1. Manuals
  2. Brands
  3. Advantech Manuals
  4. Handhelds
  5. TREK-753
  6. User manual

Advantech TREK-753 User Manual

7" all-in-one mobile data terminal
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
User Manual
TREK-753
7" All-in-one Mobile Data
Terminal

Advertisement

Table of Contents
loading

Related Manuals for Advantech TREK-753

Summary of Contents for Advantech TREK-753

  • Page 1 User Manual TREK-753 7" All-in-one Mobile Data Terminal...
  • Page 2 No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable. How- ever, Advantech Co., Ltd.

  • Page 3: Declaration Of Conformity

    Consult the dealer or an experienced radio/TV technician for help. Technical Support and Assistance Visit the Advantech web site at http://support.advantech.com where you can find the latest information about the product. Contact your distributor, sales representative, or Advantech's customer service center for technical support if you need additional assistance.

  • Page 4: Packing List

    TREK-753 series Mobile Data Terminal USB/LAN cable clip Warranty card Power cord: DC power inlet cable (200 cm - for TREK-753 only) WWAN or WLAN Antennas (by options) “Drivers, Utilities and User Manual" CD-ROM End User License Agreement (WES and WinCE model), please download driver and related document from http://support.advantech.com...

  • Page 5: Safety Instructions

    The equipment has been dropped and damaged. The equipment has obvious signs of breakage. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and TREK-753 User Manual...
  • Page 6 Transport: carry the unit with both hands and handle with care. Maintenance: to properly maintain and clean the surfaces, use only approved products or clean with a dry applicator. CF/SD/SIM card: Turn off the power before inserting or removing CompactFlash storage cards. TREK-753 User Manual...

  • Page 7: Table Of Contents

    Figure 1.1 TREK-753 dimensions..........5 Chapter System Setup ........7 A Quick Tour of the TREK-753 Mobile Data Terminal ......8 Figure 2.1 Front view of TREK-753 ..........8 Figure 2.2 Rear view of TREK-753..........8 Figure 2.3 Side view of TREK-753 ..........9 Figure 2.4 Bottom view of TREK-753 ..........
  • Page 8 Power Management Utility Program ........... 41 5.4.3 Power Management Parameter Settings........42 Figure 5.10Power management test utility ......... 42 5.4.4 TREK-753 Power Consumption..........42 Execute CAN Demo Utility ..............43 Figure 5.11CAN test ..............43 GPIO Test ....................44 Figure 5.12DI/O test ..............44 Figure 5.13Digital in..............

  • Page 9: Chapter 1 General Information

    Chapter General Information This chapter gives background information on the TREK-753 Mobile Data Terminal. Sections include: Introduction General Specifications Dimensions...

  • Page 10: Introduction

    GbE LAN, and a rich complement of I/O ports (additional COM ports, audio, CAN bus, and J1708). TREK-753 has also been re-engineered to optimize internal space, gained by its full-flat panel touch- screen;...

  • Page 11: General Specifications

    1 x 100/1000-T Gb LAN by RJ45 connecter – 1 x CAN 2.0B with J1939 protocol by High density connector – 1 x J1708 by High density connector – 1 x built-in 2.0w speaker & 1 x built-in microphone in front panel TREK-753 User Manual...
  • Page 12 Operating Temperature : -30° C ~ 60° C – Relative Humidity 95% @ 40° C (No condensing) – Vibration & Shock: MIL-STD-810G (US highway truck), Method 516.5, – SAE J1455, Class 5M3 according DIN EN 60721-3-5 (Lv.2 100G, 6ms, shock) TREK-753 User Manual...

  • Page 13: Dimensions

    1.3 Dimensions Figure 1.1 TREK-753 dimensions TREK-753 User Manual...
  • Page 14 TREK-753 User Manual...

  • Page 15: Chapter 2 System Setup

    Chapter System Setup This chapter details system setup on TREK-753. Sections include: A Quick Tour of the Mobile Data Terminal Installation Procedures Running the BIOS Setup Pro- gram Installing the Drivers for Win XP...

