Bosch Power Xpress Installation Instructions Manual
Bollard charge station
Hide thumbs
Also See for Power Xpress:
- Installation and operating instructions manual (26 pages) ,
- Installation instructions manual (38 pages) ,
- Firmware field update instructions (4 pages)
Related Manuals for Bosch Power Xpress
Summary of Contents for Bosch Power Xpress
- Page 1 Power Xpress™ Bollard Charge Station Installation Guide en Installation Instructions...
-
Page 2: Technical Support
Copyright © 2016 Bosch Automotive Service Solutions Inc. All rights reserved. The information, specifications, and illustrations in this guide are based on the latest information available at the time of printing. Bosch Automotive Service Solutions Inc. reserves the right to make changes at any time, without notice. -
Page 3: Table Of Contents
Power Xpress™ Bollard Charge Station Installation Guide | 1 | en Table of Contents 1. Installation Safety 2. Installation Contents: Bollard and EVSE 2.1 Power Xpress EVSE (EL-50600-300) for Bollard Charge Station 2.2 Bollard and Hardware (EL-50600-500) 3. Tools Suggested for Installation (Not Provided) 4. -
Page 4: Installation Safety
| 2 | Power Xpress™ Bollard Charge Station Installation Guide Installation Safety Installation Contents: Bollard and EVSE (EL-50600-300) SAVE THESE IMPORTANT SAFETY INSTRUCTIONS 2.1 Power Xpress EVSE (EL-50600-300) for Bollard This guide contains important instructions that must Charge Station be followed during the installation of the electric vehicle supply equipment (EVSE). -
Page 5: Tools Suggested For Installation (Not Provided)
Power Xpress™ Bollard Charge Station Installation Guide | 3 | en Tools Suggested for Installation WARNING: The EVSE is a single-phase device. Do (Not Provided) not connect all three phases of a 3-phase feed. Only three wires are connected, take care that... -
Page 6: 240V 3-Phase Delta Connection (North America) With Center Tap On One Leg
| 4 | Power Xpress™ Bollard Charge Station Installation Guide WARNING: The EVSE is a single-phase device. When 4.3 240V 3-Phase Delta Connection (North America) connecting the line and neutral wires, take care with Center Tap on One Leg... -
Page 7: Electrical Requirements For Battery Charging
Power Xpress™ Bollard Charge Station Installation Guide | 5 | en Using a small, flat-blade screwdriver, set the current-adjust- WARNING: The EVSE must be installed by a licensed ment selector to the applicable output current-limiting electrician in accordance with all national and setting as specified in “Figure 8. -
Page 8: Standard Installation
| 6 | Power Xpress™ Bollard Charge Station Installation Guide Standard Installation Lay down the bollard box and remove the banding. Lift the top off the box and remove the bollard from the packaging material. Remove the upper cover from the bollard assembly by removing the cable-management retaining screws (E) on the rear of the bollard. - Page 9 Power Xpress™ Bollard Charge Station Installation Guide | 7 | en Install 1/2-in. liquid-tight flexible conduit to the conduit 14. Install a washer, lock washer, and nut on each bolt. stand pipe. NOTE: Consult national and local codes for approved, liquid- tight flexible conduit.
- Page 10 | 8 | Power Xpress™ Bollard Charge Station Installation Guide 21. Feed wires into the hole in the top of the EVSE and attach 17. Gently guide the EVSE body down through the bollard until it 1/2-in. liquid-tight flexible conduit with a liquid-tight fitting.
- Page 11 Power Xpress™ Bollard Charge Station Installation Guide | 9 | en 25. Apply decal to the front of the EVSE cover. 28. Install the locating set screw to 50 ± 5 in-lb (5.5 ± 0.55 Nm). 26. Continue lowering the EVSE until the front edge of the EVSE bottom cover rests on the ledge in the bollard front opening.
- Page 12 | 10 | Power Xpress™ Bollard Charge Station Installation Guide 31. Carefully lower the upper plastic cover down onto the bol- 33. While gently pressing down on the upper plastic cover, lard base. carefully slide the screwdriver around the bollard to extend the upper lip of the seal over the upper plastic cover.
-
Page 13: Evse Power And Status Led Indications
Power Xpress™ Bollard Charge Station Installation Guide | 11 | en 36. Switch the main circuit breaker to the ON position and verify Power and Status LED that the Power LED is illuminated solid green and the Status Indications LED is illuminated solid amber on the EVSE. -
Page 14: Troubleshooting
IMPORTANT: It is the Purchaser’s obligation to register the Charging Reconnect the coupler to the vehicle Station with Bosch and failure to do so may delay warranty support. To port. register a Charging Station online, go to BoschEVSolutions.com or call 1-877-805-3873 for assistance. -
Page 15: Limitation Of Liability
Disclaimer and under no obligation to return the Charging Station, at its ex- pense. If you do not contact Bosch within five (5) business days of its TO THE EXTENT PERMITTED BY APPLICABLE LAW AND EXCEPT AS delivery, Bosch will dispose of the shipment in a manner of its choice EXPRESSLY PROVIDED IN THE LIMITED WARRANTY, BOSCH without any liability to you. - Page 16 Bosch Automotive Service Solutions Inc. 28635 Mound Road Warren, MI 48092 USA Phone: (877) 805-EVSE (3873) www.pluginnow.com...