop the vehicle’s movement.
Page 342 340 STARTING AND OPERATING When the driver places the gear selector into the DRIVE The system will then instruct the driver to check their position, the system may instruct the driver to wait for surroundings and move forward. steering to complete. Check Surroundings —...
Page 343 STARTING AND OPERATING 341 When the vehicle has reached the end of its forward Once the vehicle is in a standstill condition, the driver will movement, the system will instruct the driver to check be instructed to place the gear selector into the REVERSE their surroundings and stop the vehicle’s movement.
Page 344 342 STARTING AND OPERATING When the driver places the gear selector into the REVERSE The system will then instruct the driver to check their position, the system may instruct the driver to wait for surroundings and move backward. steering to complete. Check Surroundings —...
Page 345 STARTING AND OPERATING 343 WARNING! (Continued) continue to pay attention to your surroundings. Fail- ure to do so can result in serious injury or death. • Before using the ParkSense Active Park Assist sys- tem, it is strongly recommended that the ball mount and hitch ball assembly is disconnected from the vehicle when the vehicle is not used for towing.
Page 346: Lanesense - If Equipped
344 STARTING AND OPERATING the LaneSense system provides a visual warning through CAUTION! (Continued) the instrument cluster display to prompt the driver to not be detected when they are in close proximity. remain within the lane boundaries. • The vehicle must be driven slowly when using the The driver may manually override the haptic warning by ParkSense Active Park Assist system in order to be applying torque into the steering wheel at any time.
Page 347: Turning Lanesense On Or Off
STARTING AND OPERATING 345 Turning LaneSense On Or Off The default status of LaneSense is off. The LaneSense button is located on the switch panel below the Uconnect display. Lane Sense On Message To turn the LaneSense system off, push the LaneSense button once (LED turns on).
Page 348: Lanesense Warning Message
346 STARTING AND OPERATING LaneSense Warning Message been detected and the system is ready to provide visual warnings in the instrument cluster display if an unin- The LaneSense system will indicate the current lane drift tentional lane departure occurs. condition through the instrument cluster display. •...
Page 349 STARTING AND OPERATING 347 Left Lane Departure — Both Lanes Detected The LaneSense indicator changes from solid green to solid yellow. At this time torque is applied to the • When the LaneSense system is on, the lane lines turn steering wheel in the opposite direction of the lane from gray to white to indicate that both of the lane boundary.
Page 350: Changing Lanesense Status
348 STARTING AND OPERATING changes from solid yellow to flashing yellow. At this Changing LaneSense Status time torque is applied to the steering wheel in the The LaneSense system has settings to adjust the intensity of opposite direction of the lane boundary. the torque warning and the warning zone sensitivity •...
Page 351 STARTING AND OPERATING 349 the top of the screen. After five seconds this note will NOTE: The ParkView Rear Back Up Camera has program- disappear. The ParkView camera is located on the rear of mable modes of operation that may be selected through the the vehicle above the rear License plate.
Page 352 350 STARTING AND OPERATING NOTE: If snow, ice, mud, or any foreign substance builds WARNING! up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth. Do not cover the lens. Drivers must be careful when backing up even when using the ParkView Rear Back Up Camera.
Page 353: Refueling The Vehicle
STARTING AND OPERATING 351 REFUELING THE VEHICLE 1. Push the fuel filler door release switch (located under the headlamp switch). Fuel Filler Door Latch NOTE: In certain cold conditions, ice may prevent the fuel door from opening. If this occurs, lightly push on the fuel door to break the ice buildup and re-release the fuel door Fuel Filler Door Release Switch using the inside release button.
Page 354: Emergency Fuel Filler Door Release
352 STARTING AND OPERATING 6. Wait 5 seconds before removing the fuel nozzle to allow WARNING! (Continued) fuel to drain from nozzle. • Never add fuel when the engine is running. This is 7. Remove the fuel nozzle and close the fuel door. in violation of most state and federal fire regulations and may cause the “Malfunction Indicator Light”...
Page 355: Vehicle Loading
STARTING AND OPERATING 353 3. Grab popped up outboard edge with other hand to VEHICLE LOADING disengage snaps. Certification Label 4. Remove the storage bin. As required by National Highway Traffic Safety Adminis- tration regulations, your vehicle has a certification label 5.
Page 356 354 STARTING AND OPERATING Gross Axle Weight Rating (GAWR) Curb Weight The GAWR is the maximum permissible load on the front The curb weight of a vehicle is defined as the total weight and rear axles. The load must be distributed in the cargo of the vehicle with all fluids, including vehicle fuel, at full area so that the GAWR of each axle is not exceeded.
Page 357: Trailer Towing
STARTING AND OPERATING 355 Improper weight distributions can have an adverse effect Common Towing Definitions on the way your vehicle steers and handles and the way The following trailer towing related definitions will assist the brakes operate. you in understanding the following information: Gross Vehicle Weight Rating (GVWR) CAUTION! The GVWR is the total allowable weight of your vehicle.
Page 358 356 STARTING AND OPERATING rear GAWR. Refer to “Vehicle Loading/Vehicle Certifica- If equipped, the electronic Trailer Sway Control (TSC) tion Label” in “Starting And Operating” for further infor- recognizes a swaying trailer and automatically applies mation. individual wheel brakes and/or reduces engine power to attempt to eliminate the trailer sway.
Page 359: Trailer Hitch Classification
STARTING AND OPERATING 357 may be required depending on vehicle and trailer WARNING! (Continued) configuration/loading to comply with Gross Axle Weight and trailer manufacturer or a reputable Recreational Rating (GAWR) requirements. Vehicle dealer for additional information. WARNING! Trailer Hitch Classification •...
Page 360: Trailer Towing Weights (Maximum Trailer Weight Ratings) - Srt
358 STARTING AND OPERATING Trailer Towing Weights (Maximum Trailer Weight Ratings) — SRT GCWR Max. GTW Max. Trailer Tongue Engine/Transmission (Gross Combined Frontal Area (Gross Trailer Wt.) Wt. (See Note) Wt. Rating) 6.4L Automatic 12,600 lbs (5 715 kg) 55 sq ft (5.11 sq m) 7,200 lbs (3 265 kg) 720 lbs (327 kg) Refer to local laws for maximum trailer towing speeds.
Page 361 STARTING AND OPERATING 359 2. Pull the bottom of the cover outward (towards you). Hitch Receiver Cover Hitch Receiver Cover 1 — Hitch Receiver Cover 2 — Locking Retainer...
Page 362: Trailer And Tongue Weight
360 STARTING AND OPERATING 3. Lower back down to disengage the tabs located at the Trailer And Tongue Weight top of the hitch receiver cover and then pull outwards to Never exceed the maximum tongue weight stamped on remove. your bumper or trailer hitch. Hitch Receiver Cover Removal Consider the following items when computing the weight To reinstall the hitch receiver cover after towing repeat the...
Page 363: Towing Requirements
STARTING AND OPERATING 361 NOTE: Remember that everything put into or on the Maintenance” for the proper maintenance intervals. When trailer adds to the load on your vehicle. Also, additional towing a trailer, never exceed the GAWR or GCWR ratings. factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle.
Page 364 362 STARTING AND OPERATING • Proper tire inflation pressures are essential to the safe WARNING! (Continued) and satisfactory operation of your vehicle. Refer to • Vehicles with trailers should not be parked on a “Tires” in “Servicing And Maintenance” for proper tire grade.
Page 365 STARTING AND OPERATING 363 • An electronically actuated trailer brake controller is CAUTION! (Continued) required when towing a trailer with electronically actu- be of adequate capacity. Failure to do this could lead to ated brakes. When towing a trailer equipped with a accelerated brake lining wear, higher brake pedal hydraulic surge actuated brake system, an electronic effort, and longer stopping distances.
Page 366 364 STARTING AND OPERATING Four-Pin Connector Seven-Pin Connector 1 — Female Pins 4 — Park 1 — Battery 5 — Ground 2 — Male Pin 5 — Left Stop/Turn 2 — Backup Lamps 6 — Left Stop/Turn 3 — Ground 6 —...
Page 367: Towing Tips
STARTING AND OPERATING 365 Towing Tips AutoStick • When using the AutoStick shift control, select the high- Before setting out on a trip, practice turning, stopping, and backing up the trailer in an area located away from heavy est gear that allows for adequate performance and traffic.
Page 368: Recreational Towing
366 STARTING AND OPERATING Cooling System NOTE: This vehicle may be towed on a flatbed or vehicle trailer provided all four wheels are OFF the ground. To reduce potential for engine and transmission overheat- ing, take the following actions: DRIVING TIPS City Driving Driving On Slippery Surfaces When stopped for short periods, shift the transmission into...
Page 369: Driving Through Water
STARTING AND OPERATING 367 Traction Flowing/Rising Water When driving on wet or slushy roads, it is possible for a WARNING! wedge of water to build up between the tire and road surface. This is hydroplaning and may cause partial or Do not drive on or across a road or path where water is complete loss of vehicle control and stopping ability.
Page 370 368 STARTING AND OPERATING WARNING! (Continued) CAUTION! (Continued) • Driving through standing water limits your vehicle’s • Driving through standing water may cause damage braking capabilities, which increases stopping dis- to your vehicle’s drivetrain components. Always in- tances. Therefore, after driving through standing spect your vehicle’s fluids (i.e., engine oil, transmis- water, drive slowly and lightly press on the brake sion, axle, etc.) for signs of contamination (i.e., fluid...
