Mixer Installation - Pentair HBM 200 series Installation And Service Manual

General
Information
Attention:
This manual contains important
information for the safe use of
this product. Read this manual
completely before using this
product and refer to it often for
continued safe product use. Do
not throw away this manual. Keep
it in a safe place so that you may
refer to it often.
Reasonable care and safe methods
should be practiced. Check the
local codes and requirements
before installation.
WARNING: Before handling
electrical equipment, always
disconnect the power first. Do not
smoke or use sparkable electrical
devices or flames in a septic
(gaseous) or possible septic sump.
CALIFORNIA PROPOSITION
65 WARNING:
This product
and related accessories contain
chemicals known to the State of
California to cause cancer, birth
defects or other reproductive harm.
CAUTION: To reduce risk of
electrical shock, do not remove
cord or strain relief. Do not
connect conduit to mixer.
Electrical installations shall be
in accordance with the National
Electrical Code and all applicable
local codes and ordinances.
For use with maximum
140°F water.
Septic tank should be vented in
accordance with local plumbing
codes and should not be installed
in locations classified as
hazardous, in accordance with the
National Electrical Code, ANSI/
NFPA 70-1999.
2
WARNING: Severe injury may
result from accidental contact
with moving propeller. Keep
clothing, hands and feet away
from propeller any time power is
connected to the mixer.
The Mixer
Description:
The integral stainless steel motor
shaft is sealed by two mechanical
seals with an oil chamber between
the seals to provide lubrication
for both seal faces.
Two ball bearings are used to
handle the loads. The upper
bearing takes radial load, while
the larger lower bearing handles
both thrust and radial loads.
Both bearings are permanently
lubricated by the dielectric oil in
the motor housing. The motor is
fixed within the motor housing
and is completely submerged in
the dielectric oil for maximum
heat transfer. The motor housing
and seal chamber are completely
sealed with O-rings located at
mating part faces.
The power cord entry system is
designed to give double sealing.
The chamfered pilot of the motor
housing mates with the molded
cord end to form the first seal.
The cord grip forms the second
seal around the molded cord end
and provides strain relief. The
cable includes the leads for both
heat sensors (motor protection)
and the seal sensor lead for seal
leakage detection.
Application:
The submersible basin mixer is
used to break up crusts and solids
that float at the top of a solids
handling basin. The unit can also
be used for mixing and stirring
applications in industrial areas
and waste management facilities.

Mixer Installation

Unpacking:
Remove from carton. When
un pack ing unit, check for
concealed damage. Claims
for damage must be made at
the receiving end through the
delivery carrier. Dam age cannot
be processed from the factory.
Location:
If mixers are installed in an
existing basin or concrete sump,
they may either be connected
permanently or rails and brackets
can be fur nished for mounting
to walls of basin. The complete
factory built packaged system
is recommended for the most
satisfactory in stalla tion and
generally for the low est cost
where expensive in stalla tion
labor is involved.
SENSOR LEADS
SENSOR LEADS
WHITE W/BLACK STRIPE - P1
WHITE W/BLACK STRIPE - P1
BLUE - P2
BLUE - P2
ORANGE - SEAL PROBE
ORANGE - SEAL PROBE
MOTOR LEADS
MOTOR LEADS
SENSOR LEADS
230V (DUAL VOLTAGE) THREE PHASE
WHITE W/BLACK STRIPE - P1 230V (DUAL VOLTAGE) THREE PHASE
BLUE - P2
WHITE BLACK RED
WHITE BLACK RED
ORANGE - SEAL PROBE
L1 L2 L3
P1 (PURPLE)
L1 L2 L3 P1 (PURPLE)
P2 (DARK BROWN)
P2 (DARK BROWN)
T1 T2 T3
T1 T2 T3
MOTOR LEADS
(BLUE) (TAN) (ORANGE)
(BLUE) (TAN) (ORANGE)
T7 T8 T9
T7 T8 T9
230V (DUAL VOLTAGE) THREE PHASE
(PINK) (RED) (LT. BROWN)
(PINK) (RED) (LT. BROWN)
WHITE BLACK RED
L1 L2 L3
P1 (PURPLE)
P2 (DARK BROWN)
T4 T5 T6
T4 T5 T6
T1 T2 T3
(YELLOW) (BLACK) (LAVENDER)
(YELLOW) (BLACK) (LAVENDER)
(BLUE) (TAN) (ORANGE)
T7 T8 T9
460V (DUAL VOLTAGE) THREE PHASE
460V (DUAL VOLTAGE) THREE PHASE
WHITE BLACK RED
WHITE BLACK RED
(PINK) (RED) (LT. BROWN)
L1 L2 L3
L1 L2 L3
PL (PURPLE)
PL (PURPLE)
T1 T2 T3
T1 T2 T3
P2 (DARK BROWN)
P2 (DARK BROWN)
(BLUE) (TAN) (ORANGE)
(BLUE) (TAN) (ORANGE)
T4 T5 T6
(YELLOW) (BLACK) (LAVENDER)
T7 T8 T9
T7 T8 T9
(RED)
(PINK)
(LT. BROWN)
(PINK) (RED)
(LT. BROWN)
T4 T5 T6
460V (DUAL VOLTAGE) THREE PHASE
T4 T5 T6
(YELLOW) (BLACK) (LAVENDER)
(YELLOW) (BLACK) (LAVENDER)
WHITE BLACK RED
L1 L2 L3
PL (PURPLE)
T1 T2 T3
P2 (DARK BROWN)
(BLUE) (TAN) (ORANGE)
T7 T8 T9
(RED)
(PINK)
(LT. BROWN)
T4 T5 T6
(YELLOW) (BLACK) (LAVENDER)