Wacom CLINIQ 21UX DTZ-2100 User Manual
  1. Manuals
  2. Brands
  3. Wacom Manuals
  4. Monitor
  5. CLINIQ 21UX DTZ-2100
  6. User manual
Wacom CLINIQ 21UX DTZ-2100 User Manual

Wacom CLINIQ 21UX DTZ-2100 User Manual

Interactive pen display
Hide thumbs
Table of Contents

Advertisement

Quick Links

DTZ-2100

User Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CLINIQ 21UX DTZ-2100 and is the answer not in the manual?

Questions and answers

Related Manuals for Wacom CLINIQ 21UX DTZ-2100

Summary of Contents for Wacom CLINIQ 21UX DTZ-2100

  • Page 1: User Manual

    DTZ-2100 User Manual...

  • Page 2: Safety Instructions

    Interactive Pen Display to malfunction. Where use is prohibited, power off Cintiq to prevent the possibility of it causing other electronic devices to malfunction. Wacom does not accept any liability for direct or consequential damages. HIGH VOLTAGE Do not open Cintiq. It has the risk of electric shock.
  • Page 3 Do not disassemble the Cintiq stand. Improper disassembly could result in physical injury or damage to the stand. In this case, Wacom shall have no responsibility to repair or replace the product. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

  • Page 4: Precautions On Use And Handling

    This product is for use with a DVI or VGA video card; using an inappropriate video card may damage Cintiq. ■ Do not disassemble the main unit or Grip Pen. This may cause the device to malfunction. In this case, Wacom ■...

  • Page 5: Introduction And Overview

    ■ Both stages require hardware and software installations. You can find information on using the Wacom Tablet Control Panel for customizing your tablet and pen settings in the online Help, located under the H menu in the Wacom Tablet Control Panel. See Customizing Cintiq--The Basics on page 13.

  • Page 6: Table Of Contents

    Installation LCD Display Installation Tablet Software Installation for Windows and Macintosh Customizing Cintiq – The Basics Opening the Wacom Tablet Control Panel Calibrating the Tablet Adjusting the LCD Monitor Factory Presets, Multi-sync, and User Settings Working with OSD (On Screen Display) Menu...

  • Page 7: Unpacking Cintiq

    Parts and Accessories VGA to DVI-I Adaptor DVI-D to DVI-I Adaptor* Power Supply Grip Pen and Pen Stand Power Cable Wacom Tablet Lock Brackets (1 pair) Driver CD and Screws (Qty 2) Userʼs Manual Felt Bearing Ring and (This manual) Felt Feet, Replacement Some package configurations include an additional CD containing bundled software applications.

  • Page 8: Unpacking And Mounting Cintiq Onto The Stand

    Unpacking and Mounting Cintiq onto the Stand 1.Unpack the stand. Incline Adjustment Levers CAUTION Before operate the Incline Adjustment Levers, please refer to Using the Stand section on page 18. Do not operate the incline adjustment levers when Cintiq is not mounted on the stand or the stand's rear feet are lifted;...

  • Page 9: Cintiq Component Functions

    Cintiq Component Functions Front View Power Lamp Status Lamp Lights green when power and video signals have properly been sup- plied to Cintiq. Turns orange or flashes when your computer goes Lights green when a pen switch is pressed, or when into power management mode.

  • Page 10: Rear View

    Rear View Plus Button ( ) Mius Button ( ) VGA/DVI Switch MENU Button ENTER Button Opens and closes the OSD* Use this switch to Opens and closes the Select sor exits an item in the menu correctly set Cintiq menu.
  • Page 11 InstallationI LCD Display Installation First install the display portion of Cintiq. Do not connect the USB or RS-232C connector until you procede to the Tablet Software Instalation for Windows and Macintosh . Turn off your computer. Connect the DVI-I connector to your computer. Check the video connector type of your computer and use the adap- tor as necessary.
  • Page 12 ARDWARE PDATE IZARD will display. Windows 2000: Insert the Wacom Tablet Driver CD. If the Wacom Tablet installation menu displays, close it. – Follow the prompts selecting the default options. – If a signing warning dialog box displays, click Y to accept the driver.

  • Page 13: Installation

    After connecting all cables of Cintiq, turn on Cintiq and your computer. Allow the operating system to fully load. Insert the Wacom Tablet Driver CD into the CD-ROM drive. The Wacom tablet software installer menu should au- tomatically display. If the menu does not display, double-click on the I icon (located on the CD).

  • Page 14: Customizing Cintiq - The Basics

    Customizing Cintiq – The Basics Opening the Wacom Tablet Control Panel The W Control Panel makes it easy to customize your Interactive Pen Display and the pen. ACOM ABLET To open the control panel: Windows: Click on the Windows S button and choose P .

  • Page 15: Calibrating The Tablet

    Customizing Cintiq – The Basics Calibrating the Tablet You will need to calibrate the tablet in order to line up the screen cursor position with the position of the pen on the In- teractive Pen Display. This is required to adjust for parallax caused by the clear plastic overlay. After setting the tablet in its working position, follow the procedure below to calibrate the tablet.
  • Page 16 LCD Display Adjustment and Functions Factory Presets, Multi-sync, and User Settings Factory Presets: To display images with the best quality (based on the incoming signal), Cintiq comes with a number of factory default standard display modes. Refer to page 27 for input signal specifications. Multi-sync: When connected as a VGA display, Cintiq attempts to automatically synchronize to the incoming signal.

  • Page 17: Adjusting The Lcd Monitor

    Adjusting the LCD Monitor Horizontal Center Menu Position (VGA only) Select to move the OSD Select to move the screen menu around the display. image left or right. To automatically adjust, use the RESET option. Vertical Center Reset (VGA only) Provides two op- Select to move the screen tions:...

  • Page 18: Adjusting Pitch And Phase

    Adjusting Pitch and Phase (VGA only) Some models of computer and graphics card may not allow the Auto Adjust to fully work when Cintiq is first connected. If the display does not fit the LCD panel border or some portion of text appears blurred, adjust pitch and phase by following the below procedure.

  • Page 19: Power Saving

    Adjusting the LCD Monitor HINT (Windows only): You can also adjust P and P in the closing Windows display. ITCH HASE If the pitch is not calibrated, vertical moire appears in the darkened area. And if the phase is not calibrated, the darkened area riffles. Power Saving Cintiq conforms to VESA and Energy Star power saving guidelines.

  • Page 20: Using The Grip Pen

    Using the Grip Pen Working with the Grip Pen Hold the pen as you would a pencil. Make sure the side switch is in a convenient location where you can press it with your thumb or forefinger, but won’t accidentally press it while drawing. Eraser Second Side Switch Side Switch...

  • Page 21: Using A Pen

    Using the Grip Pen Using a Pen Pointing and Selecting Move the pen above Cintiq Display screen to position the screen cursor. The cursor instantly jumps to the new location (absolute positioning). Press the pen tip on the Cintiq Display screen to make a selection.
  • Page 22 Working with the Cintiq StandI Adjusting Tilt The stand allows Cintiq’s tilt to be adjusted to any angle between 77 and 20 degrees from vertical. To adjust the incline, from the front of Cintiq grasp the Interactive Pen Display on the left and right side at approximately the same height as the Cintiq stand adjustment levers.

  • Page 23: Working With The Cintiq Stand

    Working with the Cintiq Stand Rotating Cintiq Rotating freely : If you remove the lock brackets and tilt the Cintiq more than 50 degrees, the main unit can be freely rotated on the stand between +180 and -180 degrees without touching the desktop. In this position, Cintiq emulates a traditional animator’ s table and gives you the freedom to rotate the display unit to any angle for the greatest comfort and accuracy of stroke while drawing or editing images.

  • Page 24: Using An Alternate Mount Or Stand

    Using an Alternate Mount or Stand To use Cintiq in an installation that requires the use of an alternate mounting platform, you will need to obtain a VESA conforming mount arm or stand which has: A 100 x 100 mm square screw hole pattern to attach the Cintiq main unit ■...

  • Page 25: Caring For Your Cintiq

    Caring for Cintiq Cleaning To clean the Cintiq casing, use a soft cloth with mild detergent (such as dish washing liquid) diluted with water. Do not use paint thinner, benzine, alcohol, or other organic solvents to clean Cintiq casing or pen. To clean the display screen, use an antistatic cloth or slightly moisten damp cloth.

  • Page 26: Display Troubleshooting

    If you encounter problems with Cintiq display, refer to the following tables. Your problem may be described here, and you can try the solution offered. For the problems regarding tablet or pen, refer to the Troubleshooting chapter in the online Help that can be accessed from the Wacom Tablet control panel. Genera Problem Hint The input signal frequency is incorrectly set or not compatible with Cintiq.
  • Page 27 Display Troubleshooting General Problem Hint The image appears multiple times on the Do not extend the video cable. Do not use an input selector switch box. display. The color white does not display as white. Be sure the Cintiq color profile has been installed and is selected as the profile for use ■...

  • Page 28: Specifications

    TFT display, and some panels may exhibit a certain number of pixels that show an incorrect color. Wacom quality standards are based on internationally accepted standards for LCD displays. Wacom requires more than 99.999% of the 1,310,720 pixels on each Cintiq 21UX to function perfectly, and does not allow any pixel to be always white or always black.

  • Page 29: Power Adaptor

    Specifications Tablet Reading technology: Electromagnetic give and receive method Active area: 432 x 324mm Resolution: 20 lpmm (0.05mm) max. Accuracy: +/-0.5mm, four corners ( 7 mm wide, 25 mm long from each corner of four "L" shaped areas) to be +/-1.0mm Maximum reading height: Maximum report rate: 205 points/sec., max.
  • Page 30 Grip Pen (Model UP-911E) Pressure levels: Pen tip travel: 0.1 mm (0.004 in) or less Eraser tip travel: 2 mm (0.08 in), approximately Physical dimensions, weight: 14.0 x 149.0 mm, 16g Side switch type: Rocker switch -- Pen Accessories Extra nib: PSI-A007 Pen holder: PST-A026-03...

  • Page 31: Appendix

    Copyright © WACOM Company, Limited, 2002 All rights reserved. No part of this manual may be reproduced except for your express personal use. Wacom reserves the right to revise this publication without obligation to provide notification of such changes. Wacom does its best to provide current and accurate information in this manual. However, Wacom reserves the right to change any specifications and product configurations at its discretion, without prior notice and without obligation to include such changes in this...

Table of Contents