Table of Contents
Advertisement
A49/C49/P49/P349
H A N D B O O K
Integrated amplifier/Pre-amplifier/Power amplifier
POWER / STANDBY
POWER / STANDBY
POWER / STANDBY
P HO NO
PH ON O
MUTE
DISPLAY
BALANCE
MUTE
DISPLAY
BALANCE
PHONO
AUX
CD
TUNER
SAT
BD
PVR
AV
SP1
SP2
PHONES
PHONO
AUX
CD
TUNER
SAT
BD
PVR
AV
PHONES
SP1
SP2
POWER
POWER
POWER
Advertisement
Table of Contents
Related Manuals for Arcam A49
Summary of Contents for Arcam A49
- Page 1 A49/C49/P49/P349 H A N D B O O K Integrated amplifier/Pre-amplifier/Power amplifier POWER / STANDBY POWER / STANDBY POWER / STANDBY P HO NO PH ON O MUTE DISPLAY BALANCE MUTE DISPLAY BALANCE PHONO TUNER PHONES PHONO TUNER PHONES POWER...
-
Page 2: Important Safety Instructions
A. the power-supply cord or the plug has been soft, lint-free cloth. Do not use chemical solvents for This handbook is a guide to installing and using the A49, C49, P49 and P349 including 3. Heed all warnings. When a cart is used, use caution cleaning. -
Page 3: Table Of Contents
BD Device Mode ..................................... E-14 noise both the a A49, P49 and P349 are capable of the heat-sink, causing the amplifier to run hot. (The to do so may result in unwanted noise in the audio loudspeakers ............................E-15... -
Page 4: Power
Voltage select Phono earth terminal Record output Power inlet Voltage select For connecting your turntable The A49 is equipped with two Connect the correct Ensure that the voltage selected For connecting your turntable RECORD OUT is a line level output for... -
Page 5: P49 Connections
P349 connections connections Pre-amplifier output provides a copy of PRE OUT Unbalanced Trigger input Unbalanced Balanced XLR Balanced XLR the signal applied to the pre-amplifier inputs pre-amplifier inputs Trigger input pre-amplifier inputs Input switches pre-amplifier inputs sockets. Please note PRE IN TRIGGER IN allows the P349 to be remotely Use these sockets to connect... -
Page 6: A49/C49 Operation
(or BALANCE Balanced connections also have the ability to reject and ‘off’. If the A49/C49 is powered off with the display recommended for short cable runs. Connect to the on the CR902) to view the current setting, then use... -
Page 7: Switching On
Note that when both lights are out, the amplifier will In addition to changing the remote handset, the A49/ appear not to work, as all speakers are switched off. C49 unit must also be reconfigured to respond to the alternate codes. -
Page 8: Amp Device Mode
For example, to play track 15, in sequence. For example, to play track 15, Navigate menus contact your Arcam dealer who will be happy to help you. Rewind iPod press 1 , then press 5 . press 1 , then press 5 . -
Page 9: Bi-Amping
NOTE: Units can be interconnected via XLR or RCA. Bi-amping requires the use of two amplifiers per Both versions shown for illustration purposes only. ACCESSORY POWER channel. Normally, your A49 is used to drive the high- PHONO frequency (treble) speakers, while a power-amplifier GROUND PHONO... -
Page 10: Dual Mono
GAIN operates to protect the unit and the protection system Make sure GAIN 230 = 220 - 240V~ The A49/C49 is not muted (i.e. MT (mute) is not < < Ensure that the amplifier and remote are both set to... -
Page 11: A49 Specifications
NOTE: All specification values are typical unless otherwise stated. Continual improvement policy Continual improvement policy Arcam has a policy of continual improvement for its Arcam has a policy of continual improvement for its products. This means that designs and specifications products. -
Page 12: P49 Specifications
NOTE: All specification values are typical unless otherwise stated. Continual improvement policy Continual improvement policy Arcam has a policy of continual improvement for its Arcam has a policy of continual improvement for its products. This means that designs and specifications products. -
Page 13: Product Guarantee
Unit 15, Pembroke Avenue, Waterbeach, CAMBRIDGE, CB25 9QP, England or via www.arcam.co.uk. Problems? If your Arcam dealer is unable to answer any query regarding this or any other Arcam product please contact Arcam Customer Support at the above address and we will do our best to help you.