Page 371 IN CASE OF EMERGENCY CONTENTS ▫ Jacking Instructions .....391 HAZARD WARNING FLASHERS ... .370 ▫...
Page 372: Hazard Warning Flashers
370 IN CASE OF EMERGENCY HAZARD WARNING FLASHERS ASSIST AND 9–1–1 MIRROR — IF EQUIPPED The Hazard Warning flasher switch is located on the switch bank just above the climate controls. Push the switch to turn on the Hazard Warning flasher.
Page 373 IN CASE OF EMERGENCY 371 NOTE: 9-1-1 Call • Your vehicle may be transmitting data as authorized by 1. Push the 9-1-1 Call button on the Rearview Mirror. the subscriber. NOTE: In case the 9-1-1 Call button is pushed in error, •...
Page 374 372 IN CASE OF EMERGENCY 4. You should be able to speak with the 9-1-1 operator 5. The 9-1-1 operator may attempt to contact appropriate through the vehicle audio system to determine if addi- emergency responders and provide them with impor- tional help is needed.
Page 375 IN CASE OF EMERGENCY 373 If the 9-1-1 Call system detects a malfunction, any of the WARNING! (Continued) following may occur at the time the malfunction is de- can cause the 9-1-1 Call system to fail, never add tected, and at the beginning of each ignition cycle: aftermarket equipment (e.g., two-way mobile radio, •...
Page 376 374 IN CASE OF EMERGENCY Even if the 9-1-1 Call system is fully functional, factors WARNING! beyond FCA US LLC’s control may prevent or stop the 9-1-1 Call system operation. These include, but are not ALWAYS obey traffic laws and pay attention to the limited to, the following factors: road.
Page 377: Bulb Replacement
IN CASE OF EMERGENCY 375 NOTE: Changes or modifications not expressly approved CAUTION! by the party responsible for compliance could void the user’s authority to operate the equipment. To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean.
Page 378 376 IN CASE OF EMERGENCY Exterior Bulbs Bulb Number Headlamps (Low Beam) Premium Headlamps (Low/High Beam) D3S (Serviced at Authorized Dealer) Headlamps (High Beam) 9005 Premium Park/Turn Signal Lamp LED - (Service at Authorized Dealer) Premium Daytime Running Lamp (DRL) LED - (Service at Authorized Dealer) Front Fog Lamps Front Side Marker...
Page 379: Bulb Replacement
IN CASE OF EMERGENCY 377 Bulb Replacement Halogen Headlamps — If Equipped High Intensity Discharge Headlamps (HID) — If 1. Open the hood. Equipped 2. Turn the low or high beam bulb one–quarter turn The headlamps are a type of high voltage discharge tube. counterclockwise to remove from housing.
Page 380 378 IN CASE OF EMERGENCY CAUTION! CAUTION! (Continued) • Always use the correct bulb size and type for replace- Do not touch the new bulb with your fingers. Oil ment. An incorrect bulb size or type may overheat contamination will severely shorten bulb life. If the and cause damage to the lamp, the socket or the lamp bulb comes in contact with any oily surface, clean the wiring.
Page 381 IN CASE OF EMERGENCY 379 Tail Lamp Push Pins Rear Of Tail Lamp 3. Grasp the tail lamp and pull firmly rearward to disen- 1 — Rear Stop Lamp Bulb Socket gage the lamp from the aperture panel. 2 — LED Tail Connector – Do Not Remove 3 —...
Page 382 380 IN CASE OF EMERGENCY Rear Liftgate Mounted Tail Lamp Liftgate Lower Trim 3. Continue removing the trim. Rear Liftgate Tail Lamps 4. Disconnect the two trim panel lights. 1. Raise the liftgate. 5. Tail lamps are now visible. Rotate socket(s) counter 2.
Page 383: Fuses
IN CASE OF EMERGENCY 381 Rear Of Liftgate Tail Lamp Center High-Mounted Stop Lamp Rear License Lamp 1 — Auxiliary LED Tail Connector – Do Not Remove 2 — Backup Bulb Socket The rear license lamps are LEDs. See your authorized dealer for service.
Page 384: General Information
382 IN CASE OF EMERGENCY Also, please be aware that when using power outlets for WARNING! (Continued) extended periods of time with the engine off may result in fuse of higher amp rating. Never replace a blown vehicle battery discharge. fuse with metal wires or any other material.
Page 385: Underhood Fuses
IN CASE OF EMERGENCY 383 Underhood Fuses The Power Distribution Center is located in the engine compartment near the battery. This center contains car- tridge fuses, micro fuses, relays, and circuit breakers. A description of each fuse and component may be stamped on the inside cover, otherwise the cavity number of each fuse is stamped on the inside cover that corresponds to the following chart.
Page 386 384 IN CASE OF EMERGENCY Cavity Cartridge Fuse Micro Fuse Description 30 Amp Pink – Trailer Tow Electric Brake — If Equipped 40 Amp Green – Body Controller #3/Power Locks 40 Amp Green – Blower Motor Front 40 Amp Green –...
Page 387 IN CASE OF EMERGENCY 385 Cavity Cartridge Fuse Micro Fuse Description 25 Amp Clear – Rear Blower Motor — If Equipped 30 Amp Pink – Power Inverter 115V AC — If Equipped 30 Amp Pink – Power Liftgate — If Equipped –...
Page 388 386 IN CASE OF EMERGENCY Cavity Cartridge Fuse Micro Fuse Description – 10 Amp Red Air Conditioning Clutch – 20 Amp Yellow Ignition Coils (Gas), Urea Heater (Diesel) – 25 Amp Clear Fuel Injectors/Powertrain – 10 Amp Red Sunroof/Passenger Window Switches/Rain Sensor –...
Page 389 IN CASE OF EMERGENCY 387 Cavity Cartridge Fuse Micro Fuse Description – 10 Amp Red Universal Garage Door Opener/Compass/ Anti-Intrusion Module – 20 Amp Yellow Trailer Tow Right Turn/Stop Lights – 10 Amp Red Steering Column Control Module/Cruise Control/DTV – 10 Amp Red Fuel Door –...
Page 390 388 IN CASE OF EMERGENCY Cavity Cartridge Fuse Micro Fuse Description – 20 Amp Yellow Rear Heated Seats & Heated Steering Wheel — If Equipped – 20 Amp Yellow Front Heated Seats — If Equipped – 10 Amp Red Climate Control/Driver Assistance Systems Module/DSRC F100 –...
Page 391: Jacking And Tire Changing
IN CASE OF EMERGENCY 389 JACKING AND TIRE CHANGING Run Flat Tires This vehicle is equipped with “run flat” tires. Run flat tires WARNING! allow the vehicle to be driven approximately 50 miles (80km) at 55 mph (88km/h). Tire service should be ob- •...
Page 392: Jack Location
390 IN CASE OF EMERGENCY Jack Location Spare Tire Stowage The scissor-type jack and tire changing tools are located in The spare tire is stowed under the load floor in the rear rear cargo area, below the load floor. cargo area and is secured to the body with a special wing nut.
Page 393: Jacking Instructions
IN CASE OF EMERGENCY 391 5. Turn the ignition OFF. WARNING! (Continued) 6. Block both the front and rear of the wheel diagonally • Turn on the Hazard Warning flasher. opposite of the jacking position. For ex- • Block the wheel diagonally opposite the wheel to be ample, if changing the right front tire, block raised.
Page 394 392 IN CASE OF EMERGENCY 3. Assemble the jack and jacking tools. Jack Warning Label Jack And Tool Assembly CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the Jacking Instructions for this vehicle. 1.
Page 395 IN CASE OF EMERGENCY 393 Jacking Locations Lift Point Symbol On Sill Molding 4. For the front axle, place the jack on the body flange just behind the front tire as indicated by the triangular lift point symbol on the sill molding. Do not raise the vehicle until you are sure the jack is fully engaged.
Page 396 394 IN CASE OF EMERGENCY CAUTION! Do NOT raise the vehicle by the body side sill mold- ing. Be sure the jack is placed in the proper engage- ment location on the inside of the panel. Damage of the vehicle may occur if the procedure is not properly followed.
Page 397 IN CASE OF EMERGENCY 395 8. Position the spare wheel/tire on the vehicle and install the lug nuts with the cone-shaped end toward the wheel. Lightly tighten the nuts. CAUTION! Be sure to mount the inflatable spare tire with the valve stem facing outward.
Page 398 396 IN CASE OF EMERGENCY WARNING! To avoid the risk of forcing the vehicle off the jack, do not tighten the wheel nuts fully until the vehicle has been lowered. Failure to follow this warning may result in serious injury. 9.
Page 399: Road Tire Installation
IN CASE OF EMERGENCY 397 5. After 25 miles (40 km) check the lug nut torque with a WARNING! torque wrench to ensure that all lug nuts are properly seated against the wheel. A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle.
Page 400: Preparations For Jump-Start
398 IN CASE OF EMERGENCY Preparations For Jump-Start WARNING! The battery in your vehicle is located under the passenger’s • Take care to avoid the radiator cooling fan whenever front seat. There are remote locations located under the the hood is raised. It can start anytime the ignition hood to assist in jump-starting.
Page 401: Jump-Starting Procedure
IN CASE OF EMERGENCY 399 4. If using another vehicle to jump-start the battery, park Connecting The Jumper Cables the vehicle within the jumper cables reach, set the 1. Connect the positive (+) end of the jumper cable to the parking brake and make sure the ignition is OFF.
