Page 3 Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Page 4: Fcc Statement
Preface FCC Statement (Federal Communications Commission) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Page 5: Important Safety Instructions
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.
Page 6: Instructions For Care And Operation
Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. Do not expose the computer Do not place it on an unstable Do not place anything heavy...
Page 7 Preface Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work.
Page 8: Power Safety
Preface Power Safety The computer has specific power requirements: • Only use a power adapter approved for use with this computer. • Your AC/DC adapter may be designed for international travel but it still requires a steady, Power Safety uninterrupted power supply. If you are unsure of your local power specifications, consult Warning your service representative or local power company.
Page 9: Battery Precautions
Preface Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Do not remove any batteries from the computer while it is powered on. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
Page 10: Cleaning
Preface Cleaning Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock.
Page 11: Travel Considerations
Preface Travel Considerations Packing As you get ready for your trip, run through this list to make sure the system is ready to go: Check that the battery pack and any spares are fully charged. Power off the computer and peripherals. Close the display panel and make sure it’s latched.
Page 12 Preface On the Road In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind: Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common.
Page 13 Preface Developing Good Work Habits Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints.
Page 14 Preface Lighting Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders. • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. • Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. •...
Page 15: Table Of Contents
Preface Contents Notice .................I Hot Key Buttons & Keyboard ........1-9 FCC Statement .............II Function Keys ..............1-10 Instructions for Care and Operation ......IV System Map: Front & Rear Views .......1-11 Power Safety .............. VI System Map: Left View ..........1-12 Battery Precautions ...........VII System Map: Right View ..........1-13 Cleaning ..............
Page 16 Preface Adding a Printer ............2-11 Drivers & Utilities USB Printer ..............2-11 What to Install ..............4-1 Parallel Printer ............2-11 Module Driver Installation ..........4-1 Service Packs ...............4-3 Power Management Authorized Driver Message .........4-4 Overview ................3-1 Version Conflict Message ...........4-4 Advanced Configuration and Power Interface ....3-1 Updating/Reinstalling Individual Drivers ....4-4 The Power Sources ............3-2 Driver Installation ............4-5...
Page 17 Preface BIOS Utilities Upgrading The Computer Overview ................5-1 Overview ................6-1 The Power-On Self Test (POST) ........5-2 When Not to Upgrade ..........6-2 Failing the POST ............5-3 Removing the Battery ............6-3 Fatal Errors ..............5-3 Upgrading the Hard Disk Drive ........6-5 Non-Fatal Errors ............5-3 Upgrading the Optical (CD/DVD) Device ....6-8 PhoenixBIOS Setup Utility ..........5-4 Upgrading the System Memory (RAM) ......6-10...
Page 18 Preface Troubleshooting Parallel Port ..............A-4 Serial Port ..............A-4 Overview ................8-1 RJ-45 LAN Jack ............A-4 Basic Hints and Tips ............8-2 USB 2.0/1.1 Ports ............A-4 Backup and General Maintenance .........8-3 Viruses ................8-4 Video Driver Controls Upgrading and Adding New Hardware/Software ..8-5 VIA Video Driver Installation ........B-1 Problems and Possible Solutions ........8-7 Advanced Video Controls ..........
Page 19 Preface Keyboard & Pointing Device ........C-3 Interface ................ C-4 Card Reader ..............C-4 PCMCIA ............... C-4 Communication ............. C-4 Power Management ............C-4 Power ................C-4 Environmental Spec ............C-5 Physical Dimensions & Weight ........C-5 Optional ................ C-5 XVII...
Page 20 Preface XVIII...
Page 21: Quick Start Guide
Quick Start Guide Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following: •...
Page 22: Model Differences
Quick Start Guide Model Differences This notebook series includes two different model types (each model includes two design styles). The models differ slightly in design style including the LCD type, and the location of the card reader (the easiest way to dif- ferentiate between the model types is the location of the card reader).
Page 23: Advanced Users
Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “What to Install” on page 4 - “BIOS Utilities” on page 5 - 1 “Upgrading The Computer”...
Page 24: Not Included
Quick Start Guide Not Included Operating Systems (e.g. Windows XP) and applications (e.g. word processing, spreadsheet and database pro- grams) have their own manuals, so please consult the appropriate manuals. System Software Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find this manual refers to the Microsoft Win- dows XP (Home &...
Page 25: System Startup