  • Page 16: A Quick Tour Of The Trek-753 Mobile Data Terminal

    2.1 A Quick Tour of the TREK-753 Mobile Data Terminal Before starting to set up the Mobile Data Terminal, take a moment to become familiar with the locations and functions of the controls, drives, connectors and ports, which are illustrated in the figures below. When the Mobile Data Terminal is placed inside truck glove cabinet or under the passenger’s seat next to the driver, its front appears...

  • Page 17: Figure 2.3 Side View Of Trek-753

    Figure 2.3 Side view of TREK-753 Figure 2.4 Bottom view of TREK-753 TREK-753 User Manual...

  • Page 18: Installation Procedures

    2.2 Installation Procedures When you installing TREK-753, the first step will be connect the car power and igni- tion correctly. TREK-753 power cable is designed to connect car battery directly. TREK-753 can be switched ON/OFF by the car ignition signal or its power button both.

  • Page 19: Power Connector

    Orange 2.2.2 Power Connector TREK-753 can be powered on/off by power button or Acc ignition directly. Ignition on/ off will have 5sec (default) delay when power on/off. It can avoid the floating car power supply impact or damage system operation. For more detail of power manage- ment, please see Power mangement in Chapter 5.

  • Page 20: Running The Bios Setup Program

    These files are a very useful supplement to the information in this manual. For more updated driver please refers to Advantech website, www.advantech.com/support The drivers for TREK-753 are listed as below, please just execute the drivers for installation. Device...

  • Page 21: Chapter 3 Hardware & Peripheral Installation

    Chapter Hardware & Peripheral Installation This chapter details the installa- tion of hardware for TREK-753. Sections include: Overview of Hardware Installa- tion and Upgrading Installing the Storage Device and SIM Card Installing System Memory Installing the Drivers for Win XP...

  • Page 22: Overview Of Hardware Installation & Upgrading

    3.2 Installing the Storage Device and SIM Card TREK-753 has a side door and user can install SIM card and storages (CF or SD card) easily. CF card is the main bootable storage which has OS pre-installed from Advantech.

  • Page 23: Installing System Memory

    3.3 Installing System Memory TREK-753 support 200-pin SO DIMM type DDRII DRAM. There's a door can be open for RAM installation.It is very easy to open to install memory. But, we suggest this change performed by our service center to avoid any possible damage (like ESD or wrong position inserted).

  • Page 24: Installing Io Cover

    3.5 Installing IO Cover For TREK-753 whole system IP54 ability, here is a IP54 IO cover kit to mask all the connecters of bottom side. It's a rubber-metal kit includes a rubber cover, a screws mounting frame, batten & batten with boss.
  • Page 25 There're 6 screws holes designed for extra mechanic part installation. The mounting frame needs to be fixed with these holes. Install the cover by 6 screws installed. It will be easy to install rear side first (3 screws) first. TREK-753 User Manual...
  • Page 26 Then install frame with other 3 screws at top side. Insert the batten with boss to the rubber cover. Please place all cables in the right position before another batten fixed in tight. Installation complete. TREK-753 User Manual...

  • Page 27: Installing Wireless Options

    3.6 Installing Wireless options TREK-753 is a highly integrated all-in-one terminal, all wireless options are able to installed at once and works by independent connection. In the standard OS compan- ioned with TREK-753, all the wireless connections have been setup in advance and users will not have to setup again.
  • Page 28 Make sure there is/are wireless router/AP working in same circumstance which TREK-753 is able to connect with. Turn on the TREK-753, booting into OS. Double click the "Setup.exe" in driver CD (WLAN_AW-NE768_090714) to install driver Setup connection Press Start - Control panel - Network connections - Press right button of mouse and select properties in Wireless Network connection, then click "View Available...
  • Page 29 There might have some APs devices appear with different SSID, choice the available one and connect with (might need to input user's ID & password) Click "Connect" to connect with wireless AP. Open the web browser and TREK- 753 will connect to internet. TREK-753 User Manual...