Page 402: Refueling In Emergency
400 IN CASE OF EMERGENCY If frequent jump-starting is required to start your vehicle CAUTION! you should have the battery and charging system tested at your authorized dealer. Do not run the booster vehicle engine above 2000 rpm since it provides no charging benefit, wastes fuel and CAUTION! can damage booster vehicle engine.
Page 403: Manual Park Release
IN CASE OF EMERGENCY 401 MANUAL PARK RELEASE 2. Open the center console and locate the Manual Park Release cover, remove it by snapping the cover away from the console hinges. WARNING! Always secure your vehicle by fully applying the parking brake, before activating the Manual Park Release.
Page 404 402 IN CASE OF EMERGENCY 3. Using a screwdriver or similar tool, push the metal latch 4. While the metal latch is in the open position, simulta- in towards the tether strap. neously pull upwards on the tether strap until the lever clicks and latches in the released position.
Page 405: Freeing A Stuck Vehicle
IN CASE OF EMERGENCY 403 To Disengage the Manual Park Release Lever: 2. Once the tension has been released and the lever has been unlocked be sure it is stowed properly and locks 1. To disengage the Manual Park Release apply tension into position.
Page 406 404 IN CASE OF EMERGENCY wheels. Push and hold the lock button on the gear selector. WARNING! (Continued) Then shift back and forth between DRIVE and REVERSE injure someone. Do not spin your vehicle’s wheels while gently pressing the accelerator. faster than 30 mph (48 km/h) or for longer than 30 NOTE: Shifts between DRIVE and REVERSE can only be seconds continuously without stopping when you are...
Page 407: Towing A Disabled Vehicle
IN CASE OF EMERGENCY 405 ENHANCED ACCIDENT RESPONSE SYSTEM CAUTION! (Continued) (EARS) • Revving the engine or spinning the wheels too fast This vehicle is equipped with an Enhanced Accident may lead to transmission overheating and failure. It Response System. can also damage the tires.
Page 409 SERVICING AND MAINTENANCE CONTENTS ▫ Brake System ......438 SCHEDULED SERVICING ....409 ▫...
Page 410 408 SERVICING AND MAINTENANCE ▫ Body And Underbody Maintenance ..465 DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES ....463 ▫...
Page 411: Scheduled Servicing
SERVICING AND MAINTENANCE 409 SCHEDULED SERVICING NOTE: • The oil change indicator message will not monitor the The Scheduled Maintenance services listed in this manual must be done at the times or mileages specified to protect time since the last oil change. Change your vehicle’s oil your vehicle warranty and ensure the best vehicle perfor- if it has been six months since your last oil change, even mance and reliability.
Page 412: Maintenance Plan - Srt
410 SERVICING AND MAINTENANCE Once A Month At Each Oil Change • Check tire pressure and look for unusual wear or • Change the engine oil filter. damage. • Inspect the brake hoses and lines. • Inspect the battery, and clean and tighten the terminals as required.
Page 413 SERVICING AND MAINTENANCE 411 Miles: Or Months: 96 102 108 114 120 126 132 138 144 150 Or Kilometers: If using your vehicle for any of the following: dusty or off-road conditions. Inspect the engine air cleaner filter; replace if neces- sary.
Page 414 412 SERVICING AND MAINTENANCE Miles: Or Months: 96 102 108 114 120 126 132 138 144 150 Or Kilometers: Inspect front suspension, tie rod ends, and boot seals, for cracks or leaks and all parts for dam- age, wear, improper looseness or end play;...
Page 415 SERVICING AND MAINTENANCE 413 WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic.
Page 416: Engine Compartment
414 SERVICING AND MAINTENANCE ENGINE COMPARTMENT 6.4L Engine 1 — Remote Jump Start Positive Terminal 6 — Air Cleaner Filter 2 — Power Distribution Center (Fuses) 7 — Washer Fluid Reservoir 3 — Engine Oil Dipstick 8 — Coolant Pressure Cap (Radiator) 4 —...
Page 417 SERVICING AND MAINTENANCE 415 Checking Oil Level — Gasoline Engine The fluid reservoir for the windshield washers and the rear window washer is shared. The fluid reservoir is located in To assure proper lubrication of your vehicle’s engine, the the engine compartment, be sure to check the fluid level at engine oil must be maintained at the correct level.
Page 418: Dealer Service
416 SERVICING AND MAINTENANCE WARNING! CAUTION! (Continued) negative post. Battery posts are marked positive (+) • Battery fluid is a corrosive acid solution and can and negative (-) and are identified on the battery burn or even blind you. Do not allow battery fluid to case.
Page 419: Engine Oil
SERVICING AND MAINTENANCE 417 The manufacturer recommends the use of Pennzoil Ultra WARNING! 0W-40 engine or equivalent MOPAR oil meeting the FCA Material Standard MS-12633 for use in all operating tem- You can be badly injured working on or around a peratures.
Page 420 418 SERVICING AND MAINTENANCE American Petroleum Institute (API) Engine Oil The engine oil filler cap also shows the recommended Identification Symbol engine oil viscosity for your engine. For information on engine oil filler cap location, refer to “Engine Compart- ment” in this section for further information. This symbol means that the oil has been certified by the American Synthetic Engine Oils...
Page 421: Engine Oil Filter
SERVICING AND MAINTENANCE 419 environment. Contact your authorized dealer, service sta- WARNING! tion or governmental agency for advice on how and where used oil and oil filters can be safely discarded in your area. The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine Engine Oil Filter backfire.
Page 422 420 SERVICING AND MAINTENANCE Engine Air Cleaner Filter Removal 2. Lift the air cleaner cover to access the air cleaner filter. 1. Release the spring clips from the air cleaner cover. Open Air Cleaner Filter Assembly 1 — Air Cleaner Cover Air Cleaner Filter Cover 2 —...
Page 423: Accessory Drive Belt Inspection
SERVICING AND MAINTENANCE 421 3. Remove the air cleaner filter element from the housing 2. Install the air cleaner cover onto the housing assembly assembly. locating tabs. 3. Latch the spring clips and lock the air cleaner cover to the housing assembly. Accessory Drive Belt Inspection WARNING! •...
Page 424: Air Conditioner Maintenance
422 SERVICING AND MAINTENANCE • Belt slips However, cracks running along a rib (not across) are not normal. Any belt with cracks running along a rib must be • “Groove jumping (belt does not maintain correct posi- replaced. Also have the belt replaced if it has excessive tion on pulley) wear, frayed cords or severe glazing.
Page 425 SERVICING AND MAINTENANCE 423 Refrigerant Recovery And Recycling R134a — If WARNING! Equipped • Use only refrigerants and compressor lubricants ap- R-134a Air Conditioning Refrigerant is a hydrofluoro- proved by the manufacturer for your air conditioning carbon (HFC) that is endorsed by the Environmental system.
Page 426 424 SERVICING AND MAINTENANCE Air Conditioning Filter Replacement (A/C Air Filter) Refer to “Scheduled Servicing” in this section for the proper maintenance intervals. WARNING! Do not remove the cabin air filter while the vehicle is running, or while the ignition is in the ACC or ON/ RUN mode.
Page 427 SERVICING AND MAINTENANCE 425 NOTE: When disengaging the glove compartment door 5. Remove the filter cover by disengaging the retaining tab from its hinges, there will be some resistance. and mid way snap that secures the filter cover to the HVAC housing.
Page 428: Body Lubrication
426 SERVICING AND MAINTENANCE 7. Install the A/C air filter with the arrow on the filter Body Lubrication pointing toward the floor. When installing the filter Locks and all body pivot points, including such items as cover, make sure the retaining tabs fully engage the seat tracks, door hinge pivot points and rollers, liftgate, cover.
Page 429: Windshield Wiper Blades
SERVICING AND MAINTENANCE 427 Windshield Wiper Blades The wiper blades and wiper arms should be inspected periodically, not just when wiper performance problems Clean the rubber edges of the wiper blades and the are experienced. This inspection should include the follow- windshield periodically with a sponge or soft cloth and a ing points: mild nonabrasive cleaner.
Page 430 428 SERVICING AND MAINTENANCE Front Wiper Blade Removal/Installation CAUTION! Do not allow the wiper arm to spring back against the glass without the wiper blade in place or the glass may be damaged. 1. Lift the wiper arm to raise the wiper blade off of the glass, until the wiper arm is in the full up position.
Page 431 SERVICING AND MAINTENANCE 429 2. To disengage the wiper blade from the wiper arm, flip with one hand and separating the wiper blade from the up the release tab on the wiper blade and while holding wiper arm with the other hand (move the wiper blade the wiper arm with one hand, slide the wiper blade toward the right side of the vehicle to separate the wiper down towards the base of the wiper arm.
Page 432 430 SERVICING AND MAINTENANCE Installing The Front Wipers NOTE: The rear wiper arm cannot be fully raised off the glass unless the wiper arm pivot cap is unsnapped first. 1. Lift the wiper arm off of the glass, until the wiper arm is Attempting to fully raise the rear wiper arm without in the full up position.
Page 433 SERVICING AND MAINTENANCE 431 2. Lift the rear wiper arm fully off the glass. NOTE: Resistance will be accompanied by an audible snap. 4. Still grasping the bottom end of the wiper blade, move the wiper blade upward and away from the wiper arm to disengage.
