Commands; A.2 Commands - Black Box AVSC-0802H User Manual

Appendix: RS-232 Command Set

A.2 Commands

IDX Function
1 Switch input for output
2 Get which input map-
ping to the indicate out-
put
3 Get which output map-
ping to all input
4 Set CEC POWER ON/
OFF
5 Get CEC POWER ON/
OFF Status
6 Set CEC POWER Delay
Time
(This command is valid
when there is no active
signal input)
7 Get CEC POWER Delay
Time
8 Set Audio Extraction
on/off
9 Get Audio
Extraction
status
10 Get Phantom Power
status
11
Adjust Volume Gain
Page 52
Command Response
SET SW in out[CR/ SW in out[CR/LF]
LF]
GET MP out[CR/LF] MP in out[CR/LF]
GET MP all[CR/LF] MP in out[CR/LF]
MP in out[CR/LF]
SET CECPWR_ CECPWR_ONOFF
ONOFF out prm[CR/ out prm[CR/LF
LF]
GET CECPWR_ CECPWR_ONOFF
ONOFF out [CR/LF] out prm[CR/LF]
SET CECPWR_ CECPWR_DELAY
DELAY out prm[CR/ out prm[CR/LF
LF]
GET CECPWR_ GECPWR_DELAY
DELAY out [CR/LF] out prm[CR/LF]
SET AUDIOEXTRACT AUDIOEXTRACT
prm[CR/LF] prm[CR/LF]
GET AUDIOEXTRACT
AUDIOEXTRACT prm[CR/LF]
[CR/LF]
GET MICPWR[CR/ MICPWR
LF] prm[CR/LF]
VOLGAIN_DATA
SET VOLGAIN_
DATA aout aout prm[CR/LF]
prm[CR/LF]
877-877-2269 | BlackBox.com
Parameters Desription
in = {hdmi1,hdmi2,hdmi3,dp,vg
a1,vga2,hdbt1,hdbt2};
out = {out1,out2};
in= {hdmi1,hdmi2,hdmi3,dp,vg
a1,vga2,hdbt1,hdbt2};
out = {out1,out2};
in = {hdmi1,hdmi2,hdmi3,dp,vg
a1,vga2,hdbt1,hdbt2};
out = {out1,out2};
all = {all};
prm = {on,off}
out = {out1,out2};
prm = {on,off}
out = {out1,out2};
out = {out1,out2};
prm = {0,1,2,3...,off}// according
to the actual time counter, 0
means 0 means, 1 means 1 min-
ute , 2 means 2 minutes and so
on, it is 2 minutes by default, the
Max wait time is 30 minutes;
off means when no active signal,
the unit will not auto power off.
out = {out1,out2};
prm = {0, 1,2,3...,off}// accord-
ing to the actual time counter,1
means 1 minute ,2 means 2 min-
utes and so on, it is 2 minutes by
default, the Max wait time is 30
minutes;
off means when no active signal,
the unit will not auto power off.
prm = {on,off}
The Audio Extraction is on by
default.
prm = {on,off}
The Audio Extraction is on
by default.
prm = {on,off}
aout = {audioout};
prm = {0~100}
Example
Command: SET SW hdmi1 out1[CR/LF]
Response: SW hdmi1 out1[CR/LF]
Command: GET MP out1[CR/LF]
Response: MP hdmi1 out1[CR/LF]
Command: GET MP all [CR/LF]
Response: MP hdmi1 out1[CR/LF]
MP hdmi2 out2[CR/LF]
Command: SET CECPWR_ONOFF out1
on[CR/LF]Response: CECPWR_ONOFF
out1 on[CR/LF]
Command: GET CECPWR_ONOFF
out1[CR/LF]Response: CECPWR_ONOFF
out1 on[CR/LF]
Command: SET CECPWR_DELAY out1
3[CR/LF]Response: CECPWR_DELAY out1
3[CR/LF]
Command: GET CECPWR_DELAY out1
[CR/LF]Response: GECPWR_DELAY out1
3[CR/LF]
Command: SET AUDIOEXTRACT on[CR/
LF] Response: AUDIOEXTRACT on[CR/LF]
Command: GET
AUDIOEXTRACT[CR/LF] Response:
AUDIOEXTRACT on[CR/LF]
Command: GET MICPWR[CR/LF]
Response: MICPWR on [CR/LF]
Command: SET VOLGAIN_DATA
audioout 50[CR/LF]
Response: VOLGAIN_DATA audio-
out 50[CR/LF]