Unimac UM-SP-35 User Manual page 5

Product Manual – Airless Spray Painter
Electrical Safety
When using mains-powered tools, basic
safety precautions, including the following,
should always be followed to reduce risk of
fire, electric shock, personal injury and
material damage. The electric motor has
been designed for 230V and 240V only. If
the supply cord is damaged, it must be
replaced by an electrician or a power tool
repairer in order to avoid a hazard. If using
an Extension Lead Always
approved extension lead suitable for the
power input of this tool. Before use, inspect
the extension lead for signs of damage,
wear and ageing. Replace the extension
lead if damaged or defective. When using an
extension lead on a reel, always unwind the
lead completely. Use of an extension lead
not suitable for the power input of the tool or
which is damaged or defective may result in
a risk of fire and electric shock. Power tool
plugs must match the outlet. Never modify
the plug in any way. Do not use any
international / converter / adapter plugs with
earthed (grounded) power tools. Unmodified
plugs and matching outlets will reduce risk
of electric shock. Avoid body contact with
earthed or grounded surfaces, such as
pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if
your body is earthed or grounded. Do not
expose power tools to rain
conditions. Water entering a power tool will
increase the risk of electric shock. Do not
abuse the cord. Never use the cord for
carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or
entangled cords increase the risk of electric
shock. When operating a
outdoors, use an extension cord suitable for
outdoor use. Use of a cord suitable for
outdoor use reduces the risk of electric
shock. Use a residual current device
(RCD) protected supply. Use of an RCD
reduces the risk of electric shock.
Airless spray gun safety warnings
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
NEVER under any circumstances aim the
nozzle at another person or animal. In the
event of an injury occurring, seek medical
advice immediately. The spray gun must
not be used for spraying flammable paints
and solvents. Always ensure there is
adequate ventilation when spraying. The
use of ear protection is recommended. Eye
protection is recommended
hazardous vapours and liquids out of eyes.
Always wear a face mask when spraying.
150914120800
Always read the
thinning instructions before using. Always
keep the spray basket nozzle in place
during use. Never allow the spray to come in
direct contact with the skin. NEVER
immerse the spray gun in liquid. This could
lead to electric shock, personal injury and
material damage. The spray gun must not be
cleaned by using flammable liquids. NEVER
spray near a naked flame, including an
appliance pilot light. NEVER smoke whilst
use an
spraying. NEVER allow children to operate
or play with the spray gun. Before cleaning,
always disconnect the appliance from the
mains supply. Always
mains supply when refilling the paint pot.
After every use ensure you clean your
spray gun thoroughly. NEVER use the spray
gun outside when it is raining. Keep
electrical equipment at a safe distance from
spray painting zones. Avoid old footwear or
footwear with paint, oil or wax stained
soles. When cleaning the spray gun, check
that the high voltage supply is switched off.
Care should be taken to prevent static
discharge during
Information on controlling static electricity
can be found in AS/NZS 1020: The control
of undesirable static electricity. The Airless
Spray Gun operates at a very high
pressure. For safe operation the following
must be observed at all times. Do not point
or wet
the spray gun at yourself or any other
person. Injury from penetration to the skin
and paint solvents being injected into the
body can result. Always check for leaks
and correct operation before use. Never
operate the spray gun if there are any
leaks or faults. Faults or leaks can cause
injury. Release the pressure when not in
power tool
use. Pressure can remain in the unit and
hose when switched off. Injury where paint
or solvent injection into the skin or body
occurs can be very serious. Always seek
professional medical help and advise the
paints or solvents used.
Fire and explosion hazard
Flammable fumes, such as solvent and paint
fumes, in work area can ignite or explode.
To help prevent fire and explosion: Use
equipment only in well- ventilated area.
Eliminate all ignition sources; such as pilot
lights, cigarettes, portable electric lamps,
and plastic drop cloths (potential static arc).
Sprayer generates
flammable liquid is used in or near the
sprayer or for flushing or cleaning, keep
sprayer at least
20 feet (6 m) away from explosive vapours.
Keep work area free of debris, including
solvent, rags and gasoline. Do not plug or
unplug power cords or turn lights on or off
when flammable
to keep
Ground equipment and conductive objects
UNIMAC Airless Paint Sprayer
paint manufacturers in work area. If there is static sparking or you
feel a shock, stop operation immediately. Do
not use equipment until you identify and
correct the problem. Keep a working fire
extinguisher in the work area.
Skin injection hazard
High-pressure fluid from gun, hose leaks,
or ruptured components will pierce skin. This
may look like just a cut, but it is a serious
injury that can result in amputation. Get
immediate surgical treatment. Do not point
gun at anyone or at any part of the body. Do
not put your hand over the spray tip. Do not
stop or deflect leaks with your hand, body,
disconnect from
glove, or rag. Engage trigger lock when not
spraying. Follow Pressure Relief Procedure
in this manual, when you stop spraying and
before cleaning, checking, or servicing
equipment.
Confined spaces
Spray painters sometimes have to work
fully or partly in confined spaces with poor
ventilation or restricted entry and exit
points. The main hazards presented by this
type of work environment are lack of oxygen,
spray painting.
toxic or flammable and explosive vapours,
engulfment and mechanical equipment.
Associated health risks include burns,
electrocution, suffocation and asphyxiation,
poisoning,
and death. If possible, remove the object to
be painted from the confined space. Use
mechanical ventilation systems and non-
sparking tools (if there is a
atmosphere).
respiratory device is needed, protect the
breathing line at all times. Allow only people
wearing
equipment (PPE) to enter the space. More
information
found in the Confined Spaces Code of
Practice.
Toxic fluid or fumes hazard
Toxic fluids or fumes can cause serious
injury or death if splashed in the eyes or on
skin, inhaled, or swallowed. Read MSDS's
to know the specific hazards of the fluids
you are using. Store hazardous fluid in
approved containers and dispose of it
according to any applicable guidelines.
NEVER use the following in your airless
sprayer;
sparks. When
- Bleach, chlorine products or other
corrosive chemicals.
- Tri-sodium phosphate products.
- Ammonia products.
- Acid-based products.
These chemicals will harm the unit and will
damage the surface being cleaned. Use of
these items will void all warranty. Use a
fumes are present.
standard liquid car wash or similar
detergent.
crush injuries, brain damage
flammable
If an air- supplied
correct personal protective
on confined spaces can be
3
3