Page 434: Exhaust System
432 SERVICING AND MAINTENANCE Installing The Rear Wiper have an authorized technician inspect the complete ex- haust system and adjacent body areas for broken, dam- 1. Lift the rear wiper arm pivot cap away from the glass to aged, deteriorated, or mispositioned parts. Open seams or allow the rear wiper blade to be raised off of the glass.
Page 435: Cooling System
SERVICING AND MAINTENANCE 433 In unusual situations involving grossly malfunctioning CAUTION! engine operation, a scorching odor may suggest severe and • The catalytic converter requires the use of unleaded abnormal catalyst overheating. If this occurs, stop the vehicle, turn off the engine and allow it to cool. Service, fuel only.
Page 436 434 SERVICING AND MAINTENANCE coolant (antifreeze) from the radiator drain cock. If the cap WARNING! (Continued) is sealing properly, the engine coolant (antifreeze) will see or hear steam coming from under the hood, do not begin to drain from the coolant recovery bottle. DO NOT open the hood until the radiator has had time to cool.
Page 437 SERVICING AND MAINTENANCE 435 Adding Coolant CAUTION! Your vehicle has been built with an improved engine • Mixing of engine coolant (antifreeze) other than coolant (OAT coolant conforming to MS.90032) that allows specified Organic Additive Technology (OAT) en- extended maintenance intervals. This engine coolant (anti- gine coolant (antifreeze), may result in engine dam- freeze) can be used up to ten years or 150,000 miles age and may decrease corrosion protection.
Page 438 436 SERVICING AND MAINTENANCE • Use only high purity water such as distilled or deionized Cooling System Pressure Cap water when mixing the water/engine coolant (anti- The cap must be fully tightened to prevent loss of engine freeze) solution. The use of lower quality water will coolant (antifreeze), and to ensure that engine coolant reduce the amount of corrosion protection in the engine (antifreeze) will return to the radiator from the coolant...
Page 439 SERVICING AND MAINTENANCE 437 Disposal Of Used Engine Coolant Points To Remember Used ethylene glycol-based engine coolant (antifreeze) is a NOTE: When the vehicle is stopped after a few miles/ regulated substance requiring proper disposal. Check with kilometers of operation, you may observe vapor coming your local authorities to determine the disposal rules for from the front of the engine compartment.
Page 440: Brake System
438 SERVICING AND MAINTENANCE • Maintain engine coolant (antifreeze) concentration at a WARNING! minimum of 50% OAT coolant (conforming to MS.90032) and distilled water for proper corrosion pro- Riding the brakes can lead to brake failure and possi- tection of your engine which contains aluminum com- bly a collision.
Page 441: Front/Rear Axle Fluid
SERVICING AND MAINTENANCE 439 WARNING! WARNING! (Continued) • Do not allow petroleum based fluid to contaminate • Use only manufacturer’s recommended brake fluid. the brake fluid. Brake seal components could be Refer to “Fluids And Lubricants” in “Technical damaged, causing partial or complete brake failure. Specifications”...
Page 442: Transfer Case
440 SERVICING AND MAINTENANCE Rear Axle Fluid Level Check Adding Fluid The rear axle oil level needs to be no lower than 1/8 in Add fluid at the filler hole, until it runs out of the hole, (3 mm) below the bottom of the fill hole. when the vehicle is in a level position.
Page 443 SERVICING AND MAINTENANCE 441 for fluid specifications. It is important to maintain the CAUTION! transmission fluid at the correct level using the recom- mended fluid. Do not use chemical flushes in your transmission as the chemicals can damage your transmission compo- NOTE: No chemical flushes should be used in any trans- nents.
Page 444: Raising The Vehicle
442 SERVICING AND MAINTENANCE Fluid And Filter Changes Tire Markings Under normal operating conditions, the fluid installed at the factory will provide satisfactory lubrication for the life of the vehicle. Routine fluid and filter changes are not required. However, change the fluid and filter if the fluid becomes contami- nated (with water, etc.), or if the transmission is disas- sembled for any reason.
Page 445 SERVICING AND MAINTENANCE 443 • European — Metric tire sizing is based on European • High flotation tire sizing is based on U.S. design stan- design standards. Tires designed to this standard have dards and it begins with the tire diameter molded into the tire size molded into the sidewall beginning with the the sidewall.
Page 446 444 SERVICING AND MAINTENANCE EXAMPLE: DOT MA L9 ABCD 0301 ABCD = Code used by the tire manufacturer (one to four digits) 03 = Number representing the week in which the tire was manufactured (two digits) – 03 means the 3rd week 01 = Number representing the year in which the tire was manufactured (two digits) –...
Page 447 SERVICING AND MAINTENANCE 445 Term Definition Recommended Cold Tire Inflation Pressure Vehicle manufacturer’s recommended cold tire inflation pressure as shown on the tire placard. Tire Placard A label permanently attached to the vehicle describing the vehicle’s loading capacity, the original equipment tire sizes and the recom- mended cold tire inflation pressures.
Page 448 446 SERVICING AND MAINTENANCE Tire And Loading Information Placard Example Tire Placard Location (B-Pillar) Tire And Loading Information Placard This placard tells you important information about the: • Number of people that can be carried in the vehicle. • Total weight your vehicle can carry. •...
Page 449 SERVICING AND MAINTENANCE 447 Loading Steps For Determining Correct Load Limit— The vehicle maximum load on the tire must not exceed the (1) Locate the statement “The combined weight of load carrying capacity of the tire on your vehicle. You will occupants and cargo should never exceed XXX kg or not exceed the tire’s load carrying capacity if you adhere to XXX lbs.”...
Page 450 448 SERVICING AND MAINTENANCE Metric Example For Load Limit NOTE: • If your vehicle will be towing a trailer, load from your For example, if “XXX” amount equals 635 kg and there will be five 68 kg passengers in your vehicle, the amount of trailer will be transferred to your vehicle.
Page 451 SERVICING AND MAINTENANCE 449 WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the rec- ommended load capacity for your vehicle. Never over- load them.
Page 452: Tires - General Information
450 SERVICING AND MAINTENANCE Tires — General Information WARNING! (Continued) Tire Pressure • Overinflated or underinflated tires can affect vehicle handling and can fail suddenly, resulting in loss of Proper tire inflation pressure is essential to the safe and vehicle control. satisfactory operation of your vehicle.
Page 453 SERVICING AND MAINTENANCE 451 Tread Wear CAUTION! Improper cold tire inflation pressures can cause abnormal After inspecting or adjusting the tire pressure, always wear patterns and reduced tread life, resulting in the need reinstall the valve stem cap. This will prevent moisture for earlier tire replacement.
Page 454 452 SERVICING AND MAINTENANCE pressure should be increased by 3 psi (21 kPa), which Radial Ply Tires equals 1 psi (7 kPa) for every 12°F (7°C) for this outside temperature condition. WARNING! Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) Combining radial ply tires with other types of tires on during operation.
Page 455 SERVICING AND MAINTENANCE 453 Run Flat Tires — If Equipped Tire Spinning Run Flat tires allow you the capability to drive 50 miles When stuck in mud, sand, snow, or ice conditions, do not (80 km) at 50 mph (80 km/h) after a rapid loss of inflation spin your vehicle’s wheels above 30 mph (48 km/h) or for pressure.
Page 456 454 SERVICING AND MAINTENANCE Tread Wear Indicators worn to the tread wear indicators, the tire should be replaced. Refer to “Replacement Tires” in this section for Tread wear indicators are in the original equipment tires to further information. help you in determining when your tires should be re- placed.
Page 457 SERVICING AND MAINTENANCE 455 It is recommended to replace the two front tires or two rear WARNING! (Continued) tires as a pair. Replacing just one tire can seriously affect follow this warning can result in sudden tire failure. your vehicle’s handling. If you ever replace a wheel, make You could lose control and have a collision resulting in sure that the wheel’s specifications match those of the serious injury or death.
Page 458: Tire Types
456 SERVICING AND MAINTENANCE tire sidewall. Use all season tires only in sets of four; failure WARNING! (Continued) to do so may adversely affect the safety and handling of • Never use a tire with a smaller load index or capacity, your vehicle.
Page 459: Spare Tires - If Equipped
SERVICING AND MAINTENANCE 457 Snow Tires Spare Tires — If Equipped Some areas of the country require the use of snow tires NOTE: For vehicles equipped with Tire Service Kit instead during the Winter. Snow tires can be identified by a of a spare tire, please refer to “Tire Service Kit”...
Page 460 458 SERVICING AND MAINTENANCE spare by looking at the spare tire description on the Tire WARNING! (Continued) and Loading Information Placard located on the driver’s needs to be replaced. Be sure to follow the warnings, side door opening or on the sidewall of the tire. Compact which apply to your spare.
Page 461: Wheel And Wheel Trim Care
SERVICING AND MAINTENANCE 459 use spare wheel. This label contains the driving limitations WARNING! for this spare. This tire may look like the original equipped tire on the front or rear axle of your vehicle, but it is not. Compact and Collapsible spares are for temporary Installation of this limited use spare tire affects vehicle emergency use only.
Page 462 460 SERVICING AND MAINTENANCE and to prevent corrosion. Wash wheels with the same soap wheel cleaning chemicals and equipment to prevent dam- solution recommended for the body of the vehicle. age to the wheels. Mopar Wheel Treatment or Mopar Chrome Cleaner or their equivalent is recommended or Your wheels are susceptible to deterioration caused by salt, select a non-abrasive, non-acidic cleaner for aluminum or sodium chloride, magnesium chloride, calcium chloride,...
Page 463: Tire Chains (Traction Devices)
SERVICING AND MAINTENANCE 461 Dark Vapor Or Black Satin Chrome Wheels WARNING! CAUTION! Using tires of different size and type (M+S, Snow) between front and rear axles can cause unpredictable If your vehicle is equipped with Dark Vapor or Black handling.
Page 464: Tire Rotation Recommendations
462 SERVICING AND MAINTENANCE NOTE: The premium Tire Pressure Monitor System will CAUTION! (Continued) automatically locate the pressure values displayed in the • Observe the traction device manufacturer’s instruc- correct vehicle position following a tire rotation. tions on the method of installation, operating speed, The suggested rotation method is the “rearward-cross”...
Page 465: Servicing And Maintenance
SERVICING AND MAINTENANCE 463 DEPARTMENT OF TRANSPORTATION UNIFORM specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. TIRE QUALITY GRADES The following tire grading categories were established by WARNING! the National Highway Traffic Safety Administration. The specific grade rating assigned by the tire’s manufacturer in The traction grade assigned to this tire is based on each category is shown on the sidewall of the tires on your...
Page 466: Storing The Vehicle
464 SERVICING AND MAINTENANCE • Clean and protect the painted parts by applying protec- WARNING! tive waxes. The temperature grade for this tire is established for a • Clean and protect polished metal parts by applying tire that is properly inflated and not overloaded. Ex- protective waxes.
Page 467: Bodywork
SERVICING AND MAINTENANCE 465 What Causes Corrosion? CAUTION! Corrosion is the result of deterioration or removal of paint Before removal of the positive and negative terminals and protective coatings from your vehicle. to the battery, wait at least a minute with ignition The most common causes are: switch in the OFF position and close the driver’s door.
Page 468: Preserving The Bodywork
466 SERVICING AND MAINTENANCE Do not use abrasive cleaning components, solvents, steel CAUTION! (Continued) wool or other aggressive material to clean the lenses. • Use of power washers exceeding 1,200 psi (8 274 kPa) Preserving The Bodywork can result in damage or removal of paint and decals. Washing Special Care •...
Page 469: Interiors
SERVICING AND MAINTENANCE 467 • If you carry special cargo such as chemicals, fertilizers, Seat Belt Maintenance de-icer salt, etc., be sure that such materials are well Do not bleach, dye or clean the belts with chemical solvents packaged and sealed. or abrasive cleaners.
Page 470: Plastic And Coated Parts
468 SERVICING AND MAINTENANCE Plastic And Coated Parts Leather Parts Use MOPAR Total Clean to clean vinyl upholstery. MOPAR Total Clean is specifically recommended for leather upholstery. CAUTION! Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can •...
Page 471: Glass Surfaces
SERVICING AND MAINTENANCE 469 NOTE: If equipped with light colored leather, it tends to Glass Surfaces show any foreign material, dirt, and fabric dye transfer All glass surfaces should be cleaned on a regular basis with more so than darker colors. The leather is designed to for MOPAR Glass Cleaner, or any commercial household-type easy cleaning, and FCA recommends MOPAR total care glass cleaner.
Page 473: Technical Specifications
TECHNICAL SPECIFICATIONS CONTENTS ▫ CNG And LP Fuel System Modifications ..476 VEHICLE IDENTIFICATION NUMBER ..472 ▫ MMT In Gasoline ..... . .476 WHEEL AND TIRE TORQUE SPECIFICATIONS .
Page 474: Vehicle Identification Number
472 TECHNICAL SPECIFICATIONS VEHICLE IDENTIFICATION NUMBER The Vehicle Identification Number (VIN) is found on a plate located on the left front corner of the instrument panel pad, visible from outside of the vehicle through the windshield. This number also is stamped into the right front body, behind the right front seat.
Page 475: Wheel And Tire Torque Specifications
TECHNICAL SPECIFICATIONS 473 WHEEL AND TIRE TORQUE SPECIFICATIONS Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles. Proper lug nut/bolt torque is very important to ensure that the wheel is properly mounted to the vehicle. Any time a wheel has been removed and reinstalled on the vehicle, the lug nuts/bolts should be torqued using a properly cali- brated torque wrench.
Page 476: Fuel Requirements
474 TECHNICAL SPECIFICATIONS Tighten the lug nuts/bolts in a star pattern until each FUEL REQUIREMENTS nut/bolt has been tightened twice. 6.4L Engine After 25 miles (40 km) check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against This engine is designed to meet all emis- the wheel.
Page 477: Reformulated Gasoline
TECHNICAL SPECIFICATIONS 475 Reformulated Gasoline gasoline is recommended. Visit www.toptiergas.com for a list of TOP TIER Detergent Gasoline Retailers. Many areas of the country require the use of cleaner burning gasoline referred to as “Reformulated Gasoline”. Indiscriminate use of fuel system cleaning agents should be Reformulated gasoline contains oxygenates and are specifi- avoided.
Page 478: E-85 Usage In Non-Flex Fuel Vehicles
476 TECHNICAL SPECIFICATIONS are not the responsibility of the manufacturer and may CNG And LP Fuel System Modifications void or not be covered under New Vehicle Limited Modifications that allow the engine to run on compressed Warranty. natural gas (CNG) or liquid propane (LP) may result in damage to the engine, emissions, and fuel system compo- E-85 Usage In Non-Flex Fuel Vehicles nents.
Page 479: Fuel System Cautions
TECHNICAL SPECIFICATIONS 477 Fuel System Cautions NOTE: Intentional tampering with the emissions control system can result in civil penalties being assessed against you. CAUTION! Carbon Monoxide Warnings Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gasoline is prohibited by Federal WARNING! law.
Page 480: Fluid Capacities
478 TECHNICAL SPECIFICATIONS FLUID CAPACITIES U.S. Metric Fuel (Approximate) 24.6 Gallons 93.0 Liters Engine Oil With Filter 6.4 Liter Engine (SAE 0W-40, Synthetic API Certified) 7 Quarts 6.6 Liters Cooling System* 6.4 Liter Engine (MOPAR Antifreeze/Engine Coolant 10 Year/ 16 Quarts 15.5 Liters 150,000 Mile Formula that meets the requirements of FCA Material Standard MS.90032.
Page 481: Fluids And Lubricants
TECHNICAL SPECIFICATIONS 479 FLUIDS AND LUBRICANTS Engine Component Fluid, Lubricant or Genuine Part Engine Coolant We recommend you use MOPAR Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Tech- nology) that meets the requirements of FCA Material Standard MS.90032. Engine Oil For best performance and maximum protection under all types of operating conditions, the manufacturer only rec- ommends full synthetic engine oils that meet the American...
Page 482: Chassis
480 TECHNICAL SPECIFICATIONS Chassis Component Fluid, Lubricant, or Genuine Part Automatic Transmission Use only Mopar ZF 8&9 Speed ATF Automatic Transmission Fluid or equivalent. Failure to use the correct fluid may affect the function or performance of your transmission. Transfer Case – Single-Speed (Selec-Track) We recommend you use MOPAR ATF+4 Automatic Trans- mission Fluid.
Page 483 MULTIMEDIA CONTENTS ▫ Custom Mode ......511 UCONNECT RADIOS ....484 PERSONALIZED MENU BAR .
Page 484 482 MULTIMEDIA ▫ Replacing The Headphone Batteries ..538 STEERING WHEEL AUDIO CONTROLS — IF EQUIPPED ......526 ▫...
Page 485 MULTIMEDIA ▫ Register (8.4/8.4 NAV) ....553 ▫ Siri Eyes Free — If Equipped ....558 ▫...
Page 486: Uconnect Radios
484 MULTIMEDIA UCONNECT RADIOS 1. Press the “Apps ” button to open the App screen. For detailed information about your Uconnect radio, refer 2. Press and hold, then drag the selected App to replace an to your Uconnect Owner’s Manual Supplement. existing shortcut in the main menu bar.
Page 487 MULTIMEDIA The risk of unauthorized and unlawful access to your NOTE: vehicle systems may still exist, even if the most recent • FCA US LLC or your dealer may contact you directly version of vehicle software (such as Uconnect software) is regarding software updates.
Page 488: Uconnect Settings
486 MULTIMEDIA UCONNECT SETTINGS Buttons On The Faceplate The Uconnect system uses a combination of buttons on the Buttons on the faceplate are located below the Uconnect touchscreen and buttons on the faceplate located on the system in the center of the instrument panel. In addition, center of the instrument panel that allow you to access and there is a Scroll/Enter control knob located on the right change the customer programmable features.
Page 489: Customer Programmable Features - Uconnect 8.4
MULTIMEDIA Customer Programmable Features — Uconnect 8.4 NOTE: Settings • Only one touchscreen area may be selected at a time. Press the “Apps ” button, then press the “Settings” • Depending on the vehicles options, feature settings may button on the touchscreen to display the menu setting vary.
Page 490 488 MULTIMEDIA Display After pressing the “Display” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Display Mode Manual Auto Display Brightness With Headlights ON NOTE: To make changes to the Display Brightness with Headlights ON setting, the headlights must be on and the interior dimmer switch must not be in the party or parade positions.
Page 491 MULTIMEDIA Setting Name Selectable Options Set Language NOTE: When the “Set Language” feature is selected, you may select one of multiple languages (English / Français / Espa- ñol) for all display nomenclature, including the trip functions and the navigation system (if equipped). Press the “Set Language”...
