Advertisement
Quick Links
Download this manual
See also:
Instruction Manual
INDEX
Page
Contents
2
3
4
5
7
17
18
19
SPHERISCAN
SPHERILIGHT
INSTRUCTION MANUAL
Congratulations on choosing a Clay Paky product
We thank you for your custom.
Please note that this product, as all the others in the rich Clay
Paky range, has been designed and made with total quality to
ensure excellent performance and best meet your expectations
and requirements.
1
C11260
C11270
Advertisement
Related Manuals for Clay Paky C11260
Summary of Contents for Clay Paky C11260
-
Page 1: Table Of Contents
C11260 SPHERISCAN C11270 SPHERILIGHT INSTRUCTION MANUAL INDEX Congratulations on choosing a Clay Paky product Page Contents We thank you for your custom. Please note that this product, as all the others in the rich Clay Safety Information Paky range, has been designed and made with total quality to... -
Page 2: Safety Information
SAFETY INFORMATION SAFETY INFORMATION IMPORTANT: Clay Paky recommends you carefully read and keep the safety information on this product, also http://www.claypaky.it/en available in digital format at the following link: Ref: [FIS00M – Safety Information Spheriscan - Spherilight] INFORMAZIONI DI SICUREZZA... -
Page 3: Unpacking And Preparation
UNPACKING AND PREPARATION LAM00D Packing contents - Fig. 1 Installing the projector - Fig. 2 WARNING: with the exception of when the projector is positioned on the floor, the safety cable must be fitted. (Cod. 105041/001 available on request). The projector can be installed on the floor resting, on a truss or on the ceiling or wall. This must be securely fixed to the support structure of the projector and then connected to the fixing point as shown on the pictures above. -
Page 4: Installation And Start-Up
INSTALLATION AND START-UP Connecting and disconnecting power cable - Fig. 3 SPHERISCAN SPHERILIGHT... -
Page 5: Control Panel
CONTROL PANEL Mains Connecting to the mains supply - Fig. 4 Connecting to the control signal line (DMX) - Fig. 5 Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ohm characteristic impedance, 22-24 AWG, low capacity. Do not use microphone cable or other cable with characteristics differing from those specified. - Page 6 Reversal of the display - Fig. 7 To activate this function, press UP and DOWN keys simultaneously while the display is in the rest mode. This status will be memorised and Setting the projector starting address maintained even for the next time it will be switched on. To return to the initial state, repeat the operation all over again. On each projector, the starting address must be set for the control signal (addresses from 1 to 512).
-
Page 7: Maintenance
MAINTENANCE Opening the covers - Fig. 8. Continue SPHERISCAN SPHERILIGHT... - Page 8 Fan assembly removal - Fig. 9. SPHERISCAN SPHERILIGHT...
- Page 9 Fan /Driver assembly removal - Fig. 10. Continue SPHERISCAN SPHERILIGHT...
- Page 10 • General cleaning of internal parts. • Restoring lubrication of all parts subject to friction, using lubricants specifically supplied by Clay Paky. • General visual check of the internal components, cabling, mechanical parts, etc.
- Page 11 Cleaning of the filters - Fig. 12. Continue SPHERISCAN SPHERILIGHT...
- Page 12 Opening and closing lamp compartment - Fig. 13 Lamp change - Fig 14 WARNING: do not touch the lamp’s envelope with bare hands. Should this happen, clean the bulb with a cloth soaked in alcohol and dry it Take the new lamp out of its package and insert in the fitting. with a clean, dry cloth.
- Page 13 Rotating gobo wheel Fig. 16. ATTENTION: - Before use custom gobos contact Clay Paky; - The original gobos have a special coating designed specifically to resist to the high temperatures; - The rotating gobo wheel only use dichroic glass gobos (it is not possible to use metal gobos);...
- Page 14 C21090 (21.65") ±0,3 (17.72") (6.38") (15.35") (3.15") (18.50") ±0,5 (20.55") Installation under the stage - Fig. 17. To install the projector under the stage, it is suggested to remove the main bracket and mount the two handles (part number C21090) that allow you to drop easily the projector.
- Page 15 0° ÷ +45° 0° ÷ -45° 180° 180° 180° 180° 180° How to fit the fans covers - Fig. 18. Depending on how the projector is installed, the covers fan must be positioned so that in case of rain, the water flows in the correct way. Continue SPHERISCAN SPHERILIGHT...
- Page 16 Battery removal - Fig. 19 This product contains a rechargeable lithium iron tetraphosphate battery. To preserve the environment, please dispose the battery at the end of its life according to the regulation in force. LiFePO4 SPHERISCAN SPHERILIGHT...
-
Page 17: Optional Accessories
OPTIONAL ACCESSORIES C21090 - Handle kit C21091 - Fixing Plate Kit C21092 - Cover Kit C21093 - Mirror Kit SPHERISCAN SPHERILIGHT... -
Page 18: Technical Information
TECHNICAL INFORMATION (21.65") (14.72") (34.88") (34.88") (20.16") (14.09") (16.34") (16.34") (19.57") (20.55") (11.81") (7.24") (7.24") (19.61") (6.38") (7.80") (7.80") (15.20") Power supplies Weight • N° 1 Rotating Prism (8 faces) 200/240V 50/60 Hz • Spheriscan: 35 Kg (77 lbs), 32 Kg (70.5 lbs) •... -
Page 19: Cause And Solution Of Problems
CAUSE AND SOLUTION OF PROBLEMS THE PROJECTOR WILL NOT SWITCH ON PROBLEMS ELECTRONICS NON-OPERATIONAL DEFECTIVE PROJECTION POSSIBLE CAUSES CHECKS AND REMEDIES REDUCED LUMINOSITY No mains supply. Check the power supply voltage. Lamp exhausted or defective. Replace the lamp. (See instructions). Signal transmission cable faulty or disconnected. - Page 20 CLAY PAKY - Via Pastrengo, 3/b - 24068 Seriate (BG) Italy - Tel. +39-035-654311 - Fax +39-035-301876 - www.claypaky.it S.p.A.