This cable - just like all remaining connection/feeder cables between Controller and CCD - should not be laid parallel to power cables in order to prevent in- ductive or capacitive linking of high-energy transients and thus possible over voltage damage in the CONTROLLER.
0.5 mm above the table. Thus touching the table with the tools is not possible. Bungard Elektronik GmbH & Co. KG, Rilkestraße 1, 51570 Windeck – Germany Tel.: +49 (0) 2292/9 28 28 - 0, Fax: +49 (0) 2292/9 28 28 - 29, E-mail: support@bungard.de...
Page 15
ATC: connect machine to compressed air supply (6-8 bar, oil free; not included in deliver) Bungard Elektronik GmbH & Co. KG, Rilkestraße 1, 51570 Windeck – Germany Tel.: +49 (0) 2292/9 28 28 - 0, Fax: +49 (0) 2292/9 28 28 - 29, E-mail: support@bungard.de...
Page 16
Now please insert the spindle into the spindle holder and connect the connection cable. Bungard Elektronik GmbH & Co. KG, Rilkestraße 1, 51570 Windeck – Germany Tel.: +49 (0) 2292/9 28 28 - 0, Fax: +49 (0) 2292/9 28 28 - 29, E-mail: support@bungard.de...
Page 17
A driver installation is not required. If problems arise in this regard, please contact support@bungard.de. Bungard Elektronik GmbH & Co. KG, Rilkestraße 1, 51570 Windeck – Germany Tel.: +49 (0) 2292/9 28 28 - 0, Fax: +49 (0) 2292/9 28 28 - 29, E-mail: support@bungard.de...
Page 18
You can also check the function of spindle as well as camera, dispenser or laser, if there. Bungard Elektronik GmbH & Co. KG, Rilkestraße 1, 51570 Windeck – Germany Tel.: +49 (0) 2292/9 28 28 - 0, Fax: +49 (0) 2292/9 28 28 - 29, E-mail: support@bungard.de...
Show material ▪ Set the intensity of the line ▪ grid Bungard Elektronik GmbH & Co. KG, Rilkestraße 1, 51570 Windeck – Germany Tel.: +49 (0) 2292/9 28 28 - 0, Fax: +49 (0) 2292/9 28 28 - 29, E-mail: support@bungard.de...
Page 27
IsoCam. Height calibration is also possible with the help of standardized templates. Bungard Elektronik GmbH & Co. KG, Rilkestraße 1, 51570 Windeck – Germany Tel.: +49 (0) 2292/9 28 28 - 0, Fax: +49 (0) 2292/9 28 28 - 29, E-mail: support@bungard.de...
Page 28
For that reason all builders and makers have now the opportunity to develop their ideas for the Bungard CCD. We offer the interface so you can remote control the CCD with your own application. This enables you to mount tools or measuring devices onto the CCD, these devices will then transfer data to your application and your application again interacts according to the data input with the CCD.
Old parts shall become our property. Disclaimer of warranty Bungard GmbH & Co.KG reserves the right to change or enhance its machines or machine specifications ac - cording to its judgement, if necessary. Bungard cannot be held responsible to implement aforesaid changes into machines sold already.