Charging The Device; Tips For Charging The Device; Device Care; Troubleshooting - Garmin VARIA UT800 Owner's Manual

Intensity Mode LED Luminous Flux
Night flash 100 to 300 lm
Day flash 700 lm

Charging the Device

This device contains a lithium-ion battery. See the Important
Safety and Product Information guide in the product box for
product warnings and other important information.
To prevent corrosion, thoroughly dry the USB port, the weather
cap, and the surrounding area before charging or connecting to
a computer.
NOTE: The device does not charge when outside the approved
temperature range (Specifications, page
1
Pull up the weather cap from the USB port.
2
Plug the small end of the USB cable into the USB port on the
device.
3
Plug the large end of the USB cable into a power source,
such as a USB wall charger or a computer USB port.
4
Charge the device completely.
The status LED flashes green while charging. The status LED is
solid green when charging is complete.

Tips for Charging the Device

• Connect the charger securely to the device.
You can charge the device by plugging the USB cable into a
Garmin approved AC adapter with a standard wall outlet or a
USB port on your computer. Charging a fully depleted battery
takes about 6 hours using a computer and 4 hours using an
AC power source.
• Remove the charger from the device when the status LED is
solid green.
• View the remaining battery life
connections screen (Viewing the Connections Screen,
page 2).

Device Care

Do not store the device where prolonged exposure to extreme
temperatures can occur, because it can cause permanent
damage.
Avoid chemical cleaners, solvents, and insect repellents that can
damage plastic components and finishes.
Secure the weather cap tightly to prevent damage to the USB
port.
Cleaning the Device
1 Wipe the device using a cloth dampened with a mild
detergent solution.
2
Wipe it dry.
4
Battery Life
Up to 6 hr.
Up to 25 hr.
WARNING
NOTICE
3).
on your Edge device
NOTICE
After cleaning, allow the device to dry completely.

Troubleshooting

Resetting the Device

You can reset the device if it stops responding.
Hold the device key for 8 seconds until all the LEDs turn off.
Resetting deletes the pairing connections from the device.

Thermal Safety Shutdown

To prevent overheating, the Varia device may turn off when
operated at a high intensity in warm, stagnant air. The status
LED is red until the device cools down. You should use the
device outdoors.

Low Temperature Battery Conservation

To extend the battery life of the device, the Varia device is
limited to medium, low, and flash modes when used in very cold
temperatures.

Product Updates

On your computer, install Garmin Express
/express).
This provides easy access to these services for Garmin devices:
• Software updates
• Product registration

Getting More Information

• Go to www.garmin.com/intosports.
• Go to www.garmin.com/learningcenter.
• Go to http://buy.garmin.com, or contact your Garmin dealer
for information about optional accessories and replacement
parts.

Other Compatible Devices

Pairing Your Bike Light with Your Edge 1000

1
Bring the Edge device within range (1 m) of the sensor.
NOTE: Stay 10 m (33 ft.) away from other ANT+ bike lights
while pairing.
2
Turn on the Edge device.
3 From the home screen, select
Search All.
4
While the headlight is turned off, hold the Varia device key for
2 seconds to enter pairing mode.
The status LED flashes purple.
5
Select your sensor.
When the sensor is paired with your Edge device, the status
icon appears solid on the connections page.

Pairing the Remote with Your Varia Device

The first time you connect the Varia remote to your Varia device,
you must pair the remote with your device.
1
Bring the remote within 1 m (3 ft.) of the device.
NOTE: You must stay 10 m (33 ft.) away from other ANT+
sensors while pairing.
2
While the headlight is turned off, hold the Varia device key for
2 seconds to enter pairing mode.
The status LED flashes purple.
(www.garmin.com
™
> Sensors > Add Sensor >
Troubleshooting