Quick Start Guide System Startup Remove all packing materials. Place the computer on a stable surface. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports. Attach the AC/DC adapter to the DC-In jack on the right of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter (Note: If you have included the Port Replicator in your purchase option see page 12).
Page 26: System Map: Model A - Top View With Lcd Panel Open
Quick Start Guide System Map: Model A - Top View with LCD Panel Open Optional Built-In PC Camera Wireless Device LED Status Indicators Operation Aboard Hot Key Buttons Aircraft Power Button Keyboard The use of any portable elec- Built-In Microphone tronic transmission devices TouchPad and Buttons aboard aircraft is usually pro-...
Page 27: System Map: Model B - Top View With Lcd Panel Open
Quick Start Guide System Map: Model B - Top View with LCD Panel Open Optional Built-In PC Camera Wireless Device Speaker Operation Aboard LED Status Indicators Aircraft Hot Key Buttons Power Button The use of any portable elec- Keyboard tronic transmission devices TouchPad and Buttons aboard aircraft is usually pro- hibited.
Page 28: Led Indicators
Quick Start Guide LED Indicators Table 1 - 3 - LED Power & Communication Indicators The two sets of LED indicators (LED Status Indica- Icon Color Description tors and LED Power & Communication Indicators) Green The Computer is On on the computer display helpful information about the Blinking The Computer is in Standby current status of the computer.
Page 29: Hot Key Buttons & Keyboard
Quick Start Guide Hot Key Buttons & Keyboard The keyboard has an embedded numerical keypad for easy numeric data input, and features function keys to These buttons give instant access to the functions indi- allow you to change operational features instantly (see cated in the table below.
Page 30 Quick Start Guide Function Keys To use the function keys, press and hold the Fn key, then press the appropriate function key (F1 - F12 etc.). Function Function Function Key Fn + F8 Decrease LCD Brightness Fn + F1 TouchPad Toggle Fn + F9 Increase LCD Brightness Fn + F3...
Page 31: System Map: Front & Rear Views
Quick Start Guide System Map: Front & Rear Views LED Power & Model A - Front Communication Indicators LCD Latch (Model A Only) Model B - Front 7-in-1 Card Reader (Model B Only) External Monitor Port Security Lock Slot Rear Battery Figure 1 - 5 - Front &...
Page 32: System Map: Left View
Quick Start Guide System Map: Left View RJ-45 LAN Jack Model A - Left Vent/Fan Intake 2 * USB 2.0 Ports S/PDIF-Out Jack Line-In Jack PC Card Slot Model B - Left 7-in-1 Card Reader (Model A Only) Figure 1 - 6 - Left View 7-in-1 Card Reader The card reader allows you to use the most popular digital storage card formats: MMC (MultiMedia Card) / SD (Secure Digital) / MS (Memory Stick) / MS Pro (Memory Stick Pro)
Page 33: System Map: Right View
Quick Start Guide System Map: Right View Figure 1 - 7 - Right View Headphone-Out Jack Microphone-In Jack USB 2.0 Port RJ-11 Modem Jack Optical Device Drive Bay (for CD/DVD Device - see page DC-In Jack Changing DVD Regional Codes Go to the Control Panel and double-click System >...
Page 34: System Map: Bottom View
Quick Start Guide System Map: Bottom View Vent/Fan Intake Battery Model A Component Bay Cover Hard Disk Cover The CPU is not a user ser- Speakers viceable part. Opening this compartment, or accessing the CPU at all, may violate your warranty. Model B Overheating To prevent your computer...
Page 35: Windows Xp Start Menu & Control Panel
Quick Start Guide Windows XP Start Menu & Control Panel Most of the control panels, utilities and programs within Windows XP (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop.
Page 36: Video Features
Quick Start Guide Video Features You can switch display devices, and configure display options, from the Display Properties control panel in Windows as long as the video driver is installed. For further information see “Video Driver Controls” on page B - Click Start, point to Settings and click Control Panel (or click Control Panel).
Page 37: Power Management Features
Quick Start Guide Power Management Features The Power Options control panel icon in Windows (see page 15) allows you to configure power management features for your computer. You may conserve power through individual components such as the monitor or hard disk (by means of Power Schemes), or you may use either Stand by or Hibernate mode to conserve power throughout the system (enable Hibernate support from the control panel tab).
Page 38 Quick Start Guide 1 - 18...
Page 39: Features & Components
Features & Components Chapter 2: Features & Components Overview Read this chapter to learn more about the following main features and components of the computer: • Hard Disk Drive • Optical (CD/DVD) Device • 7-in-1 Card Reader • PC Card Slot •...
Page 40: Hard Disk Drive
Features & Components Hard Disk Drive The hard disk drive is used to store your data in the computer. The hard disk can be Power Safety taken out to accommodate other 2.5" parallel (PATA) hard disk drives with a height of 9.5 mm.
Page 41: Optical (Cd/Dvd) Device
Features & Components Optical (CD/DVD) Device There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual de- Sound Volume vice will depend on the module you purchased (see “Storage” on page C - 3). The Adjustment optical device is usually labeled “Drive D:”...
