Related Manuals for Lagler SINGLE
Summary of Contents for Lagler SINGLE
- Page 1 SINGLE - THE SINGLE-DISC SANDING MACHINE Operation, Maintenance, Safety Translation of the original operating instructions for the single-disc sanding machine SINGLE...
- Page 2 Handle with stepless adjustment of the guide tube Cable holder Guide tube Drive motor Control cable connector Motor cover Wheel Dust extraction socket with cap Rubber buffer Sanding plate Fig. 1 Assemblies of the SINGLE single-disc sanding machine SINGLE 01.02.2013 English / Englisch...
-
Page 3: Table Of Contents
Preparing the machine for operation ...........................8 Connecting the mains cable ............................9 Starting the machine ..............................9 Switching off the machine ............................10 Working with the SINGLE ............................11 General application tips ............................... 11 Changing the sanding plate ............................11 Changing the sanding disc ............................12 Adjusting and replacing the cable holder ........................ -
Page 4: Introduction
SINGLE and will be able to provide any The SINGLE single-disc sanding machine is intended for dry use assistance you may need. only. Never attempt to use the SINGLE for any type of wet operation (risk of fatal accidents)! 1.3 INTENDED USE OF THE MACHINE... -
Page 5: Danger Warnings
(please see Section 3.3, Starting the machine). Use only tools, accessories and spares intended for the SINGLE and ® supplied by LÄGLER . No warranty cover exists for parts sourced from other manufacturers. -
Page 6: Safety Devices
= Protection from live parts Technical data Manufacturer ............Eugen Lägler GmbH Note on noise emission: Machine type ........Single-disc sanding machine The specified values are emission values Serial number ............. see rating plate and are not required to constitute safe Year of construction ........... - Page 7 Replace screw for attaching paper disc if worn or damaged • Replace wheels if worn or damaged • Replace extension cable if damaged • Replace motor cable if damaged • Replace buffer if damaged • Replace fluffy sealing strip if damaged SINGLE 01.02.2013 English / Englisch...
-
Page 8: Getting Started
GETTING STARTED Getting started This section describes the procedure for commissioning the SINGLE on site. In order to exclude the possibility of damage and malfunc- tions, it is essential to proceed in the sequence outlined below. Before working with the machine for the first time, operating staff must be adequately instructed. -
Page 9: Connecting The Mains Cable
GETTING STARTED The height of the guide tube can be adjusted, allowing you to work with the SINGLE as comfortably as possible. To make this adjustment, pull the adjusting lever towards you (Fig. 3). This releases the lock on the guide tube so that it can be moved up or down. -
Page 10: Switching Off The Machine
• the dust extraction socket is closed either with its cap or with a vacuum cleaner hose! When you have made these checks, the SINGLE can be started! Fig. 9 Never switch on the machine unless there is a Pull both the start levers AT THE SAME TIME and hold the handle sanding plate mounted! tight with both hands (Fig. -
Page 11: Working With The Single
WORKING WITH THE SINGLE Working with the SINGLE 4.1 GENERAL APPLICATION TIPS It is possible to avoid leaving deep sanding tracks caused by exces- sively coarse abrasion grain size by initially selecting a fine grain size for the first sanding process. -
Page 12: Changing The Sanding Disc
WORKING WITH THE SINGLE Release the adjusting lever so that the guide tube can engage again. Carefully tilt the machine backwards on the wheels. As you do so, steady the machine with your foot to stop it roll- ing away (Fig. 14). Please ensure that the machine is stable... - Page 13 WORKING WITH THE SINGLE Carefully tilt the machine back up over the wheels and onto the sanding plate. As you do so, steady the machine with your foot to stop it rolling away (Fig. 16). 4.3.2 CHANGING CONVENTIONAL SANDING DISCS...
-
Page 14: Adjusting And Replacing The Cable Holder
Please comply with the safety specifications made by the vacuum cleaner manufacturer and read through the operating instructions for the vacuum cleaner carefully! Plug the mains plug of the SINGLE into the extension cable. Plug the extension cable plug into the socket on the vacuum cleaner (Fig. 23). -
Page 15: Attaching The Fluffy Sealing Strip As Protection Against Dust
To make work easier, you can attach the extension cable to the Fig. 24 Open the cap and attach the hose to the SINGLE. suction hose of the vacuum cleaner with several cable binders. In this way you can ensure that the cable will not get caught up under the machine (Fig. -
Page 16: Transport And Storage
Also, when the machine is out of use for extended periods, you should place the machine on the bottom part of the transport packaging in which it is delivered. SINGLE 01.02.2013 English / Englisch... -
Page 17: Maintenance And Replacement Of Wearing Parts
(Fig. 31). SINGLE 01.02.2013 English / Englisch... - Page 18 Remove the shock absorber (Fig. 33). Replace the parts that are damaged or worn. The gear of the SINGLE is maintenance-free and contains a special oil. The incorrect volume of oil can cause severe Fig. 32 Release the adjusting lever and carefully tilt the damage to the gear.