Page 492 490 MULTIMEDIA Setting Name Selectable Options Nav Next Turn Pop-up in Cluster NOTE: When the “Navigation Turn-By-Turn In Cluster” feature is selected, the turn-by-turn directions will appear in the in- strument cluster display as the vehicle approaches a designated turn within a programmed route. Phone Pop-ups Displayed in Cluster Units...
Page 493 MULTIMEDIA Voice After pressing the “Voice” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Voice Response Length Brief Detailed Show Command List Always With Help Never Clock After pressing the “Clock” button on the touchscreen, the following settings will be available: Setting Name Selectable Options...
Page 494 492 MULTIMEDIA Setting Name Selectable Options Set Time Minutes NOTE: The “Set Time Minutes” feature will allow you to adjust the minutes. The “Sync time with GPS” button on the touch- screen must be unchecked. Time Format 12hrs 24hrs Safety/Assistance After pressing the “Safety/Assistance”...
Page 495 MULTIMEDIA Setting Name Selectable Options ParkView Backup Camera Active Guide Lines — If Equipped NOTE: The “ParkView Backup Camera Active Guide Lines” feature overlays the Rear Backup Camera image with active, or dynamic, grid lines to help illustrate the width of the vehicle and its project back up path, based on the steering wheel position when the option is checked.
Page 496 494 MULTIMEDIA Setting Name Selectable Options Forward Collision Near Warning-Plus (FCW+) — If Equipped NOTE: The “Forward Collision Warning Plus (FCW+) Sensitivity” setting determines at what relative distance the vehicle directly in front of you needs to be at, before the system will warn you of a possible collision with the vehicle directly in front of you, based on the option is selected.
Page 497 MULTIMEDIA Setting Name Selectable Options ParkSense — If Equipped Sound Only Sound and Display NOTE: The “ParkSense” system setting will scan for objects behind the vehicle when the transmission gear selector is in RE- VERSE and the vehicle speed is less than 7 mph (11 km/h), when enabled. It will provide an alert (audible and/or visual) to indicate the proximity to other objects.
Page 498 496 MULTIMEDIA Setting Name Selectable Options Lane Departure Strength Medium High (LDW) — If Equipped Blind Spot Alert — If Lights Lights and Chime Equipped NOTE: When the “Blind Spot Alert” feature is selected, the Blind Spot Monitor (BSM) system is activated and will show a visual alert in the outside mirrors, or it will show a visual alert in the outside mirrors as well as play an audible alert when the turn signal is on.
Page 499 MULTIMEDIA Lights After pressing the “Lights” button on the touchscreen the following settings will be available. Setting Name Selectable Options Headlight Off Delay 0 sec 30 sec 60 sec 90 sec NOTE: When the “Headlight Off Delay” feature is selected, it allows the adjustment of the amount of time the headlights remain on after the engine is shut off.
Page 500 498 MULTIMEDIA Setting Name Selectable Options Daytime Running Lights — If Equipped Flash Lights With Lock Doors & Locks After pressing the “Doors & Locks” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Auto Door Locks NOTE: When the “Auto Door Locks”...
Page 501 MULTIMEDIA Setting Name Selectable Options Flash Lights With Lock Sound Horn With Lock 1st Press 2nd Press Sound Horn With Remote Start 1st Press Of Key Fob Unlocks Driver Door All Doors NOTE: When Driver Door is selected with 1st Press Of Key Fob Unlocks, only the driver’s door will unlock with the first press of the key fob UNLOCK button.
Page 502 500 MULTIMEDIA Setting Name Selectable Options Personal Settings Linked to Key Fob — If Equipped NOTE: This feature provides automatic recall of all settings stored to a memory location (driver’s seat, exterior mirrors, steer- ing column position and radio station pre-sets) to enhance driver mobility when entering and exiting the vehicle. Power Lift Gate Alert —...
Page 503 MULTIMEDIA Audio After pressing the “Audio” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Balance/Fade Speaker Icon NOTE: When in this display you may adjust the “Balance/Fade” of the audio by pressing and dragging the “Speaker Icon” toward any location in the box.
Page 504 502 MULTIMEDIA Phone/Bluetooth After pressing the “Phone/Bluetooth” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Do Not Disturb Do Not Disturb Options Paired Phones List Of Paired Phones NOTE: This feature shows which phones are paired to the Phone/Bluetooth system. For further information, refer to the Uconnect Owner’s Manual Supplement.
Page 505 MULTIMEDIA SiriusXM Setup — If Equipped After pressing the “SiriusXM Setup” button on the touchscreen the following settings will be available: Setting Name Selectable Options SXM Tune Start NOTE: The “Tune Start” feature begins playing the current song from the beginning when you tune to a music channel using one of the twelve presets, so you can enjoy the complete song.
Page 506 504 MULTIMEDIA Restore Settings After pressing the “Restore Settings” button on the touch- screen the following settings will be available: Setting Name Selectable Options Restore Settings Cancel NOTE: When this feature is selected it will reset all settings to their default settings. Clear Personal Data After pressing the “Clear Personal Data”...
Page 507 MULTIMEDIA System Information After pressing the “System Information” button on the touchscreen, the following settings will be available: Setting Name Selectable Options System Information System Software Information Screen NOTE: When this feature is selected, a “System Information” screen will appear, displaying the system software version.
Page 508: Srt Drive Modes
506 MULTIMEDIA • Pushing the SRT button on the Selec-Track switch. SRT DRIVE MODES • Pushing the Custom button on the Selec-Track switch. • Selecting “Drive Modes” from the “Apps” menu. • Selecting “Drive Modes” from within the Performance Pages menu. The SRT Drive Modes main screen displays the current drive mode and real-time status of the vehicle’s perfor- mance configuration.
Page 509: Track Mode
MULTIMEDIA Listed below are the available Drive Modes: NOTE: Electronic Stability Control (ESC) Full-Off can be activated by pushing and holding the ESC Off button on Track Mode the instrument panel switch bank for five seconds. Sport Mode Drive Modes (Track) Selecting “Track”...
Page 510: Tow Mode
508 MULTIMEDIA Suspension systems are all set to their “Sport” settings Stability Control is set to “Full” highlighted in blue. highlighted in orange. The Paddle Shifters are enabled. All-Wheel Drive is set to “50/50” highlighted in blue. Steering is set to “Street” highlighted in yellow. Suspension Tow Mode is set to “Sport”...
Page 511 MULTIMEDIA Snow mode (depending on certain operating conditions), the transmission may use second gear (rather than first gear) during launches, to minimize wheel slippage. The Transmission is set to “Snow” setting highlighted in blue. Stability Control is set to “Full” highlighted in blue. All-Wheel Drive is set to “50/50”...
Page 512: Auto Mode
510 MULTIMEDIA Auto Mode Suspension can be configured in either the “Street,” “Sport,” or “Track” and the Paddle Shifters may be enabled or disabled while in auto set-up mode. Drive Mode Auto (Default) Auto Mode (Default) Auto mode is enabled upon ignition on, or by selecting “Auto”...
Page 513: Custom Mode
MULTIMEDIA Custom Mode the All-Wheel Drive, Stability Control, Transmission, Steer- ing, Suspension, and Paddle Shifter settings are shown in their current configuration. While in the Custom Mode screen, press the “Custom Set-Up” button on the touchscreen to access the selectable options.
Page 514: Race Options
512 MULTIMEDIA RACE OPTIONS Launch Control WARNING! Launch Mode is intended for off-highway or off-road use only and should not be used on any public roadways. It is recommended that this feature be used in a controlled environment, and within the limits of the law.
Page 515 MULTIMEDIA Launch Control button on the Selec-Track Switch, or by pressing the “Cancel Launch Mode” button on the touch- screen. NOTE: Launch RPM Set-Up cannot be accessed unless Launch Mode is deactivated. Activate Launch Control Launch Control can be accessed by pushing the Launch button on the Selec-Track switch or pushing the SRT button on the Selec-Track switch then selecting the “Race Options”...
Page 516: Shift Light
514 MULTIMEDIA To adjust the Launch RPM, drag the slider bar or press the within the instrument cluster display. This feature is a arrows on the touchscreen to adjust the holding RPM. The visual cue to manually up-shift using the paddle shifters. launch RPM limit is between 1500 and 3500 RPM.
Page 517: Srt Performance Pages
MULTIMEDIA factory default” button on the touchscreen to change back to factory settings, or press the “Shift Light Off” button on the touchscreen to turn the system off completely. SRT PERFORMANCE PAGES Performance Pages is an application that provides a dis- play for performance indicators, as received from the instrument cluster, that will help you gain familiarity with the capabilities of your SRT vehicle in real-time.
Page 518: Home
516 MULTIMEDIA Home WARNING! (Continued) of the law. The capabilities of the vehicle as measured by the Performance Pages must never be exploited in a reckless or dangerous manner, which can jeopardize the user’s safety or the safety of others. Only a safe, attentive, and skillful driver can prevent accidents.
Page 519: Timers
MULTIMEDIA Timers When the Timers Page is selected, you will be able to select from following “Tickets”: • Recent Pressing the “Recent” button displays a “real time” sum- mary of performance timers. • Last Pressing the “Last” button displays the last recorded run of performance timers.
Page 520 518 MULTIMEDIA • Press the “Uconnect” button to save the runs to the USB or SD card which will continue to take save files until full. The operation of the Save feature is listed below: Owner web page. • Press the “Cancel” button to view the last timer “Ticket.” The “Tickets”...
