Citizen C650 Abbreviated User Manual page 4

Using the timer
You can set the countdown timer up to 99 minutes by 1-minute increments.
• Measurement continues even after changing the mode.
Setting the time to countdown
1.
Push the crown in to position
2.
Rotate the crown to move the mode hand to point [TMR].
The timer is ready on the digital section.
Time set for countdown
3.
Pull the crown out to position
The timer is reset and the time set for countdown blinks.
4.
Rotate the crown to set the time to countdown.
• When you rotate the crown quickly, the indication will change continuously.
To stop the rapid change, rotate the crown.
5.
Push the crown in to position
Using the timer
1.
Push the crown in to position
2.
Rotate the crown to move the mode hand to point [TMR].
The timer is ready on the digital section.
Start/stop: press button .
B
Pressing button during countdown starts countdown again from the time
A
set.
Reset: press button while the countdown is stopped.
A
Be sure to reset the timer and change the mode to [TME] or [CAL] after finishing
countdown.
When the countdown is finished
The time-up tone sounds for 5 seconds.
Press any of the buttons to stop the sound.
Checking the reference position
1.
Push the crown in to position
2.
Rotate the crown to move the mode hand to point [CHR].
3.
Pull the crown out to position
"HR" is displayed on the area name display and all
hands except the mode hand move to the current
reference positions.
Correct reference positions of all hands: 12 o'clock
position
• When the current reference position is different
from the correct one, adjust the position
following the steps of "Correcting the reference
position".
4.
Push the crown in to position
5.
Rotate the crown to move the mode hand to point [TME] to
finish the procedure.
.
0
Remaining time to
countdown
.
2
.
0
.
0
.
0
.
2
.
0
Correcting the reference position
1.
Push the crown in to position
2.
Rotate the crown to move the mode hand to point [CHR].
3.
Pull the crown out to position
4.
Press and release the upper right button
change the hand to be corrected.
• Each time you press button
on the area name display:
"HR" (hour/24-hour hands) → "MIN" (minute/UTC hour/UTC minute hands)
→ "SEC" (second hand) → (back to the top)
5.
Rotate the crown to adjust the target.
• When you rotate the crown quickly, the indication will move continuously.
To stop the rapid movement, rotate the crown.
• Hands except the second hand can be rotated to the both directions,
however, rotate them clockwise just before finishing the setting.
6.
Repeat steps 4 and 5 to set other hands.
7.
Push the crown in to position
8.
Rotate the crown to move the mode hand to indicate [TME] to
finish the procedure.
Resetting the watch - All Reset
• Check the power reserve if it is in the level 3 or 2 before executing All Reset.
1.
Push the crown in to position
2.
Rotate the crown to move the mode hand to indicate [CHR].
3.
Pull the crown out to position
"HR" is displayed on the area name display and all hands except the mode
hand move to the current reference positions.
• After confirming that all the hands stop, proceed to the next step.
4.
Press and release both the upper right button
right button at the same time.
B
All the digital indication lights up as the buttons are released.
5.
Push the crown in to position
A confirmation alarm sounds.
After All Reset
After All Reset, adjust the reference position and set the time and calendar. Set
also the alarm.
C650/C651/C652 Abbreviated instruction
.
0
.
2
repeatedly to
B
, the target changes as follows and is indicated
B
.
0
.
0
.
2
and lower
A
to finish the procedure.
0
4/4