Citizen C650 Abbreviated User Manual page 3

Controlling selectable areas
You can control selectable areas which is displayed when using world time,
calendar, alarm, etc. Areas unnecessary for you can be hidden.
1.
Push the crown in to position
2.
Rotate the crown to move the mode hand to point [SET].
3.
Pull the crown out to position
The digital display blinks.
4.
Rotate the crown to select an area.
5.
Press and release the upper right button
setting of the area.
• Each time you press button
SET: The area is displayed.
• Each time you press button
alternately.
6.
Repeat steps 4 and 5 to select and set other areas.
7.
Push the crown in to position
8.
Rotate the crown to move the mode hand to indicate [TME] to
finish the procedure.
Using the alarm
The alarm sounds for about 15 seconds at the time of the area you set.
• Alarm can be set separately at [AL-1], [AL-2], and [AL-3].
1.
Push the crown in to position
2.
Rotate the crown to move the mode hand to point [AL-1], [AL-2],
or [AL-3].
The area, alarm time and the alarm setting currently set are indicated.
3.
Press and release the lower right button
button repeatedly to select an area.
B
4.
Pull the crown out to position
The alarm setting turns to "ON" and it blinks.
5.
Press and release the upper right button
change the target to be set.
• Each time you press button
Alarm setting
6.
Set the target selected.
• Alarm setting: press button
changes alternately between "ON" and "OF" (OFF).
• Hour/minute of the alarm time: rotate the crown.
When you rotate the crown quickly, the indication will change continuously.
To stop the rapid change, rotate the crown.
7.
Repeat steps 5 and 6 to set other targets.
.
0
.
1
to change the
B
, the setting changes alternately.
B
OFF: The area is hidden.
in this step, the summer time setting changes
A
.
0
.
0
or upper right
A
.
2
repeatedly to
B
, the target changes as follows:
B
Alarm time: Alarm time:
Hour Minute
. Each time you press the button, the setting
A
8.
Push the crown in to position
9.
Rotate the crown to move the mode hand to point [TME] to
finish the procedure.
To stop alarm
Press any of the buttons.
Turning the alarm on/off
1.
Push the crown in to position
2.
Rotate the crown to move the mode hand to point [AL-1], [AL-2],
or [AL-3].
3.
Pull the crown out to position
4.
Press and release the lower right button
• Each time you press button
5.
Push the crown in to position
6.
Rotate the crown to move the mode hand to point [TME] to
finish the procedure.
Checking the alarm
Pressing and holding the button
[AL-3]. The alarm tone can be monitored.
Using the chronograph
Measuring up to 24 hours in 1/100 second increments.
• Measurement continues even after changing the mode.
1.
Push the crown in to position
2.
Rotate the crown to move the mode hand to point [CHR].
The chronograph is ready on the digital section.
3.
Use the chronograph.
Start/stop: press button .
B
• Pressing button during measurement indicates the split time for 10
A
seconds and "SPL" blinks on the digital display.
Reset: press button
while the chronograph is stopped.
A
Be sure to reset chronograph and change the mode to [TME] or [CAL] after
finishing measurement.
C650/C651/C652 Abbreviated instruction
.
0
.
0
.
1
.
A
, on/off of the setting changes alternately.
A
.
0
and while the mode is [AL-1], [AL-2] or
A B
.
0
3/4