Advertisement
Quick Links
Thank you for selecting a ducduc for nod product.
Please check contents against the components list in
these instructions. Also, please ensure there was no
damage that may have occurred in shipping. If any
components are missing or you find any damage,
please contact The Land of Nod at 800-933-9904
before continuing.
Read all the instructions before use.
VERONA BED
PLEASE REMEMBER TO SECURELY TIGHTEN ALL
BOLTS AND FASTENERS AND PERIODICALLY
CONVERSION KIT
CHECK TO MAKE SURE EVERY COMPONENT IS
PROPERLY AND SECURELY IN PLACE.
A minimum of two people is required to safely
assemble and move the bed.
DO NOT ATTEMPT TO MOVE THIS BED ALONE -
DRAGGING OR SLIDING IT ACROSS A FLOOR MAY
CAUSE STRUCTURAL DAMAGE.
USE MATTRESS WHICH IS MAX 75" LONG, AND
53"-54" WIDE.
MINIMUM AGE FOR USE IS 3+ YEARS.
Keep instructions for future use.
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for ducduc VERONA
Summary of Contents for ducduc VERONA
- Page 1 Thank you for selecting a ducduc for nod product. Please check contents against the components list in these instructions. Also, please ensure there was no damage that may have occurred in shipping. If any components are missing or you find any damage, please contact The Land of Nod at 800-933-9904 before continuing.
- Page 2 components pictures are not drawn to scale MATTRESS RAIL (RIGHT) HEADBOARD (not included) FOOT BRACKET FOOTBOARD (not included) MATTRESS RAIL (LEFT) SCREWDRIVER BED RAIL CONNECTOR BOLT (35mm) (not included) (not included) MATTRESS SLAT ROLL 1 1/4” SCREWS CAP AND FOOT BRACKET BOLT - (7/16”) LOCKING WASHER - (1/4”) REGULAR WASHER - 1/4”) ALLEN WRENCH...
- Page 3 assembly Remove MATTRESS SUPPORT PANEL by unscrewing each of the four MATTRESS SUPPORT BOLTS w ith SCREWDRIVER mattress support bolts mattress support panel Remove both END RAILS from HEADBOARD by removing four RAIL CONNECTOR BOLTS two BASE CONNECTOR BOLTS, LOCKING WASHERS , and REGULAR WASHERS from the headboard connector holes and base connector holes with ALLEN WRENCH end rails rail connector bolts...
-
Page 4: Base Frame
This step includes removing base frame, so have a second person available to hold the crib when these parts are removed to prevent the crib from falling. Alternatively, perform this step with the crib on its back. Remove BASE FRAME from HEAD BOARD and FOOT BOARD by removing the four BASE CON- NECTOR BOLTS, LOCKING WASHERS, and REGULAR WASHERS from the accent panel connector... - Page 5 Lay FOOTBOARD face down and attach each MATTRESS RAILS & vertically to FOOTBOARD using four BED RAIL BOLTS , LOCKING WASHERS , and REGULAR WASHERS . Tighten with ALLEN WRENCH . Return bed to horizontal position. ATTACH FOOT BRACKET to MATTRESS RAILS &...
- Page 6 Place MATTRESS SLAT ROLL onto MATTRESS RAILS & Install four SCREWS into pre-drilled holes in slats. Tighten scews using SCREWDRIVER...
- Page 7 Attach two CAP BOLTS to each side of HEADBOARD . Insert four plastic CAPS into CAP BOLTS...
- Page 8 Remove SIDE RAIL from FOOTBOARD by removing two RAIL CONNECTOR BOLTS, three BASE CONNECTOR BOLTS, LOCKING WASHERS, and REGULAR WASHERS from the footboard connector holes and base connector holes with ALLEN WRENCH rail connector bolts side rails base connector bolts...
-
Page 9: Operation
operation Periodically check to make sure every component is properly and securely in place and all bolts and fasteners are tight. Do not scratch or chip the finish. Do not use abrasive chemicals for cleaning. Clean with mild soap on a soft rag. Rinse and dry thoroughly. If you ever refinish this furniture, be sure to use only a non-toxic finish specified for children’s furniture.
Need help?
Do you have a question about the VERONA and is the answer not in the manual?
Questions and answers