Protection Information (Pi); Levels Of Pi; Setting And Determining The Current Type Level; Identifying A Protection Information Drive - Seagate ST2400MM0129 Product Manual

9.5

Protection Information (PI)

Protection Information is intended as a standardized approach to system level LRC traditionally provided by systems using 520 byte
formatted LBAs. Drives formatted with PI information provide the same, common LBA count (i.e. same capacity point) as non-PI
formatted drives. Sequential performance of a PI drive will be reduced by approximately 1.56% due to the extra overhead of PI being
transferred from the media that is not calculated as part of the data transferred to the host. To determine the full transfer rate of a PI
drive, transfers should be calculated by adding the 8 extra bytes of PI to the transferred LBA length, i.e. 512 + 8 = 520. PI formatted
drives are physically formatted to 520 byte sectors that store 512 bytes of customer data with 8 bytes of Protection Information
appended to it. The advantage of PI is that the Protection Information bits can be managed at the HBA and HBA driver level. Allowing
a system that typically does not support 520 LBA formats to integrate this level of protection.
Protection Information is valid with any supported LBA size. 512 LBA size is used here as common example.
9.5.1

Levels of PI

There are 4 types of Protection Information.
Type 0 - Describes a drive that is not formatted with PI information bytes. This allows for legacy support in non-PI systems.
Type 1 - Provides support of PI protection using 10 and 16 byte commands. The RDPROTECT and WRTPROTECT bits allow for
checking control through the CDB. Eight bytes of Protection Information are transmitted at LBA boundaries across the interface if
RDPROTECT and WRTPROTECT bits are nonzero values. Type 1 does not allow the use of 32 byte commands.
Type 2 - Provides checking control and additional expected fields within the 32 byte CDBs. Eight bytes of Protection Information are
transmitted at LBA boundaries across the interface if RDPROTECT and WRTPROTECT bits are nonzero values. Type 2 does allow the
use of 10 and 16 byte commands with zero values in the RDPROTECT and WRTPROTECT fields. The drive will generate 8 bytes
(e.g.0xFFFF) 8 bytes of Protection Information to be stored on the media, but the 8 bytes will not be transferred to the host during a
read command.
Type 3 - Seagate products do not support Type 3.
9.5.2

Setting and determining the current Type Level

A drive is initialized to a type of PI by using the format command on a PI capable drive. Once a drive is formatted to a PI Type, it may
be queried by a Read Capacity (16) command to report the PI type which it is currently formatted to. PI Types cannot coexist on a
single drive. A drive can only be formatted to a single PI Type. It can be changed at anytime to a new Type but requires a low level
format which destroys all existing data on the drive. No other vehicle for changing the PI type is provided by the T10 SBC3
specification.
Type 1 PI format CDB command: 04 90 00 00 00 00, Write Buffer: 00 A0 00 00
Type 2 PI format CDB command: 04 D0 00 00 00 00, Write Buffer: 00 A0 00 00
9.5.3

Identifying a Protection Information drive

The Standard Inquiry provides a bit to indicate if PI is support by the drive. Vital Product Descriptor (VPD) page 0x86 provides bits to
indicate the PI Types supported and which PI fields the drive supports checking.
For further details with respect to PI, please refer to SCSI Block
Note
Commands - 3 (SBC-3) Draft Standard documentation.
9.6

Seagate RAID Rebuild

Seagate RAID Rebuild is an industry standard feature to enable faster recovery from a failed drive in a RAID configuration. It improves
RAID rebuild performance by extracting easily readable data from a failing drive. It quickly identifies blocks that would take longer to
recover from the failed drive than to rebuild from the remaining drives in the RAID group.
This feature allows host control of error recovery, maximizes up time, and minimizes likelihood of 2nd drive failure in a RAID
configuration.
Seagate Enterprise Performance 10K HDD v9 Product Manual, Rev. D (Draft 2)
™
46