1. Manuals
  2. Brands
  3. NETGEAR Manuals
  4. Security Camera
  5. Arlo
  6. Quick start manual

NETGEAR arlo Quick Start Manual

Hide thumbs Also See for arlo:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual, Quick Start Manual
Quick Start Guide
Beta
1

Advertisement

Table of Contents
loading

Related Manuals for NETGEAR arlo

Summary of Contents for NETGEAR arlo

  • Page 1 Quick Start Guide Beta...
  • Page 2 Welcome Thank you for choosing Arlo. Getting started is easy.

  • Page 3: What's Included

    What’s included Base Station Base station Ethernet cable Magnetic wall Mounting power adapter mounts screws 100% wireless Lithium 123 batteries camera(s) (number of batteries varies with number of cameras)

  • Page 4: Connect Your Base Station To The Internet

    Connect Your Base Station to the Internet Connect the base station to your router Connect the AC adapter to your base using an Ethernet cable. station and plug it in.
  • Page 5 Turn the base station on by pressing the The power LED on the front of the On-Off button. base station should turn green in about one minute. (If this doesn’t happen, please refer to http://support.netgear.com for troubleshooting tips.)
  • Page 6 Get the App For the best experience, download the Arlo app for your smartphone by scanning the QR code below or searching for “Arlo” in the app store.

  • Page 7: Get An Account

    Get an Account Launch the app from your smartphone and click the New System Setup button. Follow the on-screen instructions. Or go to https://arlobeta.netgear.com/ follow the on-screen instructions.
  • Page 8 Set Up and Sync Your Cameras Insert batteries • Unlock the battery compartment by sliding and holding the latch. • Then slide the battery door back and lift it up to open the compartment. • Insert the batteries as shown, and then close the battery door.
  • Page 9 Sync your cameras with the base station Bring the camera within 12 inches of the base station. 12”...
  • Page 10 Sync your cameras with the base station (cont’d) Press the Sync button on the side of the Press the Sync button on top of base station. the camera. Wait for the sync status LED to blink green.
  • Page 11 A blue LED on the camera will blink for ten The camera LED on the base station seconds to confirm sync. will turn solid green once the camera is synced. The camera is ready for viewing. Note: If the sync procedure is not completed within 60 seconds, press the Sync...

  • Page 12: Place Or Mount Your Cameras

    Locate a spot for your camera You can place your camera on a shelf or other flat surface, or you can mount it to the wall. Tip: Use the Arlo app in ‘Position Mode’ (found in Camera Settings) to help aim the camera.
  • Page 13 To mount your camera to the wall: Fasten the mounting screw into the wall, and hang the magnetic mount from the screw. If you’re mounting this to drywall, be sure to use the drywall plastic anchors that have been provided. Tip: You can also use double-sided tape instead of screws.

  • Page 14: You're Done

    You’re Done! Congratulations! Your Arlo System is set up and ready to go! If you would like to view useful tutorial videos, find troubleshooting tips, or get support, please visit http://support.netgear.com or call (US only) 1-888-NETGEAR.

  • Page 15: Led Guide

    LED Guide Power Internet Camera Home Network Green Green Green Green Green The base station The base station Cameras are Smart devices A USB device is powered on. is connected to connected to the are connected. is detected. the internet. base station.
  • Page 16 ©2014 NETGEAR, Inc. NETGEAR, the NETGEAR Logo, and Arlo are trademarks of NETGEAR, Inc. 350 East Plumeria Drive San Jose, CA 95134, USA Beta August 2014...

Table of Contents