  • Page 30: Gprs

    Make sure the Criterion MC55i GPRS module has install to the TREK-753. Figure 3.2 Top view of TREK-753 Insert the User's SIM card to slot of TREK-753, make sure the User's SIM card has applied the GSM and data transmit/receive service in advance.
  • Page 31 In completing the new connection wizard textbox, select "Add a shortcut to this connection to my desktop", then click Finish. In the Network Connections Panel, press right button of mouse then select properties. In the "Phone number textbox, input:*99***1#, then click Configure. TREK-753 User Manual...
  • Page 32 Change "Maximum speed (bps) to 115200,then click OK. Once complete previous steps, the new connection will be created. Double Click the new connection and Click Button "Dial", then the TREK-753 will connect to the internet. TREK-753 User Manual...

  • Page 33: Hsdpa (3.5G)

    3.6.3 HSDPA (3.5G) Driver installation Make sure the HSDPA module has install to the TREK-753. Figure 3.3 Top view of TREK-753 Insert the User's SIM card to slot, make sure the User's SIM card has applied the 3G service. TREK-753 User Manual...
  • Page 34 Turn on the TREK-753, then booting into OS. Install the HSDPA USB module driver/AP "Watcher_Generic Build 2258.msi" from driver CD into the Windows Embedded OS. Setup connection Check the device manager without any question mark. In completing the new connection wizard textbox, select "Add a shortcut to this connection to my desktop", then click Finish.

  • Page 35: Cdma (3.5G)

    Double Click the "Sierra Wireless Watcher" and Click Button "Connect", then the TREK-753 will connect to the internet. 3.6.4 CDMA (3.5G) Driver installation Make sure the CDMA module has install to the TREK-753. TREK-753 User Manual...
  • Page 36 In completing the new connection wizard textbox, select "Add a shortcut to this connection to my desktop", then click Finish. Once complete previous steps, the new connection will be created. Double Click the on desktop and Click Button "Connect", then the TREK-753 will connect to the internet. TREK-753 User Manual...

  • Page 37: Gps

    3.6.5 GPS Installation Make sure the GPS module & antenna has install to the TREK-753. Figure 3.4 Bottom view of TREK-753 Turn on the TREK-753, booting into OS. Double click the "ublox_A4_U5_USB_drv3264_install_UI.exe" application pro- gram in driver CD and install to TREK-753 OS.
  • Page 38 Install the "u-Center" for setup and test. Start test in "u-Center", setting COM port (COM7) and baud rate (9600bps) use for GPS module. After start test, the NMEA output messages are display on the Development Data View setup connection. TREK-753 User Manual...

  • Page 39: Chapter 4 Pin Assignments

    Chapter Pin Assignments This chapter explains pin assign- ments on the TREK-753.

  • Page 40: Rear Side Connectors

    Power input Acc Ignition Input Note! TREK-753 has 2 power options for different vehicle: Input Voltage 12 V/24 V option support 6~36 V car power design with ISO7637-2 & SAE J1113 compliant (default) 48 V option support 18~58 V input for specific application (Option)

  • Page 41: High Density Connector

    Isolated Relay Driver Output 3# Isolated Relay Driver Output 2# Isolated Relay Driver Output 1# Isolated Dry Contact Input 4 Isolated Dry Contact Input 3 Isolated Dry Contact Input 2 Isolated Dry Contact Input 1 Isolation DIO Ground TREK-753 User Manual...

  • Page 42: Rs-232 Connector (Com8)

    RS-232 RI / +12 VDC (max. 2500 4.5 LED Indicator This system power indicator is an orange LED,controlled by hadrware. This LED will be lit on when the system is in NORMAL mode. When system is off, this LED will be lit off. TREK-753 User Manual...

  • Page 43: Software Demo Utility Setup

    Chapter Software Demo Utility Setup This appendix explains the soft- ware demo utility for TREK-753. Sections include: Introduction How to Set up Demo Utility Installing the Drivers for Win XP...

  • Page 44: Introduction

    5.1 Introduction To make the hardware easier to access for programmers, Advantech has developed a demo utility in order to let customer test the functions on TREK-753. This document describes detailed information for each Advantech demo utility so that application developers can become more familiar with using them.

  • Page 45: Hoy Key Test

    5.2 Hoy Key Test Click "Hot Key test" program in IMC demo main menu. If check "Auto Brightness"; TREK-753 will adjust the panel brightness automatically by build in Light sensor input. Or user can set the brightness of panel and hot key manually.

  • Page 46: Rtc Test

    Key function Definition: Set the parameters to connect to the application program function of the hot key. 5.3 RTC Test Execute “RTC test” For RTC Time setting: You may set year, month, date, and time show as below. Figure 5.4 RTC test - 1 & 2 TREK-753 User Manual...

  • Page 47: Figure 5.5 Rtc Test - 3 &

    Figure 5.5 RTC test - 3 & 4 RTC Alarm Setting: You may also set Alarm time; you may wake up the system by the time you have set. Please refer to the below figure. Figure 5.9 RTC test - 5 TREK-753 User Manual...

  • Page 48: Vehicle Power Management

    1 ~ 18000 seconds LOW_THRESHOLD (12V mode) 11.42 V 10.09 ~ 12.25 V LOW_THRESHOLD (24V mode) 22.44 V 21.11 ~ 23.28 V LOW_DELAY 30 seconds 1 ~ 3600 seconds LOW_ HARD_DELAY 60 seconds 1 ~ 3600 seconds TREK-753 User Manual...

  • Page 49: Power Management Utility Program

    5.4.2 Power Management Utility Program Execute IMCDemo.exe file, see the icon below. TREK-753 User Manual...

  • Page 50: Power Management Parameter Settings

    5.4.3 Power Management Parameter Settings The parameters for power management on TREK-753 could be read or modified by Demo utility (see the image below) or SDK/API. Figure 5.10 Power management test utility 5.4.4 TREK-753 Power Consumption OS: Windows Embedded Standard Burn-in test V6.0...

  • Page 51: Execute Can Demo Utility

    5.5 Execute CAN Demo Utility Figure 5.11 CAN test Reset the module Transmit CAN message Set the polling rate of CAN message reception Received CAN message. Set up the filter of CAN message (only show the message ID) TREK-753 User Manual...

  • Page 52: Gpio Test

    Digital output box to execute the same procedure. See figure 6. Figure 5.12 DI/O test a. Digital Output ==> isolated relay driver output b. Digital Input ==> isolated dry contact input Figure 5.13 Digital in TREK-753 User Manual...

  • Page 53: Video In Test

    There are one video input, please connect camera to the port, CAM1. Choose Chan- nel 1 on [Switch to], then the panel will show the image which camera1 has taken, and it will recover to the same status after 10 sec. Figure 5.15 Video test utility TREK-753 User Manual...

  • Page 54: Audio Test

    5.8 Audio Test TREK-753 has a build-in microphone on front panel, and audio functions (Line out and Line-in & Mic.in) can be extended to remote site by High Density Cable.Both of Line out & Line in function are work directly when High Density cable connected. Mic, in is able to works either front panel or from high density cable.
  • Page 55 Appendix High Density Cable Pin Assignment...

  • Page 56: Standard Usb A Type Female Connecter

    High Density connecter of TREK-753 includes 48 wires in a 2-meter cable. It extends many kinds and numbers IO port with standard type connecters for users. At the host side, it builds a 3M 10150-3000 PE series 50 pin connecter with able to connected with TREK-753.

  • Page 57: Rs-232 Connecter (Db9 Male)

    RS232_DSR RS232_RTS RS232_CTS RS232_RI A.4 4DI /4DO & RS-485 (DB15 male type) Table A.4: 4DI /4DO & RS-485 (DB15 male type) Pin Number Definition ISO_DI1 ISO_DI2 ISO_DI3 ISO_DI4 GND_ISO ISO_DO1 ISO_DO2 ISO_DO3 ISO_DO4 RS485+ RS485- GND(Drain wire) TREK-753 User Manual...