Page 42: Handling Cds Or Dvds
Features & Components Handling CDs or DVDs Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/DVDs can be CD Emergency Eject accessed. If you need to manually eject a CD (e.g.
Page 43: Dvd Regional Codes
Features & Components DVD Regional Codes To change the DVD regional codes see “Changing DVD Regional Codes” on page 1 - DVD Regional Coding Table 2 - 1 Region Geographical Location DVD Regional Coding USA, Canada Western Europe, Japan, South Africa, Middle East &...
Page 44: 7-In-1 Card Reader
Features & Components 7-in-1 Card Reader The card reader allows you to use some of the latest digital storage cards. Push the Card Reader Cover card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s).
Page 45: Pc Card Slot
Features & Components PC Card Slot The computer is equipped with a PCMCIA slot for one type II PC Card. Make sure PC Card Slot Cover you install the PCMCIA/Card Reader driver (see “PCMCIA” on page 4 - Make sure you keep the Inserting and Removing PC Cards cover in the PC Card slot when not in use.
Page 46: Application Hot Key
Features & Components Application Hot Key The hot key buttons give instant access to the default Internet browser and e-mail Application.exe program, and to a user-defined application, with one quick button press. To config- ure a program to open when the application hot key is pressed (Windows Me- You will need to locate dia Player is the default program), follow the instructions below.
Page 47: Touchpad And Buttons/Mouse
Features & Components TouchPad and Buttons/Mouse The TouchPad is an alternative to the mouse; however, you can also add a mouse to Mouse Driver your computer through one of the USB ports. The TouchPad buttons function in much the same way as a two-button mouse. If you are using an ex- ternal mouse your op- erating system may be...
Page 48: Audio Features
Features & Components Audio Features Configure the standard audio options on your computer from the Sounds and Audio Sound Volume Devices control panel in Windows. To access the VIA Audio Deck menu, click Adjustment the VIA Audio Deck icon in the taskbar, or double-click the desktop icon.
Page 49: Adding A Printer
Features & Components Adding a Printer The most commonly used peripheral is a printer. The following conventions will Parallel Printer help you to add a printer, however it is always best to refer to the printer manual for specific instructions and configuration options. After setting up the print- er attach the parallel ca- USB Printer...
Page 50 Features & Components 2 - 12...
Page 51: Power Management
Power Management Chapter 3: Power Management OS Note Overview Power management To conserve power, especially when using the battery, your computer uses the ACPI functions will vary power management system. Power management conserves power by controlling in- slightly depending on dividual components of the computer (the monitor and hard disk drive) or the whole your operating system.
Page 52: The Power Sources
Power Management The Power Sources The computer can be powered by either an AC/DC adapter or a battery pack. Port Replicator AC/DC Adapter AC/DC Adapter You will be provided Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ with AC/DC DC adapter will damage the computer and its components.
Page 53: Turning On The Computer
Power Management Turning on the Computer Now you are ready to begin using your computer. To turn it on simply press the pow- Shutdown er button on the front panel. Note that you should al- When the computer is on, you can use the power button as a Stand by/Hibernate/ ways shut your comput- er down by choosing the Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and...
Page 54: Power Schemes
Power Management Power Schemes You can set your computer to conserve power through individual components by Resuming means of Power Schemes. You can also adjust the settings for each scheme to set Operation the monitor to turn off after a specified time, and the computer's hard disk motor to turn off if the hard disk drive has not been accessed for a specified period of time (if Press a key on the key- the system reads or writes data, the hard disk motor will be turned back on).
Page 55 Power Management Each Windows Power Scheme will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experienc- ing any reduced performance (especially under DC/battery power). Choose the Home/Office Desk scheme for maximum performance when the com- puter is powered from an AC power source.
Page 56: System Power Options
Power Management System Power Options You can use the system power options to stop the computer’s operation and restart where you left off. This system features Stand by and Hibernate sleep mode levels (Hibernate mode will need to be enabled by clicking the option in the Hibernate tab in the Power Options control panel - see “Hibernate”...
Page 57: Stand By
Power Management Stand by Stand by saves the least amount of power, but takes the shortest time to return to full operation. During Stand by the hard disk is turned off, and the CPU is made to idle System Resume at its slowest speed.
Page 58: Configuring The Power Button
