Genie Z-34/22n Operator's Manual
Hide thumbs Also See for Z-34/22n:

Advertisement

800-610-4101
ActionRental.com
Incorrect operation can result from use of this manual on machines that have not been updated
according to Genie Campaign Bulletin 070001. Death or Serious Injury can result.
This manual only applies to machines that have been updated according to Genie Campaign
Bulletin 070001. Contact Genie Industries for information on this bulletin.
Technical
Publications
Z-34 22
Z-34 22
Operator's
Manual
First Edition, Sixth Printing
Part No. 36539

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Z-34/22n and is the answer not in the manual?

Questions and answers

Summary of Contents for Genie Z-34/22n

  • Page 1 Incorrect operation can result from use of this manual on machines that have not been updated according to Genie Campaign Bulletin 070001. Death or Serious Injury can result. This manual only applies to machines that have been updated according to Genie Campaign Bulletin 070001. Contact Genie Industries for information on this bulletin.
  • Page 2: Table Of Contents

    Work Place Inspection ..........16 Operating Instructions ..........17 Transport Instructions ..........22 ® Decals ..............24 Copyright © 1996 by Genie Industries Specifications ............27 First Edition: Sixth Printing, June 2007 Genie® is a registered trademark of Genie Industries. Registered 2009987 These machines comply with ANSI/SIA 92.5-1992.
  • Page 3: Safety Rules

    You read, understand and obey: Manufacturer's instructions and safety rules—safety and operator's manuals and machine decals employer's safety rules and worksite regulations applicable governmental regulations You are properly trained to safely operate the machine. Part No. 36539 Genie Z-34/22 & Genie Z-34/22N...
  • Page 4 Do not operate the machine during lightning or storms. Do not use the machine as a ground for welding. Genie Z-34/22 & Genie Z-34/22N Part No. 36539...
  • Page 5 Do not use machine on a moving or mobile surface Note: Slope rating is subject to ground conditions or vehicle. and adequate traction. Be sure all tires are in good condition and lug nuts are properly tightened. Part No. 36539 Genie Z-34/22 & Genie Z-34/22N...
  • Page 6 Be aware of limited sight distance and blind spots when driving or operating. Be aware of boom position when rotating turntable. Machine must be on level surface or secured before releasing brakes. Genie Z-34/22 & Genie Z-34/22N Part No. 36539...
  • Page 7 Do not operate a boom in the path of any crane unless the controls of the crane have been locked out and/or precautions have been taken to prevent any potential collision. Part No. 36539 Genie Z-34/22 & Genie Z-34/22N...
  • Page 8 Be sure all maintenance has been performed as specified in this manual and the Genie Z-34/22 & Genie Z-34/22N Service Manual. Be sure all decals are in place and legible. Be sure safety and operator’s manuals are complete, legible and in the storage container located on the platform.
  • Page 9 Use a forklift to remove or install the battery the entire charging pack(s). cycle. Do not contact the battery terminals or the cable clamps with tools that may cause sparks. Part No. 36539 Genie Z-34/22 & Genie Z-34/22N...
  • Page 10: Controls

    6 Emergency Stop button 15 Secondary boom up/down switch 7 Platform rotate switch 16 Primary boom up/down switch 8 Battery charge indicator 17 Turntable rotate switch 9 Boom/Drive function select switch (option) Genie Z-34/22 & Genie Z-34/22N Part No. 36539...
  • Page 11 Boom extend/retract switch 15A breaker for electrical circuits Platform rotate switch Auxiliary power switch with cover Platform level switch Hour meter Jib boom up/down switch Key switch for platform/off/ground selection Secondary boom up/down switch Part No. 36539 Genie Z-34/22 & Genie Z-34/22N...
  • Page 12: Pre-Operation Inspection

    5 Only use the machine as it was intended. the function tests. Scheduled maintenance inspections shall be performed by qualified service technicians, according to the manufacturer's specifications and the requirements listed in the responsibilities manuals. Genie Z-34/22 & Genie Z-34/22N Part No. 36539...
  • Page 13 ! Be sure that both battery packs are in place, latched and properly connected. ! After you complete your inspection, be sure that all compartment covers are in place and latched. Part No. 36539 Genie Z-34/22 & Genie Z-34/22N...
  • Page 14: Function Tests

    3 Always perform function tests prior to use. Know and understand the function tests before going on to the next section. 4 Inspect the work place. 5 Only use the machine as it was intended. Genie Z-34/22 & Genie Z-34/22N Part No. 36539...
  • Page 15 The descent alarm power, test each function (if equipped) should sound while boom is through a partial cycle. lowering. Result: All boom functions should operate. 13 Turn the key switch to platform control. Part No. 36539 Genie Z-34/22 & Genie Z-34/22N...
  • Page 16 Result: The travel/brake release alarm should sound. The machine should move in the direction that the yellow arrow points on the drive chassis, then come to an abrupt stop. Genie Z-34/22 & Genie Z-34/22N Part No. 36539...
  • Page 17 39 Repair any malfunctions before operating the range shown. machine. 34 Move the drive control handle off center. Result: The drive function should not operate. Part No. 36539 Genie Z-34/22 & Genie Z-34/22N...
  • Page 18: Work Place Inspection

    It is the operator's responsibility to read and remember the work place hazards, then watch for and avoid them while moving, setting up and operating the machine. Genie Z-34/22 & Genie Z-34/22N Part No. 36539...
  • Page 19: Operating Instructions

    That means every new operator should perform a pre-operation inspection, function tests, and a work place inspection before using the machine. Part No. 36539 Genie Z-34/22 & Genie Z-34/22N...
  • Page 20 2 Press down the foot switch. is raised or extended. 3 Move the appropriate toggle switch according to Battery condition will affect the ability of the the markings on the control panel. machine to climb a slope. Genie Z-34/22 & Genie Z-34/22N Part No. 36539...
  • Page 21 Lay the piece of wood on the slope. At the downhill end, lay the level on the top edge of the piece of wood and lift the end until the piece of wood is level. Part No. 36539 Genie Z-34/22 & Genie Z-34/22N...
  • Page 22 Emergency Stop button. If machine speed exceeds 3 mph / 4.8 km/h (walking pace), immediately stop the machine. Genie Z-34/22 & Genie Z-34/22N Part No. 36539...
  • Page 23 3 Rotate the turntable so that the boom is between the non-steering wheels. 4 Turn the key switch to the off position and remove the key to secure from unauthorized use. 5 Chock the wheels. 6 Charge the batteries. Part No. 36539 Genie Z-34/22 & Genie Z-34/22N...
  • Page 24: Transport Instructions

    (see Specifications , page 27). Machine must be on level surface or secured before releasing brakes. Always use a winch to load and unload a machine from a transport vehicle. Genie Z-34/22 & Genie Z-34/22N Part No. 36539...
  • Page 25 1 Chock wheels to prevent machine from rolling. 2 Apply the non-steer wheel brakes by turning over torque hub disconnect caps (see below). Towing the Genie Z-34/22 or the Genie Z-34/22N is not recommended. If the machine must be towed, do not exceed 2 mph (3.2 km/h).
  • Page 26: Decals

    Genie Z-34/22N Genie Z-34/22 45 114330 21 28161 Safety Rules Warning - Crush Hazard 22 28157 Label - Dexron Shading indicates decal is hidden from view, i.e. 23 37095 under covers “Z” Genie Z-34/22 & Genie Z-34/22N Part No. 36539...
  • Page 27 First Edition Operator's Manual 800-610-4101 ActionRental.com D ECALS Ground Controls Side Power Unit Side Part No. 36539 Genie Z-34/22 & Genie Z-34/22N...
  • Page 28 Operator's Manual First Edition 800-610-4101 ActionRental.com DECALS Turntable - Boom Storage End Platform Turntable - Boom Pivot End Drive Chassis - Top Genie Z-34/22 & Genie Z-34/22N Part No. 36539...
  • Page 29: Specifications

    Side slope (11°) Note: Slope rating is subject to ground conditions and adequate traction. Continuous improvement of our products is a Genie policy. Product specifications are subject to change without notice or obligation. Part No. 36539 Genie Z-34/22 & Genie Z-34/22N...
  • Page 30 Side slope (11°) Note: Slope rating is subject to ground conditions and adequate traction. Continuous improvement of our products is a Genie policy. Product specifications are subject to change without notice or obligation. Genie Z-34/22 & Genie Z-34/22N Part No. 36539...
  • Page 31 Genie Denmark Genie U.K. Phone: 82 2 558 7267 Phone: 45 6612 5544 Phone: 44 1636 614700 Genie Australia Pty Ltd. Fax: 82 2 558 3910 Fax: 45 6612 5530 Fax: 44 1636 611090 Phone: 1 61 7 3375 1660...

This manual is also suitable for:

Z-34/22

Table of Contents