Zodiac TornaX Instructions For Installation & Use
  1. Manuals
  2. Brands
  3. Zodiac Manuals
  4. Swimming Pool Vacuum
  5. TornaX
  6. Instructions for installation & use

Zodiac TornaX Instructions For Installation & Use

Hide thumbs Also See for TornaX:
Table of Contents

Advertisement

Quick Links

TornaX
Instructi ons for installati on and use
EN
English
More documents on:
www.zodiac-poolcare.com
EP31--
H0575900.A - 2016/12 -

Advertisement

Table of Contents
loading

Related Manuals for Zodiac TornaX

Summary of Contents for Zodiac TornaX

  • Page 1 TornaX Instructi ons for installati on and use English More documents on: www.zodiac-poolcare.com EP31-- H0575900.A - 2016/12 -...
  • Page 2 Notes...
  • Page 3 fi re. • Zodiac® heat pump, fi ltrati on pump and fi lter appliances are compati ble with the most commonly used types of pool water treatment systems. • For heat pump appliances or dehumidifi ers, do not touch the fan or insert a rod or your fi ngers through the grid when the appliance is in operati on.

  • Page 4: Table Of Contents

    The distributi on or modifi cati on of this document in any way is prohibited, without prior • authorisati on from Zodiac®. Zodiac® is constantly developing its products to improve their quality. The informati on • contained herein may therefore be modifi ed without noti ce.

  • Page 5: ❶ Specifi Cati Ons

    ❶ Specifi cati ons 1.1 I Descripti on Cleaner + fl oati ng cable Control box Base for control box 100µ fi ne debris fi lter 200µ large debris fi lter 60µ very fi ne debris fi lter Standard fl ap brush / Tile brush (depending on the model) Tile brush Caddy kit...

  • Page 6: I Technical Specifi Cati Ons And Marking

    1.2 I Technical specifi cati ons and marking 1.2.1 Technical specifi cati ons Control box power supply voltage 100-240 VAC, 50/60 Hz Cleaner power supply voltage 30 VDC Maximum power input 100 W Cable length 14 m or 16.5 m (depending on the model) Cleaner size (L x W x h) 37 x 29 x 30 cm Package size (L x W x h)

  • Page 7: ❷ Installati On

    ❷ Installati on 2.1 I Set-up 3.5 meters : Control box Minimum : Base : Cleaner : Floati ng cable : Plug : Power cord 2.2 I Att achment to the base...

  • Page 8: ❸ Use

    ❸ Use 3.1 I Operati ng principle The cleaner is independent of the fi ltrati on system and can therefore operate autonomously. It just simply needs to be connected to the mains power supply. It fi nds the best route to move around and clean the areas of the pool for which it has been designed (depending on the model: bott om only, bott om and walls).

  • Page 9: I Electricity Supply Connecti Ons

    3.4 I Electricity supply connecti ons • Use of an electrical extension is prohibited when connecti ng the control box. • Make sure that the socket can be easily accessed at all ti mes and is protected from rain or splashes.

  • Page 10: I Starti Ng The Cleaning Cycle

    3.5 I Starti ng the cleaning cycle • Bathing is prohibited when the appliance is in the pool. • Do not use the appliance during shock chlorinati on. • Do not leave the appliance unatt ended for an extended period. •...

  • Page 11: I Ending The Cleaning Cycle

    3.6 I Ending the cleaning cycle • To avoid damaging the unit, use the cleaner's handle to raise the cleaner and remove it from the pool. Do not pull on the fl oati ng cable. • Take the appliance out of the water each ti me cleaning is complete. •...

  • Page 12: ❹ Maintenance

    ❹ Maintenance • The appliance must be cleaned regularly using clean or slightly soapy water. Do not use solvents. • Rinse the appliance thoroughly with clean water. • Do not let your appliance dry in the sun by the pool. Tip: replace the fi...

  • Page 13: I Cleaning The Propeller

    4.2 I Cleaning the propeller To avoid serious injury: • Disconnect the cleaner from the power supply. • Wear gloves when handling the propeller • Remove the fi lter using the handle (see image • Remove the external fl ow guide by lift ing it so as to clear the clips (see image •...

  • Page 14: I Replacing The Brush

    4.3 I Replacing the brush • The brush is equipped with wear indicators; the distance between the indicators and the end of the brush indicates whether the brush is in good conditi on (see image • The brush is worn and should be replaced when the wear indicators appear as shown in image •...

  • Page 15: I Replacing The Tracks

    4.4 I Replacing the tracks • Place the cleaner on its side (see image • Starti ng with one of the wheels, pull on the inside of the track to separate it from the wheel (see image Then remove the track from the cleaner. •...

  • Page 16: ❺ Troubleshooti Ng

    ❺ Troubleshooti ng • If a problem occurs, before you contact your retailer, please carry out these few simple checks using the following tables. • If the problem conti nues, contact your retailer. • : Acti ons to be performed by a qualifi ed technician only 5.1 I Appliance behaviour When the cleaner moves forward in a straight line, it is no longer fl...

  • Page 17: I User Alerts

    5.2 I User alerts Soluti ons Flashing LED: • Check that the cleaner is correctly connected to the control box. If necessary, unplug it and reconnect it following the appropriate procedure. • Check that there is nothing preventi ng the brush and support from turning.
  • Page 18 Votre revendeur Your retailer Modèle appareil Appliance model Numéro de série Serial number Trouvez plus d’informations et enregistrez votre produit sur More informations and register you product on www.zodiac-poolcare.com ZODIAC® is a registered trademark of Zodiac International, S.A.S.U., used under license.

Table of Contents