Generac Power Systems QT 100 Owner's Manual page 49

1 0F3017
2 039253
3 022129
4 022145
(2) 5 0D5419
6 0D7055
7 0D3488G
0D3488J
0D3488
0D3488K
8 057795A
9 059057
10 0F3287
(3) 11 0F5990
0H2595
0F4419
0H3081
0F9786
0H3080
12 0E9868A
13 057796
14 0F3216
0F3216A
0F3216C
0F3216D
15 035579
16 0F4612
17 0D6658
(3) (1) 18 029333A
19 022097
20 022473
21 042568
22 0D8027
23 0D8025
24 0D8026
25 0D8030
26 0F2846
0D8029
27 0D8028
28 045771
29 0D3454A
0H0923
30 022131
31 046526
32 064416
33 045772
34 0F3217
35 0F2776A
36 0F6151
37 0F4308
38 0F3158
39 057823
40 0E0502
41 0G0866
42 0F4301
44 047527
45 057823
46 0E0992A
47 078637
48 0G7519
49 0E8286
(1) NOTE: I/N 18 IS FOR HOLDING SENSOR TO I/N 35.
(2) I/N 5 PART OF I/N 29.
(3) NOTE: NOT SHOWN)
1 BRACKET,D.C. ALTERNATOR LOWER
3 SCREW HHC M8-1.25 X 20 G8.8
4 WASHER LOCK M8-5/16
4 WASHER FLAT 5/16-M8 ZINC
REF OIL FILTER, FORD V-10 ENGINE
1 DIPSTICK TUBE, FORD 6.8L
1 BELT SERPENTINE (65.0" LG) (1800 RPM)
1 BELT SERPENTINE (65.3" LG) (2300 RPM)
1 BELT SERPENTINE (67.16" LG) (3000 RPM)
1 SERPENTINE BELT (68.3" LG) (3600 RPM)
1 BARBED EL 90 3/4 PLASTIC
1 HOSE 3/4 ID SAE-30R2 (16.75"LG)
1 BRACKET DC ALTERNATOR UPPER
1 HARN ENG 6.8L H-100 (USE WITH PROBE P/N 0E2507)
1 HARN ENG G6.8L G3 H-100 (USE WITH PROBE P/N 0H1827)
1 HARN ENG 6.8L G-100 (USE WITH PROBE P/N 0E2507)
1 HARN ENG G6.8L G3 MQT 480V (USE WITH PROBE P/N 0H1827)
1 HARN ENG 6.8L G-100 MQT 208V (USE WITH PROBE P/N 0E2507)
1 HARN ENG G6.8L G3 MQT 208V (USE WITH PROBE P/N 0H1827)
1 ALTERNATOR DC W/OUT PULLEY
1 GROMMET
1 PULLEY 80 OD DC ALTERNATOR (1800 RPM)
1 PULLEY 102 OD DC ALTERNATOR (2300 RPM)
1 PULLEY 132 OD DC ALTERNATOR (3000 RPM)
1 PULLEY 160 OD DC ALTERNATOR (3600 RPM)
1 BSHG RDCR HEX 1/4 TO 1/8
1 SENDER OIL PRESSURE 1/8" NPT
1 DIPSTICK 6.8L FORD
2 TIE WRAP UL 7.4" X .19" BLK
3 WASHER LOCK M6-1/4
3 WASHER FLAT 1/4 ZINC
3 SCREW HHC M6-1.0 X 20 G8.8
4 BOLT WATER PUMP PULLEY
1 BOLT GROOVED IDLER PULLEY
3 BOLT BELT TENSIONER
1 TENSIONER ENG. AUTOMATIC BELT
1 PULLEY WATER PUMP FORD (1800RPM UNITS)
1 PULLEY ENGINE WATER PUMP (2-POLE & GEAR BOX)
1 PULLEY GROOVED ENGINE IDLER
1 NUT HEX M8-1.25 G8 YEL CHR
1 ENGINE G6.8L G3 V-10
1 ENGINE G6.8L G3 V-10 (2009)
2 WASHER FLAT 3/8-M10 ZINC
1 WASHER LOCK M10
1 SCREW HHC M10-1.5 X 45 G8.8 FT
1 NUT HEX M10-1.5 G8 YEL CHR
1 SPACER DC ALTERNATOR PULLEY
1 BRACKET SIGNAL CONDITIONER
1 CAP RUBBER
1 BRACKET DC ALT STABILIZER
1 OIL COOLER FORD (150KW 3600RPM)
2 CLAMP HOSE #10 .56-1.06
1 TEMPERATURE SENDER DELPHI
1 HOSE OIL COOLER PREFORMED 3/4 (150KW 3600RPM)
1 HOSE OIL COOLER (150KW 3600RPM)
1 BARBED STR 1/2NPT X 3/4
4 CLAMP HOSE #10 .56-1.06 (150KW 3600RPM)
10 PLUG EXPANSION 14 OD
A/R ADHESIVE LOCTITE 620
1 DECAL EMISSION CTRL INFO 6.8L
1 ELBOW 45D STREET 1/2NPT BRASS