  • Page 58: Can Bus & J1708 (Terminal Block 6P, 5.08Mm Pitch)

    CAN_H (H) CAN_L (L) GND (G) J1708+ (J+) J1708- (J-) GND (G) A.6 Power extension connecter (Terminal Block 3P, 5.08mm pitch) Table A.6: Power extension connecter (Terminal Block 3P, 5.08mm pitch) Pin Number Definition +V12(26AWG) GND(26AWG) +V5(26AWG) TREK-753 User Manual...

  • Page 59: High Density & Connecter Pin List

    DIO & RS-485 RS485- DB15 female RS485+ GND(Drain wire) J1708- J1708+ CAN Bus & J1708 GND(Drain wire) Terminal Block 6P, 5.08mm pitch connecter CAN_L CAN_H +V12(26AWG) +V12(26AWG) Extended Power +V12(26AWG) Terminal Block 3P, 5.08mm GND(26AWG) pitch GND(26AWG) GND(26AWG) TREK-753 User Manual...
  • Page 60 RS232_RI RS232_CTS RS232_RTS RS232_DSR GND(Drain wire) RS-232 male Connecter RS232_DTR RS232_TXD# RS232_RXD# RS232_DCD ISO_DO4 ISO_DO3 ISO_DO2 ISO_DO1 DIO & RS-485 ISO_DI4 DB15 female connecter ISO_DI3 ISO_DI2 ISO_DI1 GND_ISO (26AWG) TREK-753 User Manual...

  • Page 61: Ewf(Enhanced Write Filter)Manager Sop53

    Appendix EWF(Enhanced Write Filter)Manager SOP...

  • Page 62: Ewf(Enhanced Write Filter)Manager Sop

    B.1 EWF(Enhanced Write Filter)Manager SOP Open Start -> All Programs -> Advantech -> Advantech EWF Manager. You will get a user interface as the following picture. A. EWF function: If you want to protect your OS you can use the function. It will recovery your OS after restarting OS.
  • Page 63 C volume. HORM(Hibernate Once and Resume Many): The function can always resume your OS after hibernating, even shutdown or crash. Before using HORM you should set EWF "disable" Check "Enable hibernate" Right-Click on desktop and click "Properties" TREK-753 User Manual...
  • Page 64 Choose "Screen Saver" panel and click "Power”. Check "Enable hibernate". TREK-753 User Manual...
  • Page 65 Activate HORM Open Start -> All Programs -> Advantech -> Advantech EWF Manager. Click "Activate HORM". Chick "OK" to reboot OS. Check "Use the Welcome screen". Open Start -> Control Panel. TREK-753 User Manual...
  • Page 66 Click "Network and Internet Connections". Click "Network Connection". TREK-753 User Manual...
  • Page 67 Right-Click on "Local Area Connection" and click properties. Uninstall "Client Service for NetWare". Click "Yes" to remove "Client Service for NetWare" and reboot OS. Open Start -> Control Panel. TREK-753 User Manual...
  • Page 68 Click "User Accounts" Click "Cancel". Check "Use the Welcome screen" and Click "Apply Options" TREK-753 User Manual...
  • Page 69 Enable EWF Open Start -> All Programs -> Advantech -> Advantech EWF Manager. Click "Enable". Click "OK" to reboot OS. Run "Hibernate" Open Start -> Shut Down When you press "Shift" Standby will become Hibernate TREK-753 User Manual...
  • Page 70 Enable HORM finish VIII You can try to pull power cord after resuming. You will discover the OS always been resuming TREK-753 User Manual...
  • Page 71 TREK-753 User Manual...
  • Page 72 No part of this publication may be reproduced in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permis- sion of the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd. 2011...

Table of Contents