Garmin VARIA UT800 Owner's Manual
  1. Manuals
  2. Brands
  3. Garmin Manuals
  4. Flashlight
  5. VARIA UT800
  6. Owner's manual

Garmin VARIA UT800 Owner's Manual

Hide thumbs Also See for VARIA UT800:
Table of Contents

Advertisement

Quick Links

Download this manual
VARIA
UT800
™
Owner's Manual

Advertisement

Table of Contents
loading

Related Manuals for Garmin VARIA UT800

Summary of Contents for Garmin VARIA UT800

  • Page 1 VARIA UT800 ™ Owner’s Manual...
  • Page 2 © 2017 Garmin Ltd. or its subsidiaries All rights reserved. Under the copyright laws, this manual may not be copied, in whole or in part, without the written consent of Garmin. Garmin reserves the right to change or improve its products and to make changes in the content of this manual without obligation to notify any person or organization of such changes or improvements. Go to www.garmin.com...

  • Page 3: Table Of Contents

    Table of Contents Introduction........1 Installing the Out-Front Mount....2 Installing the Helmet Mount....5 Device Overview........6 Turning On the Device......6 Bike Light Status LEDs......6 Device Settings........ 6 Pairing Your Bike Light with Your Edge 830 or 1030..........7 Customizing Headlight Settings with Your Edge Device........

  • Page 5: Introduction

    Introduction WARNING See the Important Safety and Product Information guide in the product box for product warnings and other important information. The device is intended for outdoor use. Without proper airflow during use, the device may become hot. Handle with care. Introduction...

  • Page 6: Installing The Out-Front Mount

    You can use the out-front mount to install the headlight and your Edge ® device. Garmin recommends that you adjust the mount for the Edge viewing angle before you install and adjust the headlight angle. 1 Select a secure location to mount the Edge device and headlight where they do not interfere with the safe operation of your bike.
  • Page 7 9 Insert the screw , and hand tighten. 10 Align the notches of the quarter-turn adapter with the tabs on the bottom of the mount. 11 Press up slightly, and turn the adapter counterclockwise until it locks into place. 12 Adjust the headlight angle so it is parallel to the ground, and use the 4 mm hex key to tighten the screw. Introduction...
  • Page 8 NOTE: You should check the tightness of the screw periodically. Introduction...

  • Page 9: Installing The Helmet Mount

    Installing the Helmet Mount 1 Select a secure location to mount the headlight where it does not interfere with the safety and comfort of your helmet. 2 Attach the mount using both straps. 3 Lock the straps by pressing down the clasp. 4 Connect the adapter to the headlight.

  • Page 10: Device Overview

    The lever must be flush with the base. 9 Adjust the headlight angle, and use the 4 mm hex key to tighten the screw. NOTE: You should check the tightness of the screw periodically. Device Overview Hold for 1 sec. to turn the device on. Hold for 2 sec.

  • Page 11: Pairing Your Bike Light With Your Edge 830 Or 1030

    Pairing Your Bike Light with Your Edge 830 or 1030 1 Bring the Edge device within range (1 m) of the sensor. NOTE: Stay 10 m (33 ft.) away from other ANT+ ® bike lights while pairing. 2 Turn on the Edge device. 3 Select >...

  • Page 12: Automatic Beam Intensity

    Light Mode Settings From the Sensors menu, select Lights > Network Options > Light Mode. Auto: Automatically adjusts the light intensity and light mode based on the ambient light and time of day. High Visibility: Sets the light intensity to flash mode or the brightest setting available. Trail: Automatically adjusts the light intensity and light mode based on the ambient light and time of day.

  • Page 13: Device Information

    100 to 300 lm Up to 6 hr. Day flash 700 lm Up to 25 hr. The device withstands incidental exposure to water of up to 1 m for up to 30 min. For more information, go to www.garmin.com/waterrating. Device Information...

  • Page 14: Charging The Device

    • Connect the charger securely to the device. You can charge the device by plugging the USB cable into a Garmin approved AC adapter with a standard wall outlet or a USB port on your computer. Charging a fully depleted battery takes about 6 hours using a computer and 4 hours using an AC power source.

  • Page 15: Troubleshooting

    This provides easy access to these services for Garmin devices: • Software updates • Product registration Getting More Information • Go to support.garmin.com for additional manuals, articles, and software updates. • Go to buy.garmin.com, or contact your Garmin dealer for information about optional accessories and replacement parts. Troubleshooting...

  • Page 16: Other Compatible Devices

    Other Compatible Devices Pairing Your Bike Light with Another Edge Device 1 Bring the Edge device within range (1 m) of the sensor. NOTE: Stay 10 m (33 ft.) away from other ANT+ bike lights while pairing. 2 Turn on the Edge device. 3 From the Sensors menu, select Add Sensor >...

  • Page 17: Index

    ANT+ sensors 7 battery 9, 11 charging 10 brightness 8, 11 charging 10 cleaning the device 11 customizing the device 6 device, care 10 Edge 6–8, 12 Garmin Express, updating software 11 GPS, signal 7 installing 2, 5 keys 6 mounting the device 2, 5 pairing 7, 12 remote control 12 remote control, pairing 12 resetting, device 11...
  • Page 18 July 2021 GUID-FD3E6E17-4A64-4236-8D3B-510A13E097E6 v3...

Table of Contents