SERVICE MANUAL DVD DIGITAL THEATER SYSTEM MB198 2004 TH-M606,TH-M603 Area suffix J ----------------------------- U.S.A. C -------------------------- Canada (SP-PWM606, (SP-THM606C) (SP-THM606F) (SP-THM606S) SP-PWM603) (XV-THM606, XV-THM603) TABLE OF CONTENTS PRECAUTION............... . . 1-4 SPECIFIC SERVICE INSTRUCTIONS .
Page 2
SPECIFICATION Center unit (XV-THM606/XV-THM603) Audio section Total Harmonic Distortion*1 0.02% Digital input*2 DIGITAL IN (DBS) (OPTICAL): -21 dBm to -15 dBm (660 nm E30 nm) Video section Video System NTSC Horizontal Resolution 500 lines Signal-to-Noise Ratio 64 dB Video output level Composite: 1.0 V(p-p)/75 Ω...
Page 3
Front speakers (SP-THM606F) 5.5 cm (2-3/16 inches) × 2, 3.0cm (1-3/16 inches) Bass-reflex, Magnetically Shielded Speakers Power Handling Capacity 140 W Impedance 4 Ω Frequency Range 95 Hz to 40 kHz Dimensions (W × H × D) 250 mm × 1103 mm × 250 mm (9-7/8 inches × 43-7/16 inches × 9-7/8 inches) Mass 3.67 kg (8.1 lbs) Surround speakers (SP-THM606S)
SECTION 1 PRECAUTION Safety Precautions (1) This design of this product contains special hardware and voltmeter. many circuits and components specially for safety purpos- Move the resistor connection to ea ch exposed metal es. For continued protection, no changes should be made part, particularly any exposed metal part having a return to the original design unless authorized in writing by the path to the chassis, and measure the AC voltage across...
Page 5
Preventing static electricity Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs. 1.5.1 Grounding to prevent damage by static electricity Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as laser products.
Page 6
Importance administering point on the safety F3202 8A-125V F901 F3201 8A-125V 1.6A-125V F101 F3101 10A-125V XV-THM606/XV-THM603 SP-PWM606 SP-PWM603 Caution: For continued protection against risk of fire, replace only with same type 1.6A/125V for F901, 10A/125V for F3101, 6.3A/125V for F101, 8A/125V for F3201,F3202, F153 and F154.
SECTION 3 DISASSEMBLY Main body section 3.1.1 Removing the metal cover (See Figs.1 to 4) (1) From the both sides of th e main body, remove the four screws A attaching the metal cover. (See Figs.1 and 2) Metal cover (2) From the back side of the main body, remove the three screws B attaching the metal cover.
Page 9
3.1.2 Removing the front panel assembly (See Figs.5 and 6) • Prior to performing the following procedures, remove the metal cover. Main board CN456 CN450 CN457 CN460 (1) From the top side of the main body, disconnect the parallel wires from the connectors (CN456, CN457) on the main board.
Page 10
3.1.3 Removing the DVD changer mechanism assembly (See Fig.7) • Prior to performing the following procedures, remove metal cover and front panel assembly. DVD changer mechanism assembly (1) From the top sid e of th e main body, disconnect the ca rd CN402 CN401 CN403 wires from the connectors...
Page 11
3.1.5 Removing the audio & digital input board (See Figs.9 and 10) • Prior to performing the following procedures, remove the metal cover. Main board CN412 Power supply board (1) From the top side of the main body, disconnect the card wires from the connectors (CN411, CN412) on the main Card wires CN411...
Page 12
3.1.8 Removing the main board (See Fig.11) • Prior to performing the following procedures, remove the metal cover, rear panel, audio & digital input board and tuner. CN460 CN456 (1) From the top sid e of th e main body, disconnect the ca rd Earth wire CN457 CN401...
Page 13
Front panel assembly section • Prior to performing the following procedures, remove the metal cover and front panel assembly. 3.2.1 Removing the phone jack board (See Fig.1) (1) From the in side of th e front panel assembly, remove the screw A and screw A' attaching the phone jack board.