Power Management Configuring the Power Button The power button may be set to send the computer in to either Stand by or Hiber- Sleep Button nate mode. In Stand by mode, the LED will blink green. In Hibernate mode the LED will be off (battery) or orange (AC/DC adapter). If you are in a power sav- You may also configure ing mode set to save power through individual components (e.g.
Page 59: Battery Information
Power Management Battery Information Please follow these simple guidelines to get the best use out of your battery. Low Battery New Battery Warning Always completely discharge, then fully charge, a new battery (see “Battery FAQ” When the battery is criti- on page 3 - 12 for instructions on how to do this).
Page 60: Recharging The Battery With The Ac/Dc Adapter
Power Management Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days. Conserving Battery Power We recommend that you do not remove the battery yourself. If you do need to re- move the battery for any reason see “Removing the Battery”...
Page 61: Proper Handling Of The Battery Pack
Power Management Proper handling of the Battery Pack • DO NOT disassemble the battery pack under any circumstances • DO NOT expose the battery to fire or high temperatures, it may explode • DO NOT connect the metal terminals (+, -) to each other Damaged Battery Warning Should you notice any physical defects (e.g.
Page 62: Battery Faq
Power Management Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery. Don’t Caution turn off the computer by yourself even when you see a message that indicates the Danger of explosion if battery is critically low, just let the computer use up all of the battery power and shut battery is incorrectly re-...
Page 63: Drivers & Utilities
Drivers & Utilities Chapter 4: Drivers & Utilities What to Install This chapter deals with installing the drivers and utili- ties essential to the operation or improvement of some The Device Drivers & Utilities + User’s Manual CD- of the computer’s subsystems. The system takes ad- ROM contains the drivers and utilities necessary for vantage of some newer hardware components for the proper operation of the computer.
Page 64 Drivers & Utilities Navigate (Browse..) to D: You will notice that many of the instructions for driver installation require you to “Navigate (Browse) to D:”. We assume that you will install all drivers and utilities from the built-in CD device and it is assigned to “Drive D:”.
Page 65: Service Packs
Drivers & Utilities Service Packs Check the warnings on the following pages regarding installation of the appropriate Service Pack for your Windows XP Service Pack 2 Windows OS. Make sure you have installed the appro- priate Service Pack before installing all the drivers. Make sure you install Windows XP Service Pack 2 (or a Windows XP version which includes Service Pack 2) before installing any drivers.
Page 66: Authorized Driver Message
Drivers & Utilities Authorized Driver Message Updating/Reinstalling Individual Drivers If you receive a message telling you that the driver you If you wish to update/reinstall individual drivers it are installing is not authorized (Digital Signature Not may be necessary to uninstall the original driver.To do Found), just click Yes or Continue Anyway to ignore this go to the Control Panel in the Windows OS and the message and continue the installation procedure.
Page 67: Driver Installation
Drivers & Utilities Driver Installation Check the driver installation order from Table 4 - 1 on page 4 - 6 (all the drivers must be installed in Insert the Device Drivers & Utilities + User’s Manual this order) which is the same as that listed in the CD-ROM and click Install WinXP Drivers (button), Drivers Installer menu below.
Page 68: New Hardware Found
Drivers & Utilities New Hardware Found WinXP SP2 Driver Page # If you see the message “New Hardware Found” (Found New Hardware Wizard) during the in- Install the appropriate WinXP Service Pack Page 4 - 3 stallation procedure (other than when outlined in Chipset Page 4 - 7 the driver install procedure), click Cancel to close...
Page 69: Winxp Driver Installation Procedure
Drivers & Utilities WinXP Driver Installation Procedure Video 1. Click 2.Install Video Driver > Yes. Chipset 1. Click 1.Install Chipset Driver > Yes. Navigate (Browse..) to D:\Drivers\02_Video\setup.exe and click OK. Click Start (menu) > Run... and navigate 2. Click Finish. (Browse..) to Audio D:\Drivers\01_Chipset\SETUP.EXE and...
Page 70: Lan
Drivers & Utilities Modem 1. Click 4.Install LAN Driver > Yes. 1. Click 5.Install Modem Driver > Yes. Click Start (menu) > Run... and navigate Click Start (menu) > Run... and navigate (Browse...) to D:\Drivers\04_LAN\Win- (Browse...) to D:\Drivers\05_Modem\ssetup.exe Setup.exe and click OK. and click OK.
Page 71: Touchpad
Drivers & Utilities TouchPad Hot Key 1. Click 6.Install TouchPad Driver >Yes 1. Click 8.Install Hotkey Driver > Yes. Click Start (menu) > Run... and navigate Click Start (menu) > Run... and navigate (Browse..) to (Browse..) to D:\Drivers\06_Touchpad\Setup.exe and click D:\Drivers\08_Hotkey\Setup.exe and click 2.
Page 72: Wireless Lan
Drivers & Utilities Wireless LAN PC Camera See install procedure in “802.11 b/g WLAN Driver In- See install procedure in “PC Camera Driver Installa- stallation” on page 7 - tion” on page 7 - Bluetooth Port Replicator See install procedure in “Bluetooth Driver Installa- See install procedure in “Port Replicator Serial...
Page 73: Bios Utilities
