Download  Print this page

HP CF283X Technical Manual

Remanufacturing the toner cartridge for hp laserjet pro m201 series; hp laserjet pro m225 series
Hide thumbs

Advertisement

Quick Links

T e c h n i c a l G u i d e
Remanufacturing the
HP LaserJet Pro M201, MFP M225
series toner cartridge (CF283X)
By Mike Josiah and the Technical Staff at Uninet

Advertisement

loading

  Related Manuals for HP CF283X

  Summary of Contents for HP CF283X

  • Page 1 T e c h n i c a l G u i d e Remanufacturing the HP LaserJet Pro M201, MFP M225 series toner cartridge (CF283X) By Mike Josiah and the Technical Staff at Uninet...
  • Page 2: Required Supplies

    By Mike Josiah and the Technical Staff at Uninet In December 2013, HP released the LaserJet Pro M201 series. The M201 laser printers are based on a 26ppm, 600 x 600dpi (1,200dpi with Fast Res) Canon engine. The CE283X is rated for 2,200 pages.
  • Page 3: Technical Guide

    TECHNICAL GUIDE By Mike Josiah and the Technical Staff at Uninet STEP ONE With the handle facing you, remove the right side screw and end cap from the cartridge. Be careful of the drum cover spring! Remove it with the end cap. STEP TWO With the pair of needle-nose pliers, release both the hopper tension springs.
  • Page 4 TECHNICAL GUIDE By Mike Josiah and the Technical Staff at Uninet STEP FIVE Remove the PCR and clean with your standard PCR cleaner. STEP SIX Remove the two screws and the wiper blade. STEP SEVEN Clean out all the waste toner from the hopper. Be careful not to damage the recovery blade located next to the wiper blade.
  • Page 5 TECHNICAL GUIDE By Mike Josiah and the Technical Staff at Uninet STEP TEN Place another small amount of conductive grease on to the metal drum axle. STEP ELEVEN Install the new/cleaned drum hub side first. STEP TWELVE Place the waste/drum section aside. STEP THIRTEEN On the toner supply chamber right side, remove the two screws and end cap.
  • Page 6 Clean out all the remaining toner from the hopper. Make sure the magnetic roller seals and the doctor blade seals are all clean. STEP NINETEEN Fill the hopper with toner for use in the CF283X cartridge. ©2015 Recycler Publishing & Events Ltd THE RECYCLER - TECHNICAL GUIDE PAGE 6...
  • Page 7 TECHNICAL GUIDE By Mike Josiah and the Technical Staff at Uninet STEP TWENTY There are two screws holding the doctor blade in place. To install a seal, remove the seal port plug, and install The left screw is a normal thread screw; the right side the seal.
  • Page 8 TECHNICAL GUIDE By Mike Josiah and the Technical Staff at Uninet STEP TWENTY-FOUR Install the gears as shown. STEP TWENTY-FIVE Install the end cap and screws. STEP TWENTY-SIX Place the drum/waste hopper into the toner hopper. Slide it over so the round hinge pins fit into their respective holes.
  • Page 9 TECHNICAL GUIDE By Mike Josiah and the Technical Staff at Uninet STEP TWENTY-EIGHT With the drum cover spring as shown on the end cap, install the end cap. Lift up the tail of the spring to fit onto the hopper. STEP TWENTY-NINE Lift up the drum cover sprint tail to fit as shown on the drum cover.
  • Page 10 TECHNICAL GUIDE By Mike Josiah and the Technical Staff at Uninet NOTES THE RECYCLER - ISSN 2045-2047 (Print) THE RECYCLER TEAM THE RECYCLER Editor & Publisher David Connett - publisher@therecycler.com Wittas House, Two Rivers, Station Lane, Witney, Deputy Publisher United Kingdom OX28 4BH Stefanie Unland –...