Page 14
3.2.5 Removing the power key board (See Fig.4) (1) From the inside of the front panel assembly, remove the two screws E attaching the power key board. Solder poitn g Projection f Front panel assembly Parallel wire Reference: When attaching the power key boa rd, align the proj ec- tions f of the front panel assembly to the holes of the power key board.
Page 15
DVD changer mechanism assembly section • Prior to performing the following procedures, remove the metal cover, front panel assembly and the DVD changer mechanism assembly. 3.3.1 Removing the tray assemblies (See Figs.1 to 5) (1) Remove the two screws A from the top cover and release the two joints a on the both side s of the DVD chan ger Open det lever mechanism assembly.
Page 16
3.3.2 Removing the DVD servo board (See Figs.6 to 8) • Prior to performing the following procedures, remove the tray Short circuit points d assemblies. (1) From the topside of the DVD changer mechanism assem- bly, solder the short-circuit points d on the DVD pi ck up. DVD pickup (See Fig.6) Caution:...
Page 17
3.3.4 Removing the motor board (See Figs.9 and 10) (1) From the top side of the DVD chnager mechanism assem- bly, remove the two belts from the motor pulleys. (See Fig.9) Caution: Take care not to attach grease on the belt. Belt Belt (2) Remove the four scre ws D attaching the motors to the...
Page 18
3.3.7 Removing the DVD pickup (See Figs.12 to 14) • Prior to performing the following procedures, remove the tray Short circuit points i assemblies and DVD traverse mechanism assembly. (1) From the topside of the DVD traverse mechanism assem- DVD traverse mechanism assembly bly, solder the short-circuit points i on the DVD pi ck up.
3.3.9 Removing the spindle motor board (See Figs.15 and 16) • Prior to performing the following procedures, remove the tray Motor base assemblies and DVD traverse mechanism assembly. Card wire (1) From the topside of the DVD traverse mechanism assem- Spindle motor board bly, remove the four screws K attaching the DVD traverse mechanism assembly to the DVD trave rse mechanism...
Page 20
3.3.11 Removing the side (L) assembly and tray switch board (See Figs.19 to 23) • Prior to performing the following procedures, remove the tray Joint tab r assemblies. (1) From the topside of the DVD changer mechanism assem- bly, remove the two screws R attaching the side (L) assem- Side (L) assembly bly.
3.3.12 Removing the side (R) assembly (See Fig.22 to 26) • Prior to performing the following procedures, remove the tray Elevator spring assemblies and DVD servo board. Hook u • When removing the DVD servo board, it is not necessary to re- move the DVD servo board from the bracket.
Page 22
3.3.13 Removing the lifter assembly (See Figs.27 to 31) • Prior to performing the following procedures, remove the tray Hook assembies, DVD servo board, side (L) assembly and side (R) assembly. • When removing the DVD servo board, it is not necessary to re- Joint aa move the DVD servo board from the bracket.
Page 23
3.3.14 Removing the rack holder assembly and sensor assembly (See Figs.32 to 38) • Prior to performing the following procedures, remove the tray assemblies, side (L) assembly, side (R) assembly and lifter as- sembly. Rack holder assembly Reference: If the slide gear of the DVD changer mechanism assembly places at joint ac of the rack holder assembly, turn the gear 1 counterclockwise to move the slide gear in the direction of the Gear 1...
Page 24
Notch ag Sensor assembly Boss af Sensor assembly Sensor slider Joint ae Hole ah Slide gear Boss af Notch ag Joint ae Sensor spring Notch am Fig.35 Pin ak Slot aj Hole ah Slide lever Sensor spring Fig.38 Sensor slider Boss af Sensor spring Fig.36...
Page 25
3.3.15 Taking out the disc in the play mode (See Fig.39 to 42) Reference: Tray assembly Disc Refer to "Removing the tray assemblies". (1) From the topside of the DVD changer mechanism assem- bly, remove the top cover. (2) Unlock the tray assembli es and draw out the tray assem- blies toward the front.
