Advertisement
Quick Links
INSTALLATION INSTRUCTIONS
For Sharp Built-in Kit Models RK-94S27 or RK-94S30
THIS KIT IS UL APPROVED TO ALLOW CERTAIN MICROWAVE OVENS TO BE INSTALLED
ABOVE ANY ELECTRIC WALL OVEN. PLEASE SEE THE OPERATION MANUAL
REGARDING APPROVED BUILT-IN APPLICATIONS.
IMPORTANT:
This Built-in Kit is designed for and approved only for those Sharp
Microwave Ovens specifying Built-In Kit RK-94S27 or RK-94S30.
Refer to operation manual for approved models or www.sharpusa.
com\trimkits
PLEASE READ THESE INSTRUCTIONS THOROUGHLY BEFORE
BEGINNING INSTALLATION!
• Always DISCONNECT THE PLUG of the microwave oven from the
electrical outlet before installing the Built-in Kit. Remove the Carou-
sel turntable from the oven cavity.
• Because the kit includes metal parts, due caution should be used
in handling and installation to avoid the possibility of injury.
A
DUCT (A)-1
B
DUCT (A)-2
C
DUCT (A)-3
D
DUCT (B)
E
DUCT (C)
F
G
H
I
J
K
L
ITEM
A
DUCT (A)-1
PDUC-0259WRW0
B
DUCT (A)-2
PDUC-B127MRP0
C
DUCT (A)-3
PDUC-A734WRW0
D
DUCT (B)
PDUC-0260WRW0
E
DUCT (C)
PDUC-A274WRW0
F
BOTTOM DUCT ASSEMBLY
FDUC-B099MRK1A
G
M3.9-16MM PAN HEAD TAPPING
SCREW, ZINC
XOPS740P16000
H
WOOD SCREW
XTSS740P20000
I
CABINET SCREW/ CLEAR
XOTS740P12000
J
FRONT FRAME
RK-94S27: FDECAB229MRK0
RK-94S30: FDECAB227MRK0
K
BACK FRAME
RK-94S27: FDECAB230MRK0
RK-94S30: FDECAB226MRK0
L
CUSHION SHEET
PCUSGB059MRP0
Check list for parts when unpacking. Note J. Front
Frame and K. Back Frame are shipped attached.
Snap apart before installation.
1
PART NAME
QTY
1
1
1
1
1
1
4
2
10
1
1
1
E
Advertisement
Related Manuals for Sharp RK-94S27
Summary of Contents for Sharp RK-94S27
- Page 1 ABOVE ANY ELECTRIC WALL OVEN. PLEASE SEE THE OPERATION MANUAL REGARDING APPROVED BUILT-IN APPLICATIONS. IMPORTANT: This Built-in Kit is designed for and approved only for those Sharp Microwave Ovens specifying Built-In Kit RK-94S27 or RK-94S30. Refer to operation manual for approved models or www.sharpusa.
- Page 2 The opening in the wall or cabinet must be within the following dimensions, centered horizontal to the cabinet. FLOOR RK-94S27 RK-94S30 20" 20" 26-7/8" 29-7/8"...
- Page 3 E. Carefully turn over exhaust assembly. Remove adhesive F. Remove SCREW from the upper right and left corners at backing from CUSHION L. The cushion should be applied the rear of the oven. Place duct assembly on the top of to the flanges of the duct assembly as indicated by the unit as shown and secure the duct assembly to the arrows.
- Page 4 USA please call Sharp’s Customer Assistance Center at 1-800-BE-SHARP (1-800-237-4277) In Canada, call 905-568-7140 SHARP ELECTRONICS CORPORATION 1 Sharp Plaza Suite 1, Mahwah, New Jersey 07495-1123, U.S.A. SHARP ELECTRONICS OF CANADA LTD. 335 Britannia Road East Mississauga, Ontario L4Z 1W9, Canada...