Advertisement
Operation Guide 5510
3. When the setting you want to change is flashing, use D and B to change it as
described below.
Screen:
To do this:
Reset the seconds to
Toggle between Daylight Saving Time
(
) and Standard Time (
Change the hour or minute
Change the year, month, or day
E-10
Daylight Saving Time (DST) Setting
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
To toggle the Timekeeping Mode digital time between DST and Standard Time
1. In the Timekeeping Mode, hold down A until the
DST indicator
seconds start to flash, which indicates the setting
screen.
2. Press C once and the DST setting screen appears.
3. Press D to toggle between Daylight Saving Time (
displayed) and Standard Time (
4. Press A to exit the setting screen.
•
The DST indicator appears on the Timekeeping,
On/Off status
Alarm, and Hand Setting Mode screens to indicate
that Daylight Saving Time is turned on.
E-12
•
High-speed hand movement will stop automatically after the time advances 12
hours or if an alarm (daily alarm, Hourly Time Signal, or countdown beeper) starts
to sound.
4. Press A to exit the setting screen.
•
The minute hand will be adjusted slightly to match the seconds when you exit the
setting screen.
To return to the Timekeeping Mode, press C.
•
E-14
•
The stopwatch measurement operation continues even if you exit the Stopwatch
Mode.
•
For information about how stopwatch times are stored in memory, see "Memory
Management" (page E-22).
Viewing the Stopwatch Digital Displays
The information that appears in the watch's upper and lower digital displays depends
on whether you are measuring lap times or split times.
Lap Time Measurement
Upper Display: Lap time
Lower Display: Elapsed time
Split Time Measurement
Upper Display: Lap time
Lower Display: Elapsed time (Split time appears here for eight seconds as it is stored
in memory.)
E-16
Seconds
Minutes
1/100 second
More than one hour
Seconds
Minutes
1/100 second
More than 10 hours
Hours
To measure elapsed time
Note
•
You can perform the following steps starting from either the lap time screen or the
split time screen.
1. Press D to start the stopwatch.
2. Press D again to stop the stopwatch.
You can resume the measurement operation by pressing D.
•
3. Press A to clear the stopwatch to all zeros.
E-18
Do this:
Press D.
Press D.
)
Use D (+) and B (–).
Use D (+) and B (–).
displayed).
Minutes
Hours
Seconds
Minutes
Hours
Seconds
4. Press A to exit the setting screen.
•
The day of the week is displayed automatically in accordance with the date
(year, month, and day) settings.
•
See "Daylight Saving Time (DST) Setting" below for details about the DST setting.
To toggle between 12-hour and 24-hour timekeeping
In the Timekeeping Mode, press D to toggle between 12-hour timekeeping and
24-hour timekeeping.
•
With the 12-hour format, the P (PM) indicator appears to the left of the hour digits
for times in the range of noon to 11:59 p.m. and the A (AM) indicator appears to the
left of the hour digits for times in the range of midnight to 11:59 a.m.
•
With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
any indicator.
•
The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all other modes.
•
The A and P indicators are not displayed with the Timekeeping Mode time on the
Countdown Timer Mode and Dual Time Mode screens.
Setting the Analog Time
Perform the procedure below when the time indicated by the analog hands does not
match the time of the digital display.
To adjust the analog time
1. In the Timekeeping Mode, press C six times to enter
the Hand Setting Mode (page E-6).
2. Hold down A until the current digital time starts to
flash, which indicates the setting screen.
3. Use D to adjust the analog setting.
Press D once to advance the hands 20 seconds.
•
Hold down D to advance the hands at high speed.
•
To lock high speed hands movement, hold down D to start it and then press B
•
to lock. The hands will continue to advance for one 12-hour cycle or until you
press any button to stop them.
Stopwatch
The stopwatch lets you measure elapsed time, lap times,
Remaining
and split times. Lap times and split times can be stored in
free records
memory.
•
The display range of the stopwatch is 99 hours,
59 minutes, 59 seconds.
•
All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C
(page E-6).
Note
Hours
•
"Lap time" is the time spent to cover a specific segment
1/100
second
of a race, such as one lap around a track. "Split time" is
Minutes
the time spent from the beginning of a race up to a
certain point.
Seconds
•
The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
•
See "To measure elapsed time with lap times" (page E-19) and "To measure elapsed
time with split times" (page E-20) for more information about each type of measurement.
•
You can perform elapsed time measurement starting from either the lap time screen
or the split time screen (page E-19 and E-20). Whenever you enter the Stopwatch Mode,
the screen (lap time or split time) that was displayed when you last exited the mode
will appear first.
•
During a stopwatch elapsed time operation, the upper display initially shows
minutes, seconds, and a 1/100-second value. This changes to hours, minutes, and
seconds when the time in the upper display exceeds 60 minutes.
•
The lower display initially shows hours, minutes, seconds, and a 1/100-second
value. This changes to hours, minutes, and seconds when the time in the lower
display exceeds 10 hours.
To measure elapsed time with lap times
1. When the stopwatch display shows all zeros, press
A to display the lap time screen (indicated by
2. Press D to start an elapsed time measurement.
•
At the time, both the upper and lower displays will
show identical times.
3. Press A to record the time of the first lap.
Lap time
•
This freezes the current lap time in the upper part of
the digital display for about eight seconds, while
measurement of total elapsed time and the next lap
time continue internally. The lap number of the
displayed time appears in the lower digital display.
•
After eight seconds, the ongoing elapsed time
measurement re-appears in the lower digital display.
4. Repeat step 3 to record more lap times.
Elapsed time
5. Press D to stop the stopwatch.
E-11
E-13
E-15
E-17
/LAP).
E-19
Hide quick links:
Advertisement
