Snow Performance 20010 Installation Instructions Manual

Water/methanol injection systems
Hide thumbs Also See for 20010:

Advertisement

INSTALLATION
INSTRUCTIONS FOR PART
#20010 WATER/METHANOL
INJECTION SYSTEMS
© 2005, Snow Performance, Incorporated
Contents:
Parts List...................................................................................3
Introduction...............................................................................4
Installation Mechanical.............................................................4
Testing Pump and Mechanical System....................................8
Variable Controller Installation ................................................9
Testing the Controller............................................................. 10
Variable Controller Tuning ..................................................... 10
Controller Operation Example................................................ 11
Timing Adjustment ................................................................. 12
Tuning Quick Reference......................................................... 12
Maintenance............................................................................ 13
Fluid Level Switch (optional).................................................. 14
Solenoid Upgrade (optional) .................................................. 15
Install Notes ............................................................................ 16
Disclaimer ............................................................................... 17
Contact Us .............................................................................. 19
CAUTION
You must completely read though these instructions before installing and
operating this product. Failure to due so can result in damage to this
product and the vehicle.
© 2005, Snow Performance, Incorporated

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 20010 and is the answer not in the manual?

Questions and answers

Summary of Contents for Snow Performance 20010

  • Page 1: Table Of Contents

    Contact Us ................19 CAUTION You must completely read though these instructions before installing and operating this product. Failure to due so can result in damage to this product and the vehicle. © 2005, Snow Performance, Incorporated © 2005, Snow Performance, Incorporated...
  • Page 2: Parts List

    - Screw driver – Phillips #8x1½” sheet metal screws and - 5/16” open end wrench (for nozzle) washers provided. Optional: If windshield washer reservoir is utilized, mount © 2005, Snow Performance, Incorporated © 2005, Snow Performance, Incorporated...
  • Page 3 (the pump has an arrow hand tight using a 5/16” wrench. CAUTION: to over torque the indicating flow direction between nozzle will result in reduced nozzle flow. inlet and outlet ports) and cut © 2005, Snow Performance, Incorporated © 2005, Snow Performance, Incorporated...
  • Page 4: Testing Pump And Mechanical System

    - Using a 12v source, apply 12v to the pump red wire (disconnect wire at pump). Pump should activate and fluid level in tank should go down. Also check for leaks. © 2005, Snow Performance, Incorporated © 2005, Snow Performance, Incorporated...
  • Page 5: Variable Controller Installation

    • Next, adjust “Full Psi” to the engines max boost output. controller. © 2005, Snow Performance, Incorporated © 2005, Snow Performance, Incorporated...
  • Page 6: Controller Operation Example

    - If you have to increase the onset too high in the rpm range controller will linearly adjust the pump pressure as shown on the (detonation control is needed sooner), decrease pump graph. pressure, go to a smaller nozzle. © 2005, Snow Performance, Incorporated © 2005, Snow Performance, Incorporated...
  • Page 7: Maintenance

    White wire to one of the White wires of the level switch. For best performance, cooling and system life it is recommend that Snow Performance Boost Juice™, part #40008, be the - Connect other White wire of the level switch to vehicle ground.
  • Page 8: Solenoid Upgrade (Optional)

    Solenoid Upgrade (optional) Install Notes: The optional solenoid upgrade from Snow Performance, part Pump Setting ____________(psi) #40060, is required if the nozzle is to be installed after the intake throttle plate, or the fluid reservoir is mounted higher then the nozzle.
  • Page 9: Disclaimer

    Snow Performance Inc., Its agents, employees or owners shall not long as : be under any liability whether in contract or otherwise whether or not The exclusive fluid used in the kit has been Snow performance s Boost resulting from our negligence or contents of information supplied for Juice water methanol product as evidenced by sales receipts confirming any damage or loss resulting from such information.
  • Page 10: Contact Us

    The contents of this document are subject to change without prior notice. No part of or this entire document may be reproduced in any form without prior written permission of Snow Performance, Inc under the copyright except for private use.

Table of Contents