Generac Power Systems QT 100 Owner's Manual page 51

2 0D5418
3 052625
(2) 4 047411 1 / 2
5 0D5623
6 0D2608
7 070006
8 070008
9 055934M
10 0G0321
11 046526
12 057823
13 057765
14 046964
15 0D5417 REF.
16 049821
17 022129
18 070010
(2) 19 0F2776A 1 / 2
(2) 20 022097 1 / 2
21 048191
(2) 22 022473 1 / 2
(1) 23 029333A
24 0D9913
25 055596
26 069860E
27 0D4255
28 057772
29 0D6686
30 0D3803
31 0D3805
32 021113
33 077996
34 022131
35 0C7649
36 052647
37 0D2244M
38 0D3808
39 0F5114
41 079121
43 057823
44 053660
45 087599
(1) NOTE: I/N 23 IS FOR HOLDING SENSORS TO I/N 19.
(2) QTY. REQ. FOR NON-MQT / QTY REQ. FOR MQT EPA CERT. (NOT REQUIRED
1 STARTER MOTOR FORD V-10 ENGINE
11 SCREW SHC M10-1.5 X 35 G12.9
SCREW HHC M6-1.0 X 16 G8.8
2 HEAT SHIELD EXHAUST
10 SCREW HHC 5/16-18 X 1/2 SSTL
30 WASHER LOCK M8 SSTL
10 WASHER FLAT M8 SS
1 CLAMP VINYL .75 X .343 Z
1 HOSE COOL 5/8" ID 250#WP (14")
23 WASHER LOCK M10
1 CLAMP HOSE #10 .56 - 1.06 (2300 & 3000RPM UNITS ONLY)
1 ADAPTER M14-1.50 X 3/8 NPT
1 ELBOW 90D 1/4 NPT F-M BRASS
SCREW HHC M10-1.0 X 25 G10.9
3 SCREW SHC M8-1.25 X 30 G12.9
3 WASHER LOCK M8-5/16
2 SCREW HHC M8-1.25 X 35 SS F-TH
BRACKET SIGNAL CONDITIONER
WASHER LOCK M6-1/4
2 DOWEL PIN M10 X 24
WASHER FLAT 1/4 ZINC
1 TIE WRAP UL 7.4" X .19" BLK (NOT SHOWN)
18 SCREW SHC M8-1.25 X 35 SS
1 BARBED STR 3/8 NPT X 3/8
1 HOSE DRAIN ASSY 28"
2 GASKET EXHAUST MANIFOLD
1 WASHER NYLON .565
1 ASSEMBLY 6.8L G-BOX FLYWHEEL
1 FLYWHEEL HOUSING MACH 6.8L V10
1 COVER FLYWHEEL MACH 6.8L V-10
1 PLATE DAMPNER RETNR
1 CAP HOSE (2300 & 3000RPM UNITS ONLY)
7 WASHER FLAT 3/8-M10 ZINC
1 CLAMP HOSE .38-.87
9 SCREW SHC M10-1.5 X 25 G12.9
1 ASSY MAGPICKUP(3/8-24 MALE)
2 EXH MANIFOLD MACH 6.8L V-10
1 DECAL REFER TO OWNERS MANUAL
2 SCREW SHC M10-1.50 X 100 G10.9
2 CLAMP HOSE #10 .56-1.06
1 BARBED STR 1/4 NPT X 5/8
1 PLUG PLASTIC 3/8 NPT
FOR NEXUS CONTROL PANELS)