Page of 10
   
HPE 5400R zl2 Switches Quick
Setup Guide and Safety/Regulatory
Information
*5200-2721*
Part Number: 5200-2721
Published: October 2016
Edition: 2, Printed in Singapore

Advertising

   Also See for HP 5400R zl2

   Related Manuals for HP 5400R zl2

   Summary of Contents for HP 5400R zl2

  • Page 1

    HPE 5400R zl2 Switches Quick Setup Guide and Safety/Regulatory Information *5200-2721* Part Number: 5200-2721 Published: October 2016 Edition: 2, Printed in Singapore...

  • Page 2

    The drawings used in this document are for illustration purposes only and may not exactly match your particular switch. For complete installation instructions, see the HPE 5400R zl2 Installation and Getting Started Guide on the Hewlett Packard Enterprise Networking Web site at: http://www.hpe.com/ networking/support Auto search on “zl modules,”...

  • Page 3

    While installing multiple power supplies in a switch, Hewlett Packard Enterprise recommends that all power supplies are the same models. See the HPE 5400R zl2 Installation and Getting Started Guide for selecting the correct power cord to use with the supply.

  • Page 4

    1. Grounding Lug Mounting Holes 2. Power Supply Slots Software version For the latest software version, go to: http://www.hpe.com/networking/support Installation notes Transceiver operation notes Revision “B” or later SFP transceivers only. This product requires revision “B” or later mini-GBICs or SFP transceivers (product number ends with the letter “B” or later, for example J4858B or J4859C).

  • Page 5

    (The switch always reboots from the startup-configuration file.) One of the features of your 5400R zl2 switch is the ability to “hot swap” the switch modules. You can install, exchange, or remove modules after the switch has been powered on. Whenever a module is installed during this process, it is initialized and tested for correct operation.

  • Page 6

    no precautions are required. Use one of the following installation methods while performing an installation, when using more than four power cords: ◦ Using normal pluggable cords: – Place the equipment in a restricted access area such as a locked closet or key card access room, the access for which is granted only for qualified or service personnel.

  • Page 7

    Allow at least three inches of space around the sides and back of the switch to make sure the air flow for the switch is not restricted. Regulatory information WARNING! Do not wall-mount any of the 5400R zl2 switches or bundles. HPE 5406R zl2 (J9821A) and 5412R zl2 Switches Applicable Products (J9822A) including all bundles Environmental Operating Temperature: 0°C to 45°C (32°F to 113°F)

  • Page 8

    Table 1 HPE 5400R zl2 Power Supplies Electrical J9828A J9829A J9830B Main AC voltage: 100 -127 volts; 200 - 110 -127 volts; 200 - 115-127; 200-240 115-127; 200-240 240 volts 240 volts volts volts Maximum current: 8.5; 4.3 A max 12;...

  • Page 9

    Country/Region J9829A Power Supply Cable Taiwan 8121-1511 Israel 8121-1478 Argentina 8121-1481 Brazil 8121-1474 Chile 8121-1477 North America 110V 8121-0914 Country/Region J9828A Power Supply Cable Australia 8121-0834 China 8120-8707 Europe/South Korea 8120-6811 Japan 8120-4753 Thailand/Philippines 8121-0668 India 8121-0780 Denmark 8120-6814 Switzerland 8120-6815 United Kingdom/Hong Kong/Singapore/Malaysia 8120-6809...

  • Page 10

    Battery Statements ATTENTION ll y a danger d'explosion s'il y a remplacement incorrect de la batterie. Remplacer uniquement avec une batterie du même type ou d'un type équivalent recommandé par le constructeur. Mettre au rebut les batteries usagées conformément aux instructions du fabricant. ATTENTION The battery supplied on the management module with this product may contain perchlorate material.

Comments to this Manuals

Symbols: 0
Latest comments: