Summary of Contents for YUNEEC CGOET
- Page 1 USER MANUAL V1.0 Any information above might be changed due to the software update. For the latest documents, please check the official website.
- Page 2 TABLE OF CONTENTS...
-
Page 3: Specifications
H. It combines an infrared camera and an RGB camera into a single unit able to capture thermal spectrum and visible light images or video at the same time. The CGOET was developed for customers who require infrared imaging for a wide array of professional, commercial and public service applications. The self-stabi- lizing gimbal makes it possible to capture ultra-stable still images and fluid video under the most challenging conditions. -
Page 4: General Warnings
GENERAL WARNINGS IMPORTANT NOTE: All safety precautions and warnings, instructions, warranties and other collateral information are subject to change at the sole discretion of Yuneec. For the most up-to-date information please visit the corresponding product page at www.Yuneec.com or contact the nearest Yuneec office or authorized distributor. - Page 5 Do not expose the CGOET gimbal camera to water, including rain and mois- ture. Do not expose the lens of the CGOET gimbal camera to excessive light sources.
- Page 6 Do not operate the Gimbal in the rain! Do not expose the Gimbal to fire sources! Do not touch or move the Gimbal until the initialization process has been completed. In need of repair, send the CGOET gimbal camera to an authorized service center.
-
Page 7: Sd Card Installation
PREPARATIONS SD CARD INSTALLATION NOTICE: Before using the CGOET, a SD card should be inserted into the camera. (A SD card is included in the package.) Step 1) Slide the memory card into the card slot according to the direction of the arrow. -
Page 8: Single Mode
SINGLE MODE CREATE A NEW MODEL Step 1) First, switch on Typhoon H and then power on the ST16 Ground Station. Step 2) Tap the “Model Select” button, and if required press “OK” to accept any pop up warnings/alerts. Welcome,Pilot 1:39 AM 0 VOLTS 7.23G... - Page 9 Step 1) Press “System Settings” on the screen, and if required press “OK” to accept any pop up warnings/alerts. Step 2) Tap the “Camera Select” button, choose the gimbal camera type CGOET, and press “Select” to confirm. If required press “OK” to bypass any pop up warn- ings/alerts.
- Page 10 Welcome,Pilot 1:39 AM 7% Aircraft Model Camera Not connected Not connected SR24S_63452v1.06 CGOET_42000B CGO3P_C2096F CGO3P_B2002E CGO3P_C202FB CGO3P_C20996 CGO3P_B20048 CGO3+_320739 About Controller Step 6) Input the password "1234567890" as requested, and tap "OK". Welcome,Pilot 1:39 AM 7% User Login CGOET_42000B Password: Show password Cancel 1:39 AM 7%...
- Page 11 ] in the lower right column of the ST16, and then switch from single mode to team mode. (At this time, the copter cannot be controlled by the ST16 anymore, but the CGOET gimbal camera can still be con- trolled by the ST16.)
- Page 12 CGOET from the factory, and controls both the copter and the CGOET Gimbal Camera. NOTICE: After switching from single mode to team mode (Wizard and ST16) on the ST16 , the Wizard must be bound to the copter and the ST16 Ground Station must be bound to the camera.The Wizard controls the copter and the ST16...
- Page 13 ST16 is successfully bound to Typhoon H. NOTICE: The default mode of the system is single mode. The original ST16 Ground Station comes bound to the copter and the CGOET from the factory , and controls both the copter and the CGOET Gimbal Camera.
-
Page 14: Camera Controls
Velocity Mode. When the slider (C) is in the middle position, it means the velocity rate is 0 for the CGOET, and it will stop tilting up/down. When the slider (C) is above the middle position, the CGOET will start tilting up. - Page 15 There is a gimbal tilt mode switch on ST16---S1. When the switch is in up/middle posi- tion, the CGOET gimbal camera is in Angle Mode. Use the slider (C) on the left side of the ST16 to set the tilt position of the gimbal camera. When the S1 is in bottom posi- tion, the gimbal camera is in Velocity Mode.
- Page 16 ‘shutter’ sound from the ST16 and the green LED indicator on the front of the CGOET will blink blue once every time when taking a photo. It will take ap- proximately 1-2 seconds to capture the photo and before you can take another still photo.
-
Page 17: To Record Video
Press the button located near the lower right corner of the ST16. You'll hear an audible indication from the ST16 each time the recording starts/stops. While video is recording, the LED indicator on the front of the CGOET will flash blue and green. - Page 18 ST16 Ground Station. CAUTION: ALWAYS stop recording video before turning off the Typhoon H/C- GOET to avoid data loss. If you accidentally turn off the Typhoon H/CGOET before you stop recording, re-insert micro SD card (if removed) and turn the system on again.
- Page 19 Model: Typhoon H Welcome,Pilot 1:39 AM 0 VOLTS 43.9 C 7.23G 15.6V + 41.8 C Ready OBS. Disabled 0.0000 E 0.0000 N CALIBRATION -0.0 m G-SPD AVAILABLE 0.0 KPH TASK N/A m 41.3 C CAMERA System Settings Channel Settings Model Select 2) “Blend”...
- Page 20 3. Tap [ ] icon and choose “System” , you can have several setting options. For instance: “Photo” , “ROI” , “Palette” , “Auto Calibrate” , “Reset” , “Format Sdcard” , etc. Model: Typhoon H Welcome,Pilot 1:39 AM 0 VOLTS 43.9 C 7.23G 15.6V...
- Page 21 Model: Typhoon H Welcome,Pilot 1:39 AM 0 VOLTS 43.9 C 7.23G 15.6V Photo Ready OBS. Palette Disabled Fusinon 0.0000 E 0.0000 N Rainbow Globow CALIBRATION -0.0 m Icefire G-SPD Ironblack 0.0 KPH AVAILABLE Single/Team TASK 41.3 C N/A m Auto Calibrate CAMERA Reset Channel Settings...
-
Page 22: Led Status Indications
Blinks orange very rapidly (10 times per second) - The Aircraft is in a No-Fly Zone Blinks red and white rapidly (5 times per second) CGOET CAMERA LED STATUS INDICATIONS - Without T-card or T-card Memory Full Blinks yellow - WiFi Error... -
Page 23: Certification Information
CERTIFICATION INFORMATION FCC STATEMENT: This equipment has been tested and found to comply with the limits for Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accor- dance with the instructions, may cause harmful interference to radio communica- tions. -
Page 24: Rf Exposure Warning
—Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. CAUTION: Any changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate this equip- ment. -
Page 25: Ncc Warning Statement
Tel: +86 400 8207 506 COLLECTION AND PROCESSING OF DATA Yuneec may collect navigation information such as GPS data to help improve our products. We may also collect Depth Map information and Infrared Image infor- mation from your drone delivered to our service center for repair and mainte- nance service or any other service. - Page 26 (i) protect ourselves or others from fraudulent, unlawful, or abusive activities; (ii) take precautions against poten- tial liability; (iii) protect the security of the Yuneec Apps embedded into or down- loaded onto your drone or any associated equipment and services; (iv) protect the legal rights of ourselves or any others.