Advertisement
Quick Links
VERONA CRIB
Thank you for selecting a ducduc for nod product.
Please check contents against the components list in
these instructions. Also, please ensure there was no
damage that may have occurred in shipping. if any
components are missing or you find any damage,
please contact The Land of Nod at 800-933-9904
before continuing.
Read all the instructions before use of the CRIB.
Please remember to securely tighten all bolts and
fasteners and periodically check to make sure every
component is properly and securely in place.
Pay close attention to the safety warnings in these
instructions and on CRIB labels.
A minimum of two people is required to safely
assemble and move the CRIB. Do not attempt to
move this CRIB alone - dragging or sliding it across
the floor may cause structural damage.
CAUTION:
used in this CRIB must be
at least 27 1/4 inches by 51
5/8 inches with a thickness
not exceeding 6 inches.
Keep instructions for future use.
Any mattress
Advertisement
Related Manuals for ducduc Verona
Summary of Contents for ducduc Verona
- Page 1 Thank you for selecting a ducduc for nod product. Please check contents against the components list in these instructions. Also, please ensure there was no damage that may have occurred in shipping. if any components are missing or you find any damage, please contact The Land of Nod at 800-933-9904 before continuing.
- Page 3 Lay SIDE PANEL down with holes facing up. Attach CRIB LEG to SIDE PANEL with one RAIL CONNECTOR BOLT LOCKING WASHER , and REGULAR WASHER . Tighten with ALLEN WRENCH REPEAT FOR ACCENT PANEL Align the BASE so that the sticker “Bottom” is facing the floor. The side of BASE with only two corner holes should be aligned against SIDE PANEL as shown.
- Page 4 Place SIDE RAIL onto BASE with rail connector holes facing SIDE PANEL . Attach ACCENT PANEL to crib SIDE RAIL and secure in place with two BASE CONNECTOR BOLTS , LOCKING WASHERS , and REGULAR WASHERS as shown below. Tighten all bolts with ALLEN WRENCH Back accent panel...
- Page 5 Place END RAIL onto BASE with mattress support holes facing the bottom and inside of crib. Secure END PANEL to BASE with BASE CONNECTOR BOLTS , LOCKING WASHERS , and REGULAR WASHERS from underneath as shown below. Place other END RAIL on the opposite side with mattress support holes facing the bottom and inside of crib.
- Page 6 Line up the rail connector holes on SIDE PANEL with the rail connector holes on the END RAILS Attach LOCKING WASHERS and REGULAR WASHERS to RAIL CONNECTOR BOLTS insert and slightly tighten the four RAIL CONNECTOR BOLTS with ALLEN WRENCH rail connector holes Back rail connector holes...
- Page 7 Tighten bolts all the way. The MATTRESS SUPPORT PANEL may be installed in one of four positions. See the four different mattress support holes in each corner of the CRIB. First, select the desired mattress height. Then, unscrew the MATTRESS SUPPORT PIN from each MATTRESS SUPPORT BOLT .
- Page 8 Attach one LOCKING WASHER and one REGULAR WASHER on top of each MATTRESS SUPPORT PIN . Secure and tighten each of the four MATTRESS SUPPORT BOLTS to each of the four MATTRESS SUPPORT PINS . Use SCREWDRIVER tighten securely. Press firmly in center of MATTRESS SUPPORT PANEL to ensure proper placement.
- Page 9 operation Th e ma ttress h eig ht s ho uld b e low e re d a s yo u r ba b y g ro ws t o e n s u re t h a t h e/s he do es no t clim b o ut o f th e C RIB . W h e n c h il d i s a b le t o pu ll t o a st an d in g po si tio n, s et m at tres s t o l owe s t po s it i o n a n d re m o ve bu mb e r p a ds , large to y s, a nd o th er o b jec ts th a t c o ul d s e r ve a s s te ps fo r c l im b in g o u t .
- Page 10 Securely tighten loose bolts and other fasteners. DO NOT use crib if any parts are missing, damaged or broken. Contact ducduc for replacement parts and instructional literature if needed. DO NOT substitute parts.
Need help?
Do you have a question about the Verona and is the answer not in the manual?
Questions and answers