Daikin FDY125B7V1 Installation Manual
Hide thumbs Also See for FDY125B7V1:

Advertisement

INSTALLATION MANUAL

Split System air conditioners
FDY125B7V1
FDY200B7V1
FDY250B7V1
FDYP125B7V1
FDYP200B7V1
FDYP250B7V1
FDQ125B7V3B

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FDY125B7V1 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Daikin FDY125B7V1

  • Page 1: Installation Manual

    INSTALLATION MANUAL Split System air conditioners FDY125B7V1 FDY200B7V1 FDY250B7V1 FDYP125B7V1 FDYP200B7V1 FDYP250B7V1 FDQ125B7V3B...
  • Page 2 125 class: >350 200+250 class: >450 >300 1440 602 (125 class) 840 (200+250 class) 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 L N P 1 2 3 L N P 1 2 3 L N P 1 2 3...
  • Page 3 ™ËÌ›ˆÛË Nota tal como estabelecido no Ficheiro Técnico de Construção DAIKIN.TCF.004, .016, .021 e com o parecer positivo de KEMA de acordo com o Certificado 59277-KRQ/ECM95-4233/81728-KRQ/EMC98-4341/2024351-QUA/EMC02-4565 . Bemærk som anført i den Tekniske Konstruktionsfil DAIKIN.TCF.004, .016, .021 og positivt vurderet af KEMA i henhold til Certifikat 59277-KRQ/ECM95-4233/81728-KRQ/EMC98-4341/2024351-QUA/EMC02-4565 .
  • Page 4: Table Of Contents

    OTHER DAMAGE TO THE EQUIPMENT. BE SURE ONLY environment (e.g. a place in oily surroundings, a place with TO USE ACCESSORIES MADE BY DAIKIN WHICH ARE sulfide gas, a place where chemicals are used nearby, a SPECIFICALLY DESIGNED FOR USE WITH THE place with high voltage fluctuations, a place with volatile...
  • Page 5: Preparations Before Installation

    Do not install the unit tilted. REPARATIONS BEFORE INSTALLATION (If the unit is tilted against condensate flow, water can drip out of the drain pan). Suspension bolt position (Refer to figure Check if the unit is levelled at all four corners with a water level (1) or The fan speed for this indoor unit is preset to provide standard a water-filled vinyl tube (2) (Refer to figure...
  • Page 6: Vacuum Drying Of Installation

    Methods of wiring units and connecting remote ACUUM DRYING OF INSTALLATION controller cords (Refer to figure Refer to the installation manual of the outdoor unit. Wiring the units (Power supply wiring). Connect the interconnection wiring (from outdoor to indoor) to RAIN PIPING WORK the 1-2-3 terminal (1) using a separate power supply wire to connect to power supply of the indoor unit fan motor to the L-N...
  • Page 7: Field Setting

    NOTES IELD SETTING Setting external static pressure Depending on the external static pressure (ducts, filter, etc.) which is connected to the air conditioning unit the fan speed should be set by changing the wires in the switch box. (Refer to figure Factory set: fan speed is M.
  • Page 8: Internal Wiring - Parts Table

    NTERNAL WIRING PARTS TABLE Refer to the wiring diagram on the unit. The abbreviations used are listed below. NOTE When using the central remote controller, see manual for connection to the unit. Ground the shield of the remote controller cord to the indoor unit.
  • Page 9 NOTES NOTES...
  • Page 10 Zandvoordestraat 300, B-8400 Oostende, Belgium 4PWEN10621-1C...

Table of Contents