Sony WX-7700MDX Service Manual page 9

3
4
*
SUBWOOFER OUT
(MONO)
* 1
RCA pin cord
BUS CONTROL IN
1
Left
Right
Left
Right
4 A
TOYOTA/MITSUBISHI
This illustration is for TOYOTA cars.
1 or 2
max. size 5 × 8 mm
Bracket
Existing parts supplied with your car
Precautions Frequency select switch
The AM (FM) tuning interval is factory-set to the
• Choose the installation location carefully so
9 k (50 k) position. If the frequency allocation
that the unit will not interfere with normal
system of your country is based on 10 kHz (200
driving operations.
kHz) interval, set the switch on the bottom of
• Avoid installing the unit in areas subject to
the unit to the 10 k (200 k) position before
dust, dirt, excessive vibration, or high
making connections.
temperatures, such as in direct sunlight or near
heater ducts. After the frequency select switch is set, you must
• Use only the supplied mounting hardware for press the reset button to reset the unit.
a safe and secure installation.
To open/close the front panel smoothly, to insert/
eject a disc easily, and especially to drive safely, a
certain distance between the front panel and the
shift lever is necessary. The necessary distance
differs, depending on the shift lever position of
your car. Before installing the unit, choose the
installation location carefully so that you can
drive safely.
88 mm
Shift lever
Mounting angle adjustment
Adjust the mounting angle to less than 30°.
Supplied with XA-C30
* 3
Fuse (10 A)
AUX IN
AUDIO OUT
(FRONT)
AUDIO OUT
(REAR)
L
R
AUX IN
2
*
4
Black
Blue/white striped
White
Blue
White/black striped
Light blue
Grey
Grey/black striped
Orange/white striped
Green
Red
Green/black striped
Purple
Yellow
Purple/black striped
WX-7700MDX
to dashboard/centre console
1 2
or
max. size 5 × 8 mm
Bracket
Mounting the unit in a Japanese
car (4)
You may not be able to install this unit in some
makes of Japanese cars. In such a case, consult
your Sony dealer.
When mounting this unit to the preinstalled
brackets of your car, use the supplied screws 1
or 2 in the appropriate screw holes, according
to your vehicle: T for TOYOTA, M for
MITSUBISHI, and N for NISSAN.
Notes
• Use the screws 1 or 2 depending on the make of
car. When this unit is attached to a MITSUBISHI car,
use the supplied screws 2.
• To prevent malfunction, be sure to install using
brackets and the supplied screws 1 or 2.
• Do not apply excessive force to the buttons of the
unit.
• Do not push on the display window.
• Before mounting, make sure there is nothing on
the top of the unit.
Source selector
XA-C30
Supplied with the CD/MD changer
BUS AUDIO IN
L
R
REAR FRONT BUS AUDIO
AUDIO OUT IN
1
*
RCA pin cord
AMP REM
Max. supply current 0.3 A
ANT REM
Max. supply current 0.1 A
ATT
ILLUMINATION
B
NISSAN
Bracket
1 or 2
max. size 5 × 8 mm
3
Existing parts supplied with your car
Warning when installing in a car
without ACC (accessory)
position on the ignition key
switch
Be sure to press (OFF) on the unit for two
seconds to turn off the clock display after
turning off the engine.
When you press (OFF) only momentarily, the
clock display does not turn off and this causes
battery wear.
T N
M M
T
N
T
T
N
T N
N
M
WX-7700MDX
1
* not supplied
* 2 Connect the Bus cable to its
terminal with the unit's
the Bus cable's v mark aligned.
* 3 supplied with the auxiliary
equipment
from car aerial
* 4 Auxiliary optional equipment such
as portable DVD player (not
supplied)
2
3
4
5
6
7
WX-7700MDX
to dashboard/centre console
Bracket
Reset button
When the installation and connections are
completed, be sure to press the reset button with
a ballpoint pen, etc.
ANGLE
ATT
Reset button
Note
When you connect the power supply cord to the
unit or reset the unit, wait for about 10 seconds
before you insert a disc. If you insert a disc within
these 10 seconds, the unit will not be reset, and you
will have to press the reset button again.
V mark and
1 2
or
max. size 5 × 8 mm
OPEN/
CLOSE
VOL
MODE
SOURCE
DISC AMS OFF
9