Page 521 MULTIMEDIA • 60 ft (18 Meters) time Gauges 1 Displays the time it takes for the vehicle to go 60 ft. • Brake Distance Displays the distance it takes the vehicle to make a full stop. Contains current and last data for distance and start –...
Page 522: Gauges 1
520 MULTIMEDIA • Oil Pressure When selected, this screen displays the following values: • Intake Air Temperature Shows the actual oil pressure. Shows the actual intake air temperature. Gauges 2 • Battery Voltage Shows the actual battery voltage. • Transmission Temperature Shows the actual transmission temperature.
Page 523: G-Force
MULTIMEDIA G-Force When G-Force is selected, the following features will be available: • Lateral G-Force Left and Right The lateral g-force measures the (sideways) left and right force of the vehicle. • Longitudinal G-Force Acceleration and Braking The longitudinal g-force measures the acceleration and braking force of the vehicle.
Page 524: Engine
522 MULTIMEDIA The zero degree measurement indicates a steering wheel When selected, this screen displays the following values: straight ahead position. When the steering angle value is • Vehicle Speed negative, this indicates a turn to the left, and when the Shows the actual vehicle speed in mph or km/h.
Page 525: Valet Mode
MULTIMEDIA VALET MODE While in Valet Mode the following vehicle configurations are set and locked to prevent unauthorized modification: • All-Wheel Drive is set to 50/50. • Transmission locks out access to first gear and up-shifts earlier than normal. • Stability Control, Steering, and Suspension are set to their STREET settings.
Page 526 524 MULTIMEDIA To exit Valet Mode you must enter the same 4 digit PIN that was used to enter the mode. The unlock keypad can be accessed by either pushing the SRT button on Selec-Track switch, or pressing the “Valet” button on the touchscreen. Valet Mode Deactivation Valet Mode Deactivation PIN...
Page 527: Eco Mode
MULTIMEDIA The Valet Mode Deactivation key pad will then prompt ECO MODE you for your 4 digit PIN code, enter your PIN code and press the “OK” button on the touchscreen. Your vehicle will return to the default state after a key cycle. NOTE: If your 4 digit PIN is lost or forgotten, the vehicle will exit Valet Mode after a battery disconnect for approxi- mately one minute.
Page 528: Steering Wheel Audio Controls - If Equipped
526 MULTIMEDIA The Paddle Shifters will be disabled while in ECO mode. The right-hand control is a rocker-type switch with a push-button in the center and controls the volume and • Changing the Drive Mode will deactivate ECO. mode of the sound system. Pushing the top of the rocker •...
Page 529: Cd Player
MULTIMEDIA CD Player UCONNECT REAR SEAT ENTERTAINMENT (RSE) SYSTEM — IF EQUIPPED Pushing the top of the switch once will go to the next track on the CD. Pushing the bottom of the switch once will go Your Rear Seat Entertainment System is designed to give to the beginning of the current track, or to the beginning of your family years of enjoyment.
Page 530 528 MULTIMEDIA RSE System Screen RSE System Channel 1 (Rear 1) • Place the ignition in the ON or ACC position. • With the Dual Video Screen System, Channel 1 (Rear 1) on the remote control and headphones, refers to •...
Page 531: Dual Video Screen
MULTIMEDIA RSE System Remote Control Channel Selectors RSE System Headphone Channel Selectors • The system can be controlled by the front seat occupants utilizing either the touchscreen radio, or by the rear seat occupants using the remote control. Dual Video Screen NOTE: Typically there are two different ways to operate the features of the Rear Seat Entertainment System.
Page 532: Blu-Ray Disc Player
530 MULTIMEDIA Blu-ray Disc Player 2. To watch a Blu-ray disc on Rear 1 for driver’s side rear passengers, ensure the Remote Control and Headphone Play A Blu-ray Disc switch is on Rear 1. The Blu-ray disc player is located in the center console. 3.
Page 533 MULTIMEDIA Using The Touchscreen Radio 3. RSE Mute Mute rear headphones for the current ignition cycle. Press- ing mute again will unmute rear headphones. 4. RSE Remote Control Lock Out Press to enable/disable remote control functions. 5. RSE Channel 2 Mode Indicates the current source for Screen 2/Channel 2.
Page 534: Play Video Games
532 MULTIMEDIA 8. RSE Mode Select this button to change source for the active (high- lighted) rear Screen/Channel on the rear media control screen. • Press the Media button on the touchscreen, and then press the rear media button on the touchscreen. •...
Page 535: Play A Dvd/Blu-Ray Disc Using The Touchscreen
MULTIMEDIA 3. Left audio in (white). Using The Remote Control 4. Video in (yellow). 1. Push the SOURCE button on the Remote Control. NOTE: Certain high-end video games consoles may exceed 2. While looking at Rear 1 or 2, highlight DISC by either the power limit of the vehicle’s Power Inverter.
Page 536 534 MULTIMEDIA Using The Touchscreen Radio Controls 1. Press the Media button on the Uconnect radio touch- screen. 2. Press the Rear Media button to display the Rear Media Control screen. Rear Seat Entertainment Source Screen NOTE: Pressing the screen on the radio while a DVD or Blu-ray Disc is playing, brings up the basic remote control functions for DVD play such as scene selection, Play, Pause, FF, RW, and Stop.
Page 537: Important Notes For Dual Video Screen System
MULTIMEDIA Important Notes For Dual Video Screen System Blu-ray Disc Player Remote Control — If Equipped • The Rear Seat Entertainment System is able to transmit two channels of stereo audio and video simultaneously. • The Blu-ray Disc Player can play CDs, DVDs and Blu-ray Discs.
Page 538: Headphones Operation
536 MULTIMEDIA 3. SOURCE — Push to enter Source Selection screen. — Push and hold to fast rewind through the current audio track or video chapter. 4. Channel/Screen Selector Switch — Indicates which channel is being controlled by the remote control. When —...
Page 539: Controls
MULTIMEDIA NOTE: The rear video system must be turned on before sound can be heard from the headphones. To conserve battery life, the headphones will automatically turn off approximately three minutes after the rear video system is turned off. Changing the Audio Mode for Headphones 1.
Page 540: Replacing The Headphone Batteries
538 MULTIMEDIA 4. When the Mode Selection menu appears on screen, use How Long Does the Coverage Last? This warranty lasts as the cursor buttons on the remote control to navigate to long as you own the Product. the available modes and push the OK button to select What Does This Warranty Cover? Except as specified the new mode.
Page 541 MULTIMEDIA What Will Unwired Do? Unwired, at its option, will repair Display Settings or replace any defective Product. Unwired reserves the right to replace any discontinued Product with a compa- rable model. THIS WARRANTY IS THE SOLE WAR- RANTY FOR THIS PRODUCT, SETS FORTH YOUR EX- CLUSIVE REMEDY REGARDING...
Page 542 540 MULTIMEDIA control’s navigation buttons ( , ) to change the value for remote control’s power button to turn audio on. If audio is the currently selected item. To reset all values back to the still not heard, check that fully charged batteries are original settings, select the Default Settings menu option installed in the headphones.
Page 543 MULTIMEDIA • For multi-session CDs that contain only multiple CD- (most DVD-Audio discs also have a Video title, but the Video title is ignored). All multi-channel program material Audio sessions, the player will renumber the tracks so is automatically mixed down to two channels, which may each track number is unique.
Page 544 542 MULTIMEDIA • If you are creating your own files, the recommended Compressed Audio Files (MP3 and WMA) fixed bit rate for MP3 files is between 96 and 192Kbps The Blu-ray Disc player is capable of playing MP3 and the recommended fixed bit rate for WMA files is (MPEG-1 Audio Layer 3) and WMA (Windows Media between 64 and 192Kbps.
Page 545: Radio Operation And Mobile Phones
MULTIMEDIA The Blu-ray Disc player may shut down during extremely RADIO OPERATION AND MOBILE PHONES hot conditions, such as when the vehicle’s interior tem- Under certain conditions, the mobile phone being on in perature is above 120° F (48.9° C). When this occurs, the your vehicle can cause erratic or noisy performance from player will display High Temp and will shut off the Rear your radio.
Page 546 544 MULTIMEDIA The radio manufacturer believes the internal wireless radio NOTE: is safe for use by consumers. The level of energy emitted is • This equipment has been tested and found to comply far less than the electromagnetic energy emitted by wire- with the limits for a Class B digital device, pursuant to less devices such as mobile phones.
Page 547: Tips
MULTIMEDIA UCONNECT VOICE RECOGNITION QUICK TIPS If you see the icon on your touchscreen, you have the Uconnect 8.4 NAV system. If not, you have a Uconnect Introducing Uconnect 8.4 system. Start using Uconnect Voice Recognition with these helpful Get Started quick tips.
Page 548: Basic Voice Commands
546 MULTIMEDIA • Cancel to stop a current voice session • Help to hear a list of suggested Voice Commands • Repeat to listen to the system prompts again Notice the visual cues that inform you of your voice recognition system’s status. Cues appear on the touch- screen.
Page 549: Radio
MULTIMEDIA Radio Use your voice to quickly get to the AM, FM or SiriusXM Satellite Radio stations you would like to hear. (Subscrip- tion or included SiriusXM Satellite Radio trial required.) Push the VR button . After the beep, say •...
Page 550: Phone
548 MULTIMEDIA • Change source to Bluetooth • Change source to AUX • Change source to USB • Play artist Beethoven; Play album Greatest Hits; Play song Moonlight Sonata; Play genre Classical TIP: Press the Browse button on the touchscreen to see all of the music on your AUX or USB device.
Page 551: Voice Text Reply
MULTIMEDIA Push the Phone button . After the beep, say one of the following commands • Call John Smith • Dial 123-456-7890 and follow the system prompts • Redial (call previous outgoing phone number) • Call back (call previous incoming phone number) TIP: When providing a Voice Command, push the Phone button and say “Call,”...
Page 552 550 MULTIMEDIA 2. Listen to the Uconnect prompts. After the beep, repeat one of the pre-defined messages and follow the system prompts. PRE-DEFINED VOICE TEXT REPLY RESPONSES Yes. Stuck in traffic. See you later. Start without I’ll be late. Okay. Where are you? I will be <number>...
Page 553: Climate (8.4/8.4 Nav)
MULTIMEDIA Climate (8.4/8.4 NAV) Too hot? Too cold? Adjust vehicle temperatures hands-free and keep everyone comfortable while you keep moving ahead. (If vehicle is equipped with climate control.) Push the VR button . After the beep, say one of the following commands: •...
Page 554: Navigation (8.4 /8.4 Nav)
552 MULTIMEDIA Navigation (8.4 /8.4 NAV) The Uconnect navigation feature helps you save time and become more productive when you know exactly how to get to where you want to go. (Navigation is optional on the Uconnect 8.4 system. See your dealer to activate navigation at any time.) 1.
Page 555: Register (8.4/8.4 Nav)
MULTIMEDIA NOTE: Your vehicle may be transmitting data as autho- Voice Texting rized by the subscriber. Roadside Assistance Call An included trial and/or subscription is required to take 3G Wi-Fi Hotspot*** advantage of the Uconnect Access services in the next **If vehicle is equipped.
Page 556: Vehicle Health Alert
554 MULTIMEDIA 2. Press the “Uconnect Care” button on the touchscreen. Mobile App (8.4/8.4 NAV) You’re only a few steps away from using remote com- 3. A helpful Uconnect Care Agent will register your ve- mands and playing your favorite music in your vehicle. hicle and handle all of the details.
Page 557: Voice Texting (8.4/8.4 Nav)
MULTIMEDIA 3. Press the app you’d like to connect to your vehicle. Voice Texting (8.4/8.4 NAV) 4. Enter your login information for the selected app and 1. To send a message, push the Phone button . After the press Link. beep, say the following command: “Send message to John Smith.”...
Page 558 556 MULTIMEDIA Apple iPhone iOS6 or later supports reading incoming text TIP: messages only. To enable this feature on your Apple • Voice Texting is not compatible with iPhone, but if your iPhone, follow these 4 simple steps: vehicle is equipped with Siri Eyes Free, you can use your voice to send a text message.
Page 559: Yelp (8.4/8.4 Nav)
MULTIMEDIA Yelp (8.4/8.4 NAV) Once registered with Uconnect Access, you can use your voice to search for the most popular places or things around you. 1. Press the “Apps ” button on the touchscreen. 2. Press the “Yelp” button on the touchscreen. 3.
Page 560: Siriusxm Travel Link (8.4/8.4 Nav)
558 MULTIMEDIA SiriusXM Travel Link (8.4/8.4 NAV) Need to find a gas station, view local movie listings, check a sports score or the 5 - day weather forecast? SiriusXM Travel Link is a suite of services that brings a wealth of information right to your Uconnect 8.4 NAV system.
Page 561 MULTIMEDIA To enable Siri push and hold, then release the Uconnect Getting Started Voice Recognition (VR) button on the steering wheel. After Ensure Siri is enabled on your iPhone. you hear a double beep, you can ask Siri to play podcasts and music, get directions, read text messages, and many other useful requests.
Page 562 560 MULTIMEDIA NOTE: A push and release of the button will start normal embedded VR functions. The push and hold, then release of the button will start Siri functions. 2. After the double beep, begin speaking to Siri. Examples of Siri commands and questions: •...
Page 563: Do Not Disturb
MULTIMEDIA NOTE: Do Not Disturb • Speak clearly at a normal pace and volume while With Do Not Disturb, you can disable notifications from facing straight ahead to ensure your command is incoming calls and texts, allowing you to keep your eyes understood.
Page 564: General Information
562 MULTIMEDIA General Information Additional Information This device complies with FCC rules Part 15 and Industry © 2016 FCA US LLC. All rights reserved. Mopar and Canada RSS-210. Operation is subject to the following two Uconnect are registered trademarks and Mopar Owner conditions: Connect is a trademark of FCA US LLC.
Page 565: Cd/Dvd Disc Maintenance
MULTIMEDIA CD/DVD DISC MAINTENANCE 5. Store the disc in its case after playing. To keep a CD/DVD in good condition, take the following 6. Do not expose the disc to direct sunlight. precautions: 7. Do not store the disc where temperatures may become 1.
Page 567 CUSTOMER ASSISTANCE CONTENTS ▫ Customer Assistance For The Hearing Or Speech SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE ......566 Impaired (TDD/TTY) .
Page 568: Suggestions For Obtaining Service For Your Vehicle
566 CUSTOMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR IF YOU NEED ASSISTANCE YOUR VEHICLE The manufacturer and its authorized dealer are vitally interested in your satisfaction. We want you to be happy Prepare For The Appointment with our products and services. If you are having warranty work done, be sure to have the right papers with you.
Page 569: Fca Us Llc Customer Center
CUSTOMER ASSISTANCE 567 Any communication to the manufacturer’s customer center In Mexico Contact should include the following information: Av. Prolongacion Paseo de la Reforma, 1240 • Owner’s name and address Sante Fe C.P. 05109 • Owner’s telephone number (home and office) Mexico, D.
Page 570: Service Contract
568 CUSTOMER ASSISTANCE to a TDD or a conventional teletypewriter (TTY) in the responsible for any service contract other than the manu- United States, can communicate with the manufacturer by facturer’s service contract. If you purchased a service dialing 1-800-380-CHRY. contract that is not a manufacturer’s service contract, and you require service after the manufacturer’s New Vehicle Canadian residents with hearing difficulties that require...
Page 571: Warranty Information
CUSTOMER ASSISTANCE 569 If NHTSA receives similar complaints, it may open an WARNING! (Continued) investigation, and if it finds that a safety defect exists in a California to cause cancer and birth defects, or other group of vehicles, it may order a recall and remedy reproductive harm.
Page 572: Publication Order Forms
570 CUSTOMER ASSISTANCE PUBLICATION ORDER FORMS the first time, using step-by-step troubleshooting and driv- ability procedures, proven diagnostic tests and a complete To order the following manuals, you may use either the list of all tools and equipment. website or the phone numbers listed below. Visa, Master- card, American Express, and Discover orders are accepted.
Page 573 INDEX...
Page 574 572 INDEX Adaptive Cruise Control (ACC) (Cruise Control) ..283 Air Conditioning, Operating Tips ....84 Adding Engine Coolant (Antifreeze) ... . .435 Air Conditioning Refrigerant .
Page 575 INDEX 573 Autostick ......271 Fluid Check ......438, 480 Fluid And Filter Changes .
Page 576 574 INDEX Changing A Flat Tire ......442 Console, Overhead......112 Check Engine Light (Malfunction Indicator Light).
Page 577 INDEX 575 Dipsticks Hazard Warning Flasher ....370 Oil (Engine) ......415 Jacking .
Page 578 576 INDEX Exhaust System ......250, 432 Fuel ........474 Exterior Lights .
Page 579: Introduction
INDEX 577 Hazard Intermittent Wipers (Delay Wipers)....72 Driving Through Flowing, Rising, Or Shallow Introduction ....... .4 Standing Water .
Page 580 578 INDEX Lap/Shoulder Belts ......209 Passing ....... .66 Latches.
Page 581 INDEX 579 Maintenance Schedule ..... . .409 Capacity .......478 Malfunction Indicator Light (Check Engine) .
Page 582 580 INDEX ParkSense System, Rear ....303, 312 Pretensioners Performance ......132, 515 Seat Belts .
Page 583 INDEX 581 Remote Keyless Entry Seat Belt Arm The Alarm ......33 Adjustable Upper Shoulder Belt Anchorage ..213 Disarm The Alarm .
Page 584 582 INDEX Reminder ......141 Siri ....... . .558, 559 Untwisting Procedure .
Page 585 INDEX 583 Wheel, Heated ......57 Compact Spare ......457 Wheel, Tilt .
Page 586 584 INDEX Guide ....... . .358 Turn Signals ......161, 377 Recreational .
Page 587: Windshield
INDEX 585 Washers, Windshield..... .71, 415 Washing Vehicle ......466 Water Driving Through .
Page 588 INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this The antenna cable should be as short as practical and vehicle’s electronic system to provide immunity to radio routed away from the vehicle wiring when possible. Use frequency signals. Mobile two-way radios and telephone only fully shielded coaxial cable.

Jeep Grand Cherokee SRT 2017 Owner's Manual

Introduction

Graphical

Getting to Know Your Vehicle

Getting to Know Your Instrument Panel

Safety

Starting and Operating

In Case of Emergency

Servicing and Maintenance

Quick Links

Chapters

Related Manuals for Jeep Grand Cherokee SRT 2017

Summary of Contents for Jeep Grand Cherokee SRT 2017