Table of Contents
Advertisement
Quick Links
INSTALLATION
MANUAL
Remote Control Auto Starter
With Keyless Entry and Panic
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
[1] This device may not cause harmful interference; and
[2] This device must accept any interference received,
including interference that may cause undesired operation.
Note: The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this equipment.
Such modifications could void the user's authority to operate the equipment.
Model PL70
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Magnadyne PL70
Summary of Contents for Magnadyne PL70
- Page 1 [2] This device must accept any interference received, including interference that may cause undesired operation. Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user's authority to operate the equipment. Model PL70...
-
Page 2: Installer Warnings
Installer Warnings This remote starter with keyless entry system is designed to be installed on fuel injected vehicles with an automatic transmission ONLY. • Never install this remote starter on a manual transmission vehicle. • Some automatic transmission vehicles [mainly older GM vehicles with a purple starter wire] have a mechanical-type park safety switch instead of an electrical safety switch. - Page 3 Installation (continued) Yellow Wire with White Stripe: [Ignition 2 Output] • Provides [+] 12 volts while cranking and while running on remote control. • Some vehicles have [2] ignition wires that must be powered. • Connect to the vehicle's 2nd ignition wire that goes hot in the start and remains hot in the run position. If this wire is not used, cap the end of the wire.
- Page 4 Installation (continued) Cavity #8 Vacant: [Rear Hatch/Trunk Pop Output] This vacant cavity outputs a [-] signal to pop the rear hatch when the remote transmitter “UNLOCK” button is depressed for 3 seconds or more. • The #8 cavity sends out a [-] signal to activate a relay coil. [300mA maximum] For vehicles that use a [-] pulse to engage an existing factory trunk pop relay: •...
-
Page 5: Optional Accessory Connections
Optional Accessory Connections 3 Wire Positive Trigger Door Lock System 3 Pin Black Plug Black Wire: Connect to Lock Orange Wire: No Connection Lock Control Switch Red Wire: Connect to Unlock (+) Lock Out +12 Volts Input To Door Lock Control Relays (+) Unlock Out Note: Prewired Door Lock Interconnect T-Harness are Available for Most Vehicles... -
Page 6: Black Wire
Optional Accessory Connections Newly Installed Power Door Lock Motors Red Wire: Lock Orange Wire: No Connection Black Wire: Unlock Violet Wire To +12 Volts (Battery +) 3 Pin Black Plug White Wire Brown Wire To Ground ALA-DL1 Relay Pack Green Wire: Lock To Newly Installed Power Blue Wire: Unlock... - Page 7 Optional Accessory Connections (continued) Unlock Driver’s Door First for 3-Wire Negative Door Lock Systems Red Wire Lock All Doors Orange Wire Unlock Remaining Doors Black Wire Unlock Drivers Door Must Add +12V ALA984H Relay Passenger Drivers Door Switch Door Switch Lock Unlock To +12V...
- Page 8 Optional Accessory Connections (continued) Power Trunk Activation Using Optional 30 Amp Relay Insert White Wire with Black Stripe into the Eighth Socket Output to Power Trunk Switch White Wire with Black Stripe To Constant +12 Volts (SPST ALA984H Input to Relay (+ or -) Relay Not Supplied) 2 Pin Orange Port [Pass-Key, Pass Lock, Transponder and Anti-Starter Grind] The orange port on the control module can be used to interface with Pass-Key, Pass-Lock and Transponder vehicles or for anti-...
- Page 9 Optional Accessory Connections (continued) Transponder Interfacing • You will need a Transponder Key that’s already programmed to the vehicle. • You will also need a Transponder Interface Module. Our RS-TIM Module plugs directly into the Remote Starter Module. • Detailed instructions are included with the RS-TIM Module. Pass-Key Interfacing Using ALA-RP2 If you are not using our module you can still follow these instructions by relay terminal # and using a normal If you are not using our module you can still follow these instructions by relay terminal # and...
- Page 10 Optional Accessory Connections (continued) Pass-Lock Interface Pass Lock Wire Colors Type 1 Type 2 Type 3 Ignition White Black/White White/Red Switch Black Black Orange/Black Pass Lock Decoder Yellow Black Yellow Green Wire (87A) ALA-RP1 Purple Wire (30) Relay Pack Orange Wire (87) 2-Pin Orange or Red Connector Correct Resistor The Pass-Lock system is similar to the Pass-Key system except the resistor is inside the steering column instead of...
-
Page 11: Tran Sm It Ter Code Learning
Tran sm it ter Code Learning To Enter Code Learning Mode: [The Module Learns Up To 4 Transmitter Codes] 1. Turn on the ignition key. 2. Depress the program switch [3] times within 30 seconds. after turning ignition key. 3. The horn will emit [1] long chirp to indicate you are now in code learning mode. 4. - Page 12 Last Door Automatic Arming Starter Interrupt Programming The alarm module can be programmed to automatically arm the starter interrupt port 30 seconds after you exit the vehicle. In addition, the doors can also be programmed to lock or not lock upon automatic passive arming of the starter interrupt port.
- Page 13 Remote Starter Feature Programming To Enter Remote Starter Feature Programming: 1. Turn on the ignition key. 2. Depress the program switch [10] times within 30 seconds. after turning on ignition. 3. The parking lights will flash [10] times. The horn will chirp [10] times. 4.
- Page 14 Miscellaneous Feature Programming To Enter Miscellaneous Feature Programming: 1. Turn on the ignition key. 2. Depress program switch [15] times within 30 seconds after turning on the ignition. 3. The parking lights will flash [15] times. The horn will chirp [15] times. 4.
-
Page 15: Troubleshooting
Trouble Shooting 1. Remote Starter Module Will Not Activate: • The hood switch may be pointed in the wrong direction. Disconnect and re-try. • Probe the pink brake wire to verify the wire is not until the brake is depressed. •... -
Page 16: Programming Switch
(See Auto Door Locking) Gray Wire (-) Ground Upon Remote Start Signal Vacant Trunk-Pop Output (-) (ALA-RPT) Red/White Wire Parking Lights (+) or (-) Output Pink Wire Brake Switch Turn Off © 2000 Copyright Magnadyne Corp. 3-10-00 Rev. B PL70IM...
Need help?
Do you have a question about the PL70 and is the answer not in the manual?
Questions and answers