Page 26
Speaker section (For TH-M606) 3.4.1 Removing the amplifier assembly (See Figs.1 to 3) (1) From the back side of the speaker main body, remove Amplifier assembly three screws A attaching the amplifier assembly. (See Fig.1) (2) From the bottom side o f the speaker main body, remove the eight screws B attaching amplifier assembly.
Page 27
3.4.2 Removing the rear panel (See Figs.3 and 4) • Prior to performing the following procedure, remove the ampli- fier assembly. (1) From the back side of the amplifier assembly, remove the five screws C, screw D and screw E attaching the rear pan- el.
Page 28
3.4.6 Removing the power board (See Figs.7 to 9) • Prior to performing the following procedures, remove the am- Barrier plifier assembly, rear panel, heat sink bracket and amplifier board. (1) From the right side of the amplifier assembly, remove the five screws J attaching the power board.
Page 29
3.4.7 Removing the heat sink (See Figs.10 and 11) • Prior to performing the following procedures, remove the am- plifier assembly, rear panel, heat sink bracket, amplifier board and power board. (1) From right side of the amplifier assembly, remove the three screws L and three screws M attaching the heat sink.
Page 30
3.4.9 Removing the LED board (See Fig.13) • Prior to performing the following procedures, remove the am- plifier assembly and rear panel. (1) From the top side of the amplifier assembly, disconnect the wire from the connector CN501 on the LED board. (2) Remove the two screws R attaching the LED board, and take out the LED board.
Page 31
3.4.11 Removing the speaker net (See Figs.15 and 16) (1) From right side of the speaker main body, remove the four screws T attaching the speaker net. (See Fig.15) (2) From bottom side of the speaker main body, insert the tip of the flat-bladed screwdriver or similar tool into the space between the speaker main body and speaker net, and lift the speaker net little by little to remove.
Page 32
3.4.12 Removing the speaker (See Figs.17 and 18) • Prior to performing the following procedure, remove the speak- er net. (1) From right side of the speaker main body, remove the eight screws U attaching the speaker. (See Fig.17) (2) Take out the spe aker from the spe aker main body. (See Fig.18) (3) Disconnect the wires from the terminal of the speaker.
Page 33
Speaker section (For TH-M603) 3.5.1 Removing the amplifier assembly (See Figs.1 to 3) (1) From the back side of the speaker main body, remove two screws A attaching the amplifier assembly. (See Fig.1) (2) From the b ottom side of th e speaker main b ody, remove the eight screws B attaching amplifier assembly.
Page 34
3.5.2 Removing the rear panel (See Figs.4 and 5) • Prior to performing the following procedure, remove the ampli- fier assembly. (1) From the back side of the amplifier assembly, remove the five screws C, screw D and screw E attaching the rear pan- el.
Page 35
3.5.4 Removing the heat sink BKT (See Figs.6 and 7) • Prior to performing the following procedures, remove the am- Amplifer assembly plifier assembly and rear panel. Wire clamp (1) From the left side of the amplifier assembly, remove the wires from the wire clamp on the heat sink BKT.
Page 36
3.5.6 Removing the amp. board (See Fig.10) • Prior to performing the following procedures, remove the am- Amp. board Heat sink plifier assembly, rear panel, heat sink BKT and mother board. (1) From the left side of the amplifier assembly, rem ove the nine screws J attaching the amp.
Page 37
3.5.9 Removing the LED board (See Fig.13) • Prior to performing the following procedures, remove the am- Tie bands plifier assembly and rear panel. (1) From the front side of the amplifier assembly, cut off the tie bands. (2) Remove the screw N attaching the LED board. (3) From the reverse side of the LED board, remove the solder from the solder point b on the LED board.
Page 38
3.5.11 Removing the speaker net (See Figs.16 and 17) (1) From side of the spea ker main body, insert the tip of the Flat-bladed flat-bladed screwdriver or similar tool into the space be- screwdriver,etc. tween the speaker main body and speaker net, and lift the Section c speaker net little by little to remove.
Page 39
3.5.12 Removing the speaker (See Figs.18 and 19) • Prior to performing the following procedure, remove the speak- er net. (1) From right side of the speaker main body, remove the four screws R attaching the speaker. (See Fig.18) (2) Take out the speaker from the speaker main body. (See Fig.19) (3) Disconnect the wires from the terminal of the speaker.
SECTION 4 ADJUSTMENT Test mode setting method (1) Unplug the power plug. (2) Insert power plug into outlet while pressing both "PLAY" key and "STANDBY/ON" key of the main body. "Area code" is indicated at the upper left of display, (3) To release test mode, press "STANDBY/ON"...
Page 41
Normal initialization method Please initialize according to the following procedures in the following case: • Just after you upgrade the firmware. • After you confirm the symptoms that a customer points out. First Initialize, and then confirm whether the symptoms are improved or not.
Page 44
Victor Company of Japan, Limited AV & MULTIMEDIA COMPANY AUDIO/VIDEO SYSTEMS CATEGORY 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan (No.MB198) Printed in Japan...
SCHEMATIC DIAGRAMS DVD DIGITAL THEATER SYSTEM TH-M606,TH-M603 CD-ROM No.SML200406 TH-M606, TH-M603 Area suffix J ----------------------------- U.S.A. C -------------------------- Canada (SP-PWM606, (SP-THM606C) (SP-THM606F) (SP-THM606S) SP-PWM603) (XV-THM606, XV-THM603) Contents Block diagrams 2-5 to 32 Standard schematic diagrams 2-33 to 44 Printed circuit boards No.MB198SCH...
Page 46
In regard with component parts appearing on the silk-screen printed side (parts side) of the PWB diagrams, the parts that are printed over with black such as the resistor ( ), diode ( ) and ICP ( ) or identified by the " " mark nearby are critical for safety.
Block diagrams <Main body section> DVD servo board EXADT0 to 15, EXADR16 to 20 A, B, C, D, E, F, RF+, PD(CD), PD(DVD) IC509 NEXCE, NEXOE, NEXWE DVD traverse LPCO1, LPCO2 FLASH ROM mechanism LD(CD), LD(DVD) CDLDCUR, DVDLDCUR Q101 to Q104 LADD0 to 15 EXADT0 to 15 X351...
Page 49
Audio input/output section SW.P.ON, SETUP SYSTEM C, SW CONN. SL, SR o 15 L, R IC158 IC160 HPOUT_L AMP. Q1131 HPOUT_R Q1133 S_MUTE Q1135 TU-SW S.MUTE +IN 1, +IN 2 IC581 C IN, SW IN IC153 IC591 VOL_MUTE AMP. VOL_DT VOL.
Page 50
<Subwoofer section (For TH-M606)> Terminal section J1002 IC101 FROUT POWER RY101 FLOUT AMP. RY102 COUT IC102 SROUT RY103 POWER SLOUT AMP. IC105 IC104 IC103 Sig.Out AMP. AMP. AMP. FL, FR FL, FR SL, SR C, SR Mini Din SL, SW TX.RX...
Page 51
<Subwoofer section (For TH-M603)> Amplifier section J2702 FLOUT IC201 RY271 POWER FROUT AMP. FCOUT RY272 SLOUT IC202 SROUT POWER RY273 AMP. C, SW IC301 SL, SR AMP. Mini Din L, R AD_L CONN. AD_R IC302 AMP. AD_SL AD_C SW_SIG SR_SIG CN273 CN272 CN271...
Page 52
Standard schematic diagrams <Main body section> Power supply section Parts are safety assurance parts. When replacing those parts make sure to use the specified one.
Page 54
System control section To CN441 To CN442 OF LVA10476-A1 OF LVA104 (SHEET 5) (SHEET 5) To FW521 To FW OF LVA10467-A2 OF LV To CN501 (SHEET 4) (SHEE OF LVA10467-A1 (SHEET 4)
Page 55
To CN442 To CN702 To CN701 OF LVA10476-A1 OF LVA10510-91A OF LVA10510-91A SHEET 5) (SHEET 8) (SHEET 8) Parts are safety assurance parts. When replacing those parts make To FW561 sure to use the specified one. OF LVA10467-A5 (SHEET 4) SHEET 2...
Page 70
<Subwoofer section (For TH-M606)> Terminal section To CN303 To CN201 To CN301 To CN203 (SHEET 11) (SHEET 12) (SHEET 11) (SHEET 12) 2-23...
Page 71
Parts are safety assurance parts. When replacing those parts make N203 To CN302 EET 12) (SHEET 11) sure to use the specified one. SHEET 10 2-24...
Page 72
Mother section To CN133 (SHEET 10) To CN131 (SHEET 10) 2-25...
Page 73
To CN132 (SHEET 10) Parts are safety assurance parts. When replacing those parts make sure to use the specified one. SHEET 11 2-26...
Page 74
Amplifier section To CN121 (SHEET 10) 2-27...
Page 92
Victor Company of Japan, Limited AV & MULTIMEDIA COMPANY AUDIO/VIDEO SYSTEMS CATEGORY 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan Printed in Japan (No.MB198SCH)
DVD mechanism assembly and parts list (Block No.MJ) 3-12 DVD changer mechanism assembly and parts list (Block No.MK) 3-14 Electrical parts list (Block No.01~08) 3-32 Packing materials and accessories parts list (Block No.M3) (TH-M606) 3-34 Packing materials and accessories parts list (Block No.M4) (TH-M603) No.MB198...
Page 94
Exploded view of general assembly and parts list Block No. Powe Operation board Connect board Illumination board Phone jac...
Page 95
Power supply board Main board 54 52 Audio & Digital input board Front board Phone jack board...
Page 96
General Assembly Block No. [M][1][M][M] Symbol No. Part No. Part Name Description Local LV10858-004A FRONT PANEL LV10965-004A(FRONT+INDICATOR+DISC BUTTON) LV21605-001A FL LENS LV34588-002A VOL RING QYSDSF2608Z TAP SCREW M2.6 x 8mm QYSDSF2608Z TAP SCREW M2.6 x 8mm(x3) QYSDSF2608Z TAP SCREW M2.6 x 8mm(x4) LV42851-006A FL SCREEN...
Page 97
Symbol No. Part No. Part Name Description Local QUQH10-2817AJ FFC WIRE LV43657-001A INDICATOR LV21606-001A DISC BUTTON...
Page 98
Speaker assembly and parts list (Subwoofer) (TH-M606) Block No. Amp. board Main board Power board 36 47 LED board...
Page 99
Speaker(Subwoofer) (TH-M606) Block No. [M][6][M][M] Symbol No. Part No. Part Name Description Local LV10880-001A CHASSIS BASE LV30225-0T9A SPACER (x2) LV30225-0U1A SPACER LV30225-0U2A SPACER LV21663-001A HEAT SINK LV21664-001A H.SINK BKT QYSBSG3010E TAP SCREW M3 x 10mm(x3) LV43203-001A SPACER QYSBSG3008E TAP SCREW...
Page 100
Speaker assembly and parts list Block No. (Subwoofer) (TH-M603) Amp. board Mother board LED board...
Page 101
Speaker(Subwoofer) (TH-M603) Block No. [M][7][M][M] Symbol No. Part No. Part Name Description Local LV10875-002A CHASSIS BASE LV30225-0T5A SPACER LV30225-0T6A SPACER LV10876-001A HEAT SINK QYSBSG3010E TAP SCREW M3 x 10mm(x3) LV43691-001A HOLD SPRING LV43203-001A SPACER QYSBSG3010E TAP SCREW M3 x 10mm QYSBSG3016E TAP SCREW M3 x 16mm(x4)
Page 102
DVD mechanism assembly and parts list Block No. FXL-D52-1M Grease =JVG-31N =JVS-1003 3-10...
Page 103
DVD mechanism Block No. [M][J][M][M] Symbol No. Part No. Part Name Description Local LV10751-001A TM CHASSIS LV10752-003A SF MOTOR BASE QAR0308-001 SPINDLE MOTOR LV43461-001A SPECIAL SCREW (x3) QAR0144-003 MOTOR VKS5557-001 F.M. GEAR QYSPSPT2030M SCREW M2 x 3mm LV33985-001A MIDDLE GEAR QYSDST2008Z TAP SCREW M2 x 8mm(x2)
Page 104
DVD changer mechanim assembly and parts list Block No. FMU-SD9-5M Grease =JVG-31N =JVS-1003 CH5-BASE-1M 3-12...
Page 105
DVD changer mechanism Block No. [M][K][M][M] Symbol No. Part No. Part Name Description Local LV10913-001A LOADER ASSY QVY0027-B14 S V RESISTOR QYSDST2004Z SCREW 2mm x 4mm QAR0164-001 MOTOR (x2) LV42340-001A MOTOR PULLEY (x2) LV41431-002A BELT (x2) QYSPSPU1725N SCREW 1.7mm x 2.5mm(x2) LV33965-004A LIFTER ASSY LV33963-001A...
Page 107
Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local C4171 NCB30JK-105X C CAPACITOR 1uF 6.3V K C6501 QETN1HM-475Z E CAPACITOR 4.7uF 50V M C4172 NCB30JK-105X C CAPACITOR 1uF 6.3V K C6502 NCS31HJ-560X C CAPACITOR 56pF 50V J...
Page 108
Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local R4252 NRSA63J-101X MG RESISTOR 100Ω 1/16W J R4932 NRSA63J-222X MG RESISTOR 2.2kΩ 1/16W J R4401 NRSA63J-750X MG RESISTOR 75Ω 1/16W J R4961 QRE141J-271Y C RESISTOR 270Ω...
Page 109
Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local CN407 QGD2504C1-05Z CONNECTOR (1-5) C511 NCB21CK-105X C CAPACITOR 1uF 16V K CN410 QGF1205C1-11 CONNECTOR FFC/FPC (1-11) C541 NCB31HK-103X C CAPACITOR 0.01uF 50V K CN411 QGF1036C1-31 CONNECTOR...
Page 110
Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local IC509 GP1FA352RZ OPT RECEIVER C2540 NCB31CK-104X C CAPACITOR 0.1uF 16V K IC531 RC4580ID-X C2541 QETN1HM-475Z E CAPACITOR 4.7uF 50V M IC581 RC4580ID-X C2542 QETN1HM-475Z E CAPACITOR...
Page 112
Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local D3707 1SS133-T2 DIODE C1210 QFVF1HJ-104Z MF CAPACITOR 0.1uF 50V J D3708 1SS133-T2 DIODE C1211 QFVF1HJ-104Z MF CAPACITOR 0.1uF 50V J D3709 1SS133-T2 DIODE C1212 NCB31HK-152X...
Page 113
Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local C3701 QETN1HM-475Z E CAPACITOR 4.7uF 50V M R1214 QRJ146J-100X UNF C RESISTOR 10Ω 1/4W J C3702 QETN1HM-475Z E CAPACITOR 4.7uF 50V M R1215 NRSA63J-104X MG RESISTOR...
Page 114
Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local R1508 QRZ0224-R22 EMIT RESISTOR 0.22Ω R3721 NRSA63J-104X MG RESISTOR 100kΩ 1/16W J R1509 QRK126J-4R7X UNF C RESISTOR 4.7Ω 1/2W J R3722 NRSA63J-472X MG RESISTOR 4.7kΩ...
Page 115
8.00MHz D2101 MA111-X SI DIODE D2102 MA111-X SI DIODE D2103 MA111-X SI DIODE D2104 1SS244-T2 SI DIODE Subwoofer amp. board (TH-M606) D2105 MA111-X SI DIODE D2106 MA111-X SI DIODE Block No. [0][5][0][0] D2107 1SS244-T2 SI DIODE D2108 MA111-X SI DIODE ...
Page 116
Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local C2111 NCB31HK-102X C CAPACITOR 1000pF 50V K R2026 NRSA63J-273X MG RESISTOR 27kΩ 1/16W J C2112 NCB31HK-102X C CAPACITOR 1000pF 50V K R2027 NRSA63J-472X MG RESISTOR 4.7kΩ...
Page 117
Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local R2230 NRS125J-220X MG RESISTOR 22Ω 1/2W J Q503 KTC3875/YG/-X SI TRANSISTOR R2231 NRS125J-220X MG RESISTOR 22Ω 1/2W J Q504 KTA1504/YG/-X SI TRANSISTOR R2701 NRSA63J-564X MG RESISTOR...
Page 118
Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local D2101 1SS133-T2 DIODE C2305 NDC31HJ-101X C CAPACITOR 100pF 50V J D2201 1SS133-T2 DIODE C2306 NDC31HJ-3R0X C CAPACITOR 3pF 50V J D2301 1SS133-T2 DIODE C2307 NCB21HK-104X...
Page 119
Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local R501 NRSA63J-102X MG RESISTOR 1kΩ 1/16W J R2210 QRK126J-4R7X UNF C RESISTOR 4.7Ω 1/2W J R502 NRSA63J-104X MG RESISTOR 100kΩ 1/16W J R2211 QRJ146J-100X UNF C RESISTOR...
Page 120
Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local R3105 NRSA63J-474X MG RESISTOR 470kΩ 1/16W J R3728 NRSA63J-101X MG RESISTOR 100Ω 1/16W J R3106 NRSA63J-470X MG RESISTOR 47Ω 1/16W J R3729 NRSA63J-473X MG RESISTOR 47kΩ...
Page 121
Symbol No. Part No. Part Name Description Local DVD servo board Block No. [0][8][0][0] C331 NCB31CK-333X C CAPACITOR 0.033uF 16V K Symbol No. Part No. Part Name Description Local C332 NCB31CK-104X C CAPACITOR 0.1uF 16V K C333 NCB31CK-104X C CAPACITOR 0.1uF 16V K C334...
Page 122
Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local R123 NRSA63J-0R0X MG RESISTOR 0Ω 1/16W J R562 NRSA63J-101X MG RESISTOR 100Ω 1/16W J R125 NRSA02J-1R0X MG RESISTOR 1Ω 1/10W J R701 NRSA63J-0R0X MG RESISTOR 0Ω...
Page 124
Packing materials and accessories parts list Block No. (TH-M606) A1, A2, A3, A5, A6 A8,A9,A10, A11,A12 A19,A20,A21 A22, A23 3-32...
Page 125
Packing and Accessories (TH-M606) Block No. [M][3][M][M] Symbol No. Part No. Part Name Description Local LVT1147-001C INST BOOK YU20333 SAFETY INST. BT-51034-2 J=REGIST CARD M606J RM-STHM303J REMOCON UNIT LVT1147-002B INST BOOK M606C BT-52006-2 WARRANTY CARD M606C QAM0588-001 DIN CABLE...
Page 126
Packing materials and accessories parts list Block No. (TH-M603) A1, A2, A3, A5, A6 A8,A9,A10, A11,A12 A19,A20,A21 A22, A23 3-34...
Page 127
Packing and Accessories (TH-M603) Block No. [M][4][M][M] Symbol No. Part No. Part Name Description Local LVT1147-001C INST BOOK YU20333 SAFETY INST. BT-51034-2 J=REGIST CARD M603J RM-STHM303J REMOCON UNIT LVT1147-002B INST BOOK M603C BT-52006-2 WARRANTY CARD M603C QAM0588-001 DIN CABLE QAM0236-001 VIDEO CABLE QMPE090-183-JD...