-
Page 19: Replacing The Wheels
6.4 REPLACING THE CENTERING DOME ON THE SANDING PLATE Remove the sanding plate from the SINGLE and lay it on the floor with the flat side down. Turn the centering dome clockwise out of the sanding plate with an open-ended or ring spanner (LEFT-HANDED THREAD, Fig. -
Page 20: Regular Maintenance And Testing In Accordance With Accident Prevention Regulations
(please see the rating plate). If you do not do this, the service passport is invalid. Ensure that maintenance work is recorded in the service passport by completing the relevant box with date, stamp and signature. SINGLE 01.02.2013 English / Englisch... -
Page 21: Troubleshooting
Have the motor cable and are very familiar with the SINGLE and will the extension cable been disconnected from each other?). be able to provide any assistance you may •... -
Page 22: General Safety Remarks
Guard against electric shocks Avoid physical contact with earthed components such as pipes, radiators, stoves and fridges. Use the DI safety plug (For part nos. please see Section 11, Spare parts). SINGLE 01.02.2013 English / Englisch... - Page 23 Pull the plug out of the socket When the machine is not in use, before performing maintenance work and when changing tools, the mains plug must be pulled out of the socket. SINGLE 01.02.2013 English / Englisch...
- Page 24 Damaged switches must be replaced by an after-sales workshop. Never use machines with switches which cannot be turned on or off. SINGLE 01.02.2013 English / Englisch...
- Page 25 NOTES SINGLE 01.02.2013 English / Englisch...
-
Page 26: Circuit Diagrams
230 V / 60 CPS Hi = A uxiliary winding 01.09.2006 1.2 kW / 230 V / 50 CPS SINGLE: S ingle-phase AC motor 1.2 kW / 230 V / 60 CPS EUGEN LÄGLER GMBH Phone: 0049 - 7135 - 98 90 - 0 E-mail: info@laegler.com... - Page 27 Correct rotating direction of the motor: Look to the gear unit Look to the fan wheel 01.06.2008 SINGLE: Three -phase AC motor 1.6 kW / 400 V / 50 CPS EUGEN LÄGLER GMBH Phone: 0049 - 7135 - 98 90 - 0 E-mail: info@laegler.com...
-
Page 28: Spare Parts
SPARE PARTS SINGLE 01.02.2013 English / Englisch... - Page 29 SPARE PARTS Item Part number Description 850.01.80.200 Dust extraction socket 000.65.43.252 Motor cable 3 x 2.5 mm² 000.65.71.040 Integrated socket 7500.1003.010 Screw 850.05.09.105 Wheel 0125.1012.000 Washer 0471.0012.000 Circlip 850.01.02.105 Buffer 850.01.40.100 Velcro 850.01.51.100 Fluffy sealing strip SINGLE 01.02.2013 English / Englisch...
- Page 30 SPARE PARTS SINGLE 01.02.2013 English / Englisch...
- Page 31 SPARE PARTS Item Part number Description 0912.1006.016 Screw 0125.1006.000 Washer 850.20.28.105 Cable holder 850.20.29.100 Sliding block 7984.1008.030 Screw 900.70.25.105 Bumper felt SINGLE 01.02.2013 English / Englisch...
- Page 32 SPARE PARTS SINGLE 01.02.2013 English / Englisch...
- Page 33 Contactor 000.65.20.230 Relay 850.64.06.100 Adapter mounting 850.64.07.205 Shock absorber 850.64.08.100 Plate mounting 1481.0006.032 Spring type straight pin 6797.1008.000 Washer 7984.1008.030 Screw 9021.1005.000 Washer 7500.1005.012 Screw 850.65.80.100 Control electric system complete, 230 V / 50 Hz SINGLE 01.02.2013 English / Englisch...
- Page 34 SPARE PARTS SINGLE 01.02.2013 English / Englisch...
- Page 35 SPARE PARTS Item Part number Description 850.02.10.100 Sanding plate SINGLE complete 850.02.06.200 Centering dome 850.02.11.100 Velcro coating, for pad and Velcro sanding disc (two parts necessary) 850.02.13.105 Velcro ring flexible 850.02.05.100 Paper tensioning disc 7991.1010.725 Screw, left-handed thread SINGLE 01.02.2013...
- Page 36 SPARE PARTS SINGLE 01.02.2013 English / Englisch...
- Page 37 Extension cable 3 x 2.5 mm², 10 m long 000.01.20.010 Respiratory protection mask P3 701.10.00.100 Impact tool 702.00.00.200 Parquet layer tool ZUGEISEN, small 703.00.00.200 Parquet layer tool ZUGEISEN, broad 000.01.65.020 Safety switch PRCD-S (for German mains supply) 850.80.10.105 Additional weight SINGLE SINGLE 01.02.2013 English / Englisch...
- Page 38 NOTES SINGLE 01.02.2013 English / Englisch...
-
Page 39: Service Passport
Signature and company stamp Signature and company stamp Date of test and Date of test and Date of test and maintenance work: maintenance work: maintenance work: Signature and company stamp Signature and company stamp Signature and company stamp SINGLE 01.02.2013 English / Englisch... -
Page 40: Eu Declaration Of Conformity
SINGLE Serial number: See type plate Commercial name: Single-disc sanding machine fulfils all the relevant provisions of the specified above European Directive. The machine also fulfils all the relevant provisions of the European Directive Electromagnetic compatibility (2004/108/EG). The following harmonized standards have been applied:...