Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Harken 20 STA
Summary of Contents for Harken 20 STA
- Page 1 Installation and Maintenance Manual MRW-03 Radial Winch 20 ST...
-
Page 2: Table Of Contents
Assembly Harken limited worldwide warranty ® Ordering spare parts Exploded view Parts List Radial Winch 20 STA Radial Winch 20 STC Radial Winch 20 STCW Radial Winch 20 STBBB Radial Winch 20 STCCC 20 ST Installation and Maintenance Manual Radial Winch... -
Page 3: Introduction
® In case of doubt the Harken Tech Service is at your disposal at techservice@harken.it ® This Manual is available only in English. If you do not fully understand the English language, do not carry out the operations described in this Manual. -
Page 4: Installation
It is the installer's responsibility to carry out all structural tests needed to ensure that the deck can bear the load. Harken does not supply the screws needed to install the winch since these may vary depending ®... -
Page 5: Procedure 1
The winch can be installed following one of the two procedures below (Procedure1 or Procedure 2): Procedure 1 To install the winch you must remove the drum and use bolts as described ahead. Tools needed One medium flat-bladed screwdriver To identify the various parts, refer to the exploded view at the end of this Manual. Torque to apply when assembling 2. -
Page 6: Procedure 2
5. Lift off the drum n°13 Winch STA, STC and STCW versions: Install the winch on the deck in the position you have chosen, keeping in mind the limits described on page 4 and using socket head (SH) bolts. Winch STBBB and STCCC versions: Install the winch on the deck in the position you have chosen, keeping in mind the limits described on page 4 and using socket head (SH) bolts or hexagonal headed bolts (HH). - Page 7 3. Position the 5 M6 hexagonal headed bolts in their holes 4. Reposition the skirt n°2 in its housing 5. Press down the skirt to position it correctly NOTICE Make sure the skirt is correctly clipped on to the base of the winch. Install the winch on the deck in the position you have chosen, keeping in mind the limits described on page 4 and using hexagonal headed bolts (HH).
-
Page 8: Installation Procedure
60° Ø110 B. Remove the winch and drill the five 6.2 mm diameter holes. C. Bolt the base of the winch to the deck using five M6 bolts (not supplied by Harken ) as ® described at Procedure 1 or Procedure 2, correctly chosen for the thickness and type of the boat deck. -
Page 9: Positioning The Self-Tailing Arm
Installation and maintenance of winches must be carried out exclusively by specialized personnel. In the case of doubt contact Harken Tech Service at techservice@harken.it ®... - Page 10 Carry out Procedure 1 as shown in the paragraph on winch installation and then do the following: 6. Completely unscrew the three screws n°18 7 . Remove the self-tailing arm support n°12 and slide out the bushing 8. Slide out the central shaft n°7 9.
- Page 11 If it is necessary to replace any jaws of the winch, proceed as follows: I. Unscrew the 3 screws n°16 II. Remove the jaws n°15 ( 4Nm/35 in-lb) If it is necessary to remove any pawls in the central shaft, proceed as follows: Unscrew the screw n°10 and remove the washer n°9 ( 4Nm/35 in-lb) Once the winch is completely disassembled, clean the parts: use a basin of diesel oil to soak...
-
Page 12: Exploded View With Maintenance Products
Exploded view with maintenance products Anti-seize ® Harken Grease Harken ® Pawl Oil Threadlocker 1. Apply Harken grease on assy socket screw - 2. Apply Harken grease on drum gear ® ® 20 ST Installation and Maintenance Manual Radial Winch... -
Page 13: Assembly
Hold the spring closed and slide the pawl into its housing. Once in position, check that the pawls can be easily opened and closed with a finger. In case of doubt concerning the assembly procedure contact Harken Tech Service: ® techservice@harken.it... -
Page 14: Harken ® Limited Worldwide Warranty
Harken® limited worldwide warranty - Ordering spare parts Harken limited worldwide warranty ® Refer to the Harken Limited Worldwide Warranty in the Harken Catalogue and on the website ® ® www.harken.com Ordering spare parts Spare parts can be requested from Harken ®... -
Page 15: Exploded View
Exploded view Exploded view Radial Winch 20 STA, STC, STCW 20 ST Installation and Maintenance Manual Radial Winch... - Page 16 Radial Winch 20 STA, STC, STCW 20 ST Installation and Maintenance Manual Radial Winch...
- Page 17 Radial Winch 20 STBBB, STCCC 20 ST Installation and Maintenance Manual Radial Winch...
- Page 18 Radial Winch 20 STBBB, STCCC 20 ST Installation and Maintenance Manual Radial Winch...
-
Page 19: Parts List
Screw M6x50 UNI6107 M6007103 Cover 1 Speed W20 S4135800A5 Assy Socket W20-80 A94136400 Socket Handle W20/80 S415130085 Washer Ø7.7xØ25x5.8 M0614303 Screw M8x20 UNI 6109 *Available with service kit; see website www.harken.com **Winch product sticker 20 ST Installation and Maintenance Manual Radial Winch... -
Page 20: Radial Winch 20 Stc
Screw M6x50 UNI6107 M6007103 Cover 1 Speed W20 S4135800A5 Assy Socket W20-80 A94136400 Socket Handle W20/80 Washer Ø7.7xØ25x5.8 S415130085 M0614303 Screw M8x20 UNI 6109 *Available with service kit; see website www.harken.com **Winch product sticker 20 ST Installation and Maintenance Manual Radial Winch... -
Page 21: Radial Winch 20 Stcw
M6007103 S4135800A5W Cover 1 Speed W20 RAL9003 Assy Socket W20-80 A94136400 Socket Handle W20/80 S415130085 Washer Ø7.7xØ25x5.8 Screw M8x20 UNI 6109 M0614303 *Available with service kit; see website www.harken.com **Winch product sticker 20 ST Installation and Maintenance Manual Radial Winch... -
Page 22: Radial Winch 20 Stbbb
COVER W20 BBB A76932000 Assy Socket W20-80 A94136400 Socket Handle W20/80 S415130085 Washer Ø7.7xØ25x5.8 M0614303 Screw M8x20 UNI 6109 Winch Product Sticker** *Available with service kit; see website www.harken.com **Winch product sticker 20 ST Installation and Maintenance Manual Radial Winch... -
Page 23: Radial Winch 20 Stccc
Cover W20 CCC A76811000 Assy Socket W20-80 A94136400 Socket Handle W20/80 S415130085 Washer Ø7.7xØ25x5.8 M0614303 Screw M8x20 UNI 6109 Winch Product Sticker** *Available with service kit; see website www.harken.com **Winch product sticker 20 ST Installation and Maintenance Manual Radial Winch...
Need help?
Do you have a question about the 20 STA and is the answer not in the manual?
Questions and answers