Page 1
BