Specifications; Frequency Range And Transmitter Output Power - Shure ULX-D User Manual

Specifications

ULXD Specifications
Working Range
100 m (330 ft)
Note: Actual range depends on RF signal absorption, reflection and interference.
Audio Frequency Response
ULXD1
ULXD2
Audio Dynamic Range
System Gain @ +10
>120 dB, A-weighted, typical
System Audio Polarity
Positive pressure on microphone diaphragm produces positive voltage on pin 2 (with respect to pin
3 of XLR output) and the tip of the 6.35 mm (1/4-inch) output.
Operating Temperature Range
-18°C (0°F) to 50°C (122°F)
Note: Battery characteristics may limit this range.
Housing
ULXD4 ULXD1
steel Cast aluminum
ULXD4Power Requirements
15 V DC @ 0.6 A, supplied by external power supply (tip positive)
Battery Type
Shure SB900 Rechargeable Li-Ion or LR6 AA batteries 1.5 V
ULXD Battery Life
SB900A
ULXD
1/10 mW
470 to 810 >11 hours
902 to 928 10 hours
174 to 216 >9 hours
1240 to 1800 >8:30 hours
The values in this table are typical of fresh, high quality batteries. Battery runtime var-
ies depending on the manufacturer and age of the battery.
Certifications
ULXD1, ULXD2, ULXD4
This product meets the Essential Requirements of all relevant European directives and
is eligible for CE marking.
ULXD1, ULXD2
Certified under FCC Part 74.
Certified by IC in Canada under RSS-102 and RSS-210.
IC: 616A-ULXD1 G50, 616A-ULXD1 H50, 616A-ULXD1 J50, 616A-ULXD1 L50;
616A-ULXD2 G50, 616A-ULXD2 H50, 616A-ULXD2 J50, 616A-ULXD2 L50.
FCC: DD4ULXD1G50, DD4ULXD1H50, DD4ULXD1J50, DD4ULXD1L50;
DD4ULXD2G50, DD4ULXD2H50, DD4ULXD2J50, DD4ULXD2L50.
IC: 616A-ULXD1X52, 616A-ULXD2X52
FCC: DD4ULXD1X52, DD4ULXD2X52
IC: 616A-ULXD1V50, 616A-ULXD2V50
FCC: DD4ULXD1V50, DD4ULXD2V50
Note: For transmitters operating in the V50 and V51 bands: nominal free space an-
tenna gain at middle of the band is typically -6 dBi, and rolls off at the band edges an
additional -4 dB.
20 – 20 kHz (±1 dB)
Note: Dependent on microphone type
ULXD2
Machined aluminum
alkaline
20 mW 1/10 mW 20 mW
>7 hours 11 hours 5:30 hours
>7 hours >9 hours 6 hours
7 hours 8 hours >5 hours
>6:30 hours >6 hours >4:30 hours
Frequency Range and Transmitter Output
Power
Frequency Range
Band
( MHz)
G50 470 to 534
G51 470 to 534
G52 479 to 534
G62 510 to 530
H50 534 to 598
H51 534 to 598
H52 534 to 565
J50 572 to 636
J51 572 to 636
K51 606 to 670
L50 632 to 696
L51 632 to 696
L53 632 to 714
P51 710 to 782
R51 800 to 810
JB (Tx only) 806 to 810
AB (Rx and Tx) 770 to 810
Q51 794 to 806
V50 174 to 216
V51 174 to 216
X50 925 to 932
X51 925 to 937.5
X52 902 to 928
902 to 907.500, 915
X53
to 928
X54 915 to 928
Z16 1240 to 1260
Z17 1492 to 1525
Z18 1785 to 1805
Z19 1785 to 1800
Z20 1790 to 1805
* Power delivered to the antenna port
Note: Frequency bands might not be available for sale or authorized for use in all
countries or regions.
For the band Z17 (1492-1525 MHz), it must be used indoors only.
For the Band Z19 (1785-1800MHz) used in Australia, per Radio Communications Low
Interference Potential Devices Class License 2015; item 30 note C: the system must
be operated within the range of 1790-1800MHz when used outdoors.
ULXD4
Approved under the Declaration of Conformity (DoC) provision of FCC Part 15.
Conforms to electrical safety requirements based on IEC 60065.
The CE Declaration of Conformity can be obtained from: www.shure.com/europe/
compliance
Authorized European representative:
Shure Europe GmbH
Headquarters Europe, Middle East & Africa
Department: EMEA Approval
Jakob-Dieffenbacher-Str. 12
75031 Eppingen, Germany
Phone: 49-7262-92 49 0
Fax: 49-7262-92 49 11 4
Email: info@shure.de
Power ( mW RMS)*
(Lo/Nm/Hi)
1/10/20
1/10/20
1/10
1/10/20
1/10/20
1/10/20
1/10
1/10/20
1/10/20
1/10
1/10/20
1/10/20
1/10/20
1/10/20
1/10/20
1/10
'A' Band (770-805): 1/10/20
'B' Band (806-809): 1/10
1/10/20
1/10/20
1/10/20
1/10
10
0.25/10/20
0.25/10/20
0.25/10/20
1/10/20
1/10/20
1/10/20
1/10/20
1/10/20
9