BIOS Utilities Chapter 5: BIOS Utilities Overview BIOS Settings Warning This chapter gives a brief introduction to the computer’s built-in software: Incorrect settings can cause your system to Diagnostics: The POST (Power-On Self Test) malfunction. To correct mistakes, return to Set- up and restore the Set- Configuration: The PhoenixBIOS Setup Utility up Defaults with <F9>.
Page 74: The Power-On Self Test (Post)
BIOS Utilities The Power-On Self Test (POST) Each time you turn on the computer, the system takes a few seconds to conduct a POST Screen POST, including a quick test of the on-board RAM (memory). 1.BIOS information As the POST proceeds, the computer will tell you if there is anything wrong. If there 2.CPU type is a problem that prevents the system from booting, it will display a system summary 3.Memory status...
Page 75: Failing The Post
BIOS Utilities Failing the POST Errors can be detected during the POST. There are two categories, “fatal” and “non- fatal”. Fatal Errors These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized service center as soon as possible.
Page 76: Phoenixbios Setup Utility
BIOS Utilities PhoenixBIOS Setup Utility The PhoenixBIOS Setup Utility tells the system how to configure itself and man- age basic features and subsystems (e.g. port configuration). Entering Setup To enter PhoenixBIOS Setup Utility, turn on the computer and press F2 during the POST.
Page 77: Setup Screens
BIOS Utilities Setup Screens The following pages contain additional advice on portions of the PhoenixBIOS Setup Utility. Setup Menus Setup menus Along the top of the screen is a menu bar with five (5) menu headings. When you shown in this section are select a heading, a new screen appears.
Page 78: Main Menu
BIOS Utilities Main Menu Figure 5 - 2 PhoenixBIOS Setup Utility Main Menu Main Main Advanced Security Boot Exit Item Specific Help System Time: [14:11:05] System Date: [07/26/2006] IDE Channel 0 Master [MATSHITAUJ-850D-(PM)] <Tab>, <Shift Tab>, or IDE Channel 1 Master [FUJITSU MHV2040AH-(SM)] <Enter>...
Page 79: Ide Channel 0/1 Master (Main Menu)
BIOS Utilities IDE Channel 0/1 Master (Main Menu) Pressing Enter here opens the sub-menu to show the configuration of hard disks and CD/DVD device(s) on the computer’s IDE Channels. Use the Auto (Type:) setting to have the items configured automatically for you. System/Extended Memory (Main Menu) This item contains information on the system memory, and is not user configurable.
Page 80: Advanced Menu
BIOS Utilities Advanced Menu Figure 5 - 3 PhoenixBIOS Setup Utility Advanced Menu Main Advanced Advanced Security Boot Exit Item Specific Help Boot-time Diagnostic Screen: [Enabled] Legacy USB Support: [Enabled] Each Selection Items. Large Disk Access Mode: [DOS] Enable/Disable Installed O/S: [Winxp] integrated devices Reset Configuration Data:...
Page 81: Legacy Usb Support (Advanced Menu)
BIOS Utilities Legacy USB Support (Advanced Menu) Choose “Enabled” if you intend to use USB devices in systems which do not nor- mally support USB functionality (e.g. DOS). The default setting is “Enabled” and does not need to be changed if you intend to use your USB devices in Windows. Large Disk Access Mode (Advanced Menu) Select “Other”...
Page 82: Security Menu
BIOS Utilities Security Menu PhoenixBIOS Setup Utility Security Menu Security Main Advanced S S e e c c u u r r i i t t y y Exit The changes you make Item Specific Help here affect the access to the PhoenixBIOS Set- Supervisor Password Is: Clear...
Page 83: Password On Boot (Security Menu)
BIOS Utilities Password on boot (Security Menu) Specify whether or not a password should be entered to boot the computer. If “En- abled” is selected, only users who enter a correct password can boot the system (see Password Warning the warning in the sidebar). The default setting is “Disabled”. If you set a boot pass- word (Password on boot Note: To clear existing passwords press Enter and type the existing password, then...
Page 84: Boot Menu
BIOS Utilities Boot Menu PhoenixBIOS Setup Utility Figure 5 - 5 Main Advanced Security Exit Boot Boot Menu Item Specific Help Boot priority order: USB FDC: Keys used to view or USB KEY: configure devices: USB HDD: Up and Down arrows IDE 0: MATSHITAUJ-850D-(PM) select a device.
Page 85: Exit Menu
BIOS Utilities Exit Menu Figure 5 - 6 PhoenixBIOS Setup Utility Exit Menu Main Advanced Security Boot Exit Exit Item Specific Help Exit Saving Changes Exit System Setup and Exit Discarding Changes save your changes to Load Setup Defaults CMOS. Discard Changes Save Changes Help...
Page 86 BIOS Utilities 5 - 14...
Page 87: Upgrading The Computer
Upgrading The Computer Chapter 6: Upgrading The Computer Overview Warranty Warning Please check with your This chapter contains information on upgrading the computer. Follow the steps out- service representative lined to make the desired upgrades. If you have any trouble or problems you can con- before undertaking any tact your service representative for further help.
Page 88: When Not To Upgrade
Upgrading The Computer When Not to Upgrade These procedures involve opening the system’s case, adding and sometimes replac- ing parts. Power Safety Warning You should not perform any of these upgrades if: Before you undertake upgrade proce- • Your system is still under warranty or a service contract dures, make sure that •...
Page 89: Removing The Battery
Upgrading The Computer Removing the Battery If you are confident in undertaking upgrade procedures yourself, for safety reasons Warranty Warning it is best to remove the battery. Turn the computer off, and turn it over. Please check with your Slide the latch in the direction of the arrow, and hold it in place.
Page 90 Upgrading The Computer Lift the battery out in the direction of the arrow Figure 6 - 2 Battery Up Lift the battery out. Figure 6 - 3 Battery Out 6 - 4 Removing the Battery...
Page 91: Upgrading The Hard Disk Drive
Upgrading The Computer Upgrading the Hard Disk Drive The hard disk drive can be taken out to accommodate other 2.5" parallel (PATA) HDD System hard disk drives with a height of 9.5mm (h) (see “Storage” on page C - 3). Follow Warning your operating system’s installation instructions, and install all necessary drivers and utilities (as outlined in...
Page 92 Upgrading The Computer For Model A computers (see overleaf for Model B): Slide the hard disk and cover assembly in the direction of arrow Lift the hard disk and cover assembly up in the direction of arrow Remove the hard disk and cover assembly Remove the 4 screws to release the hard disk from the assembly cover, and reverse the process to install any new hard disk.
Page 93 Upgrading The Computer For Model B computers: Remove the cover Pull the tab to slide the hard disk and case assembly in the direction of arrow Lift the hard disk and case assembly out of the bay in the direction of arrow 10.
Page 94: Upgrading The Optical (Cd/Dvd) Device
Upgrading The Computer Upgrading the Optical (CD/DVD) Device Turn off the computer, and turn it over and remove the battery. Remove screws (Model A)/ (Model B), and remove the component bay cover Model A Model B Figure 6 - 7 Removing the Component Bay Cover...
Page 95 Upgrading The Computer Use a screwdriver to carefully push out the optical device at point Reverse the process to install the new device. Figure 6 - 8 Removing the Optical (CD/DVD) Device Upgrading the Optical (CD/DVD) Device 6 - 9...
Page 96: Upgrading The System Memory (Ram)
Upgrading The Computer Upgrading the System Memory (RAM) The computer has two memory sockets for 200 pin Small Outline Dual In-line (SO- DIMM) DDR2 (DDRII) type memory modules (see “Memory” on page C - 2 details of supported module types). The total memory size is automatically detected by the POST routine once you turn on your computer.
Page 97 Upgrading The Computer Gently pull the two release latches on the sides of the memory socket in the direction indicated by the arrows ( & Contact Warning Be careful not to touch the metal pins on the module’s connecting edge. Even the cleanest hands have oils which can attract particles, and degrade the module’s...
Page 98: Upgrading The Processor
Upgrading The Computer Upgrading the Processor If you want to upgrade your computer by replacing the existing processor with a fast- Warranty er/new one you will need to contact your customer service representative. We rec- ommend that you do not do this yourself, since if it is done incorrectly you may The CPU is not a user damage the processor or mainboard.
Page 99: Modules & Options
Modules & Options Chapter 7: Modules & Options Wireless Device Overview Operation Aboard This chapter contains information on the following modules, which may come with Aircraft your computer, depending on the configuration purchased. If you are unsure please The use of any portable contact your service representative.
Page 100: 802.11 B/G Usb Wlan Module
Modules & Options 802.11 b/g USB WLAN Module Before installing the 802.11b/g USB WLAN driver, make sure that the optional Wireless Device Wireless LAN module is on. Use the Fn + F11 key combination (see “Function Operation Aboard Keys” on page 1 - 10) to toggle power to the Wireless LAN module.
Page 101 Modules & Options Network Connection Use the Windows Net- work Connections con- trol panel access available wireless net- works (Start > Settings > Network Connections or Start > Connect To > Show all Connections). Figure 7 - 1 Wireless Network Control Panels 802.11 b/g USB WLAN Module 7 - 3...
Page 102: Bluetooth Module
Modules & Options Bluetooth Module Before installing the Bluetooth driver, make sure that the optional Bluetooth mod- Wireless Device ule is on. Use the Fn + F12 key combination (see “Function Keys” on page 1 - Operation Aboard to toggle power to the Bluetooth module. Make sure you install the drivers in the Aircraft order indicated in Table 4 - 1, on page 4 -...
Page 103 Modules & Options User Guide View the BlueSoleil User Guides from the Help Menu (or press the F1 key) in the IVT Corpora- tion BlueSoleil - Main Window control panel. Click BlueSoleil User Guides in the Contents tab, and click to select the appropriate User Guide from the panel on the right.
Page 104: Pc Camera
Modules & Options PC Camera Before installing the PC Camera driver, make sure that the optional PC Camera is Taking Still Pictures on. Use the Fn + F10 key combination (see “Function Keys” on page 1 - 10) to toggle power to the PC Camera module. Make sure you install the drivers in the Double-click order indicated in Table 4 - 1, on page 4 -...
Page 105: Pc Camera Driver Installation
Modules & Options PC Camera Driver Installation 1. Make sure the module is powered on, and then insert the Device Drivers & Utilities + User’s Manual CD-ROM into the CD/DVD drive. Stand by/Hibernate 2. Click Install Option Drivers. or Shutdown Error 3.
Page 106: Pc Camera Audio Setup
Modules & Options PC Camera Audio Setup If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. Taking Still Pictures Go to the Start menu and point to Settings (or just click Control Panel) and click Double-click Control Panel, then double-click the Sounds &...
Page 107 Modules & Options Figure 7 - 3 Audio Setup PC Camera 7 - 9...
Page 108: Bisoncap
Modules & Options BisonCap BisonCap is a video viewer useful for general purpose video viewing and testing, and can capture video files to .avi format. Pre-Allocating File Space Run the BisonCap application from the Start > Programs/All Programs > Bison- You may pre-allocate the Cam menu (it is recommended that you set the capture file before the capture file size for the capture file...
Page 109: Eliminating Screen Flicker
Modules & Options Eliminating Screen Flicker If you find that the video screen in the BisonCap program is flickering, you can try to adjust the setting in the Video Capture Filter options. Run the BisonCap application. Go to Options and scroll down to select “Video Capture Filter...”. Click either 50Hz or 60Hz under Frequency in Property Page (tab).
Page 110: Port Replicator
Modules & Options Port Replicator If you have included the Port Replicator in your purchase option, the device will al- Port Replicator low you to easily attach the notebook to standard, non-portable devices e.g. a printer AC/DC Adapter or monitor. Note the sidebar warning on the power supply. You will be provided with AC/DC...
Page 111: Port Replicator Setup Instructions
Modules & Options Port Replicator Setup Instructions: Turn the computer OFF. Attach the port replicator’s external monitor cable to the external monitor port at the rear of the computer. Attach the port replicator’s power cable to the DC-In jack on the right of the computer.
Page 112: Port Replicator Network (Lan) Driver (Winxp)
Modules & Options Port Replicator Network (LAN) Driver (WinXP) 1. Attach the port replicator as per the instructions in “Port Replicator Setup Instructions:” on page 7 - 13 2. Insert the provided port replicator CD into the computer’s CD/DVD drive. 3.
Page 113: Troubleshooting
Troubleshooting Chapter 8: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
Page 114: Basic Hints And Tips
Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer ap- pears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working.
Page 115: Backup And General Maintenance
Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wal- let.
Page 116: Viruses
Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the defini- tions file updates are usually downloadable directly from the internet.
Page 117: Upgrading And Adding New Hardware/Software
Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing.
Page 118 Troubleshooting • Thoroughly check any recent changes you made to your system as these changes may affect one or more system components, or software programs. If possible, go back and undo the change you just made and see if the problem still occurs. •...
Page 119: Problems And Possible Solutions
Troubleshooting Problems and Possible Solutions Problem Possible Cause - Solution You turned on the power Battery missing / incorrectly installed. Check the battery bay, make sure the battery is present and but it doesn’t work. seated properly (the design of the battery only allows it to go in one way). Make sure there’s nothing interfering with the battery contacts.
Page 120 Troubleshooting Problem Possible Cause - Solution The computer feels too Make sure the computer is properly ventilated and the Vent/Fan intakes are not blocked. If this hot. doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface (see “Overheating”...
Page 121 Troubleshooting Problem Possible Cause - Solution Nothing appears The system is in a power saving mode. Toggle the sleep/resume key combination, Fn + F4 (see screen. “Sleep Button” on page 3 - The screen controls need to be adjusted. Toggle the screen control key combinations Fn + F8/F9. If you’re connected to an external monitor, make sure it’s plugged in and turned on.
Page 122 Troubleshooting Problem Possible Cause - Solution The sound cannot be The volume might be set too low. Check the volume control in the Volume Control Panel in the heard or the volume is Windows taskbar, or use the key combination Fn + F5 and F6 (see “Audio Features”...
Page 123 Troubleshooting Problem Possible Cause - Solution The system freezes or The system’s power saving features have timed-out. Use the AC/DC adapter, press the sleep (Fn the screen goes dark. + F4) key combination, or press the power button if no LEDs are lit. The system never goes Power Options features are not enabled.
Page 124 Troubleshooting 8 - 12...
Page 125: Interface (Ports & Jacks)
Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc. Interface (Ports & Jacks) A - 1...
Page 126: Notebook Ports And Jacks
Interface (Ports & Jacks) Notebook Ports and Jacks Item Description Card Reader Port The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device. DC-In Jack Plug the supplied AC/DC adapter into this jack to power your computer.
Page 127: Rj-11 Modem Jack
Interface (Ports & Jacks) Item Description RJ-11 Modem Jack This port connects to the built-in modem. You may plug the telephone line directly into this RJ-11 telephone connection. Note: Broadband (e.g. ADSL) modems usually connect to the LAN port. RJ-45 LAN Jack This port supports LAN (Network) functions.
Page 128: Optional Port Replicator Ports And Jacks
Interface (Ports & Jacks) Optional Port Replicator Ports and Jacks Item Description DC-In Jack Plug the supplied AC/DC adapter into this jack to power your computer. External Monitor (VGA) This port allows you to connect an external monitor, or Flat Panel Display, to get dual video or Port simultaneous display on the LCD and external monitor/FPD (see “Display Devices”...
Page 129: Video Driver Controls
Video Driver Controls Appendix B: Video Driver Controls The basic settings for configuring the LCD are outlined in “Video Features” on page 1 - VIA Video Driver Installation Make sure you install all the drivers in the order indicated in Table 4 - 1, on page 4 6.
Page 130: Advanced Video Controls
Video Driver Controls Advanced Video Controls This section is about making adjustments for the LCD, and switching display devic- Function Key es. The basic settings for configuring the LCD are outlined in “Video Features” on Combination page 1 - You can use the Fn + F7 key combination to Video Driver Controls toggle through the dis-...
Page 131: S3Tray Plus Utility
Video Driver Controls S3Tray Plus Utility The S3Tray Plus utility will appear in the taskbar when the video driver is installed. Click/Right-click the icon to bring up the menu below. From this menu you will also be able to make display adjustments, access the Display Properties control pan- el, check video memory information etc.
Page 132: S3 Display Control Panels
Video Driver Controls S3 Display Control Panels Right-click the S3Tray Plus utility in the taskbar to bring up the menu for the individual control panels, or access the menus from the Advanced tab in the Display Help Menus Properties control panel. Right-click on almost any item in the tabs to bring up the “What’s...
Page 133: Display Devices
Video Driver Controls Display Devices Besides the built-in LCD, you can also use an external monitor (CRT)/flat panel dis- S3Tray Plus Utility play as your display device. Connect it to the external monitor port on the right of the computer. See the instructions below: You can also use the S3Tray Plus utility in the taskbar to config-...
Page 134: Display Modes
Video Driver Controls Display Modes Single Display Playing DVD Videos Only one of your attached displays is used. If you want to play a DVD video in a multiple Multiple Monitors monitor mode, then This display mode simply shows an exact copy of the Primary display desktop on choose EITHER the Secondary display(s).
Page 135 Video Driver Controls To Enable Extended Desktop (Display Properties) Attach the external display to the external monitor port and turn it on. Go to the Display Properties control panel (see “Video Features” on page 1 - Display Settings and click Settings (tab). Extended Desktop Click the monitor icon (e.g.
Page 136 Video Driver Controls B - 8...
Page 137: Specifications
Specifications Appendix C: Specifications Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/ speeds and CD/DVD device types) may be changed or updated due to the manufacturer's release schedule. Check with your service center for details.
Page 138: Processor
Specifications Feature Specification Processor Intel® Core™ Duo Processor 65nm (65 Nanometer) Process Technology (478-pin) Micro-FC-PGA Package 2MB On-die L2 Cache & 667MHz FSB T2300/ T2400/ T2500/ T2600/ T2700 1.66/ 1.83/ 2.0/ 2.16/ 2.33 GHz Intel® Core™ Solo Processor 65nm (65 Nanometer) Process Technology (478-pin) Micro-FC-PGA Package 2MB On-die L2 Cache &...
Page 139: Lcd
Specifications Feature Specification Model A Computers: Model B Computers: 15.0" XGA (1024*768) Flat Panel TFT 14.0" WXGA (1280*768) Flat Panel TFT 15.0" XGA (1024*768) Glare Type Flat Panel TFT 14.0" WXGA (1280*768) Glare Type Flat Panel TFT Video Adapter VIA VN800 Integration Unichrome Pro 3D/2D Graphics Shared Memory Architecture of up to 64MB of Dynamically Allocated Video Memory Supports Analog Monitor Pixel Resolution up to 1600 * 1200...
Page 140: Interface
Specifications Feature Specification Interface Three USB 2.0 Ports One S/PDIF Output Jack (5.1CH) One External Monitor Port One RJ-11 Modem Jack One Headphone-Out Jack One RJ-45 LAN Jack One Microphone-In Jack One DC-in Jack One Line-In Jack Card Reader Embedded 7-in-1 Card Reader (MS/ MS Pro/ SD/ Mini SD/ MMC/ RS MMC/ MS Duo) Note: MS Duo/ Mini SD/ RS MMC Cards require a PC adapter PCMCIA One Type-II PCMCIA CardBus PC Card Slot...
Page 141: Optional
Specifications Feature Specification Environmental Temperature Relative Humidity Spec Operating: 5°C ~ 35°C Operating: 20% ~ 80% Non-Operating: -20°C ~ 60°C Non-Operating: 10% ~ 90% Physical Model A Computers: Model B Computers: Dimensions & 333mm (w) * 276mm (d) * 24-33mm (h) 333mm (w) * 243mm (d) * 24-33mm (h) Weight 2.6 kg With 6 Cell Battery...
Page 142 Specifications C - 6...

Clevo M540S User Manual

Quick Start Guide

Features & Components

Power Management

Drivers & Utilities

BIOS Utilities

Upgrading the Computer

Modules & Options

Troubleshooting

Interface (Ports & Jacks)

Video Driver Controls

Specifications

Quick Links

Related Manuals for Clevo M540S

Summary of Contents for Clevo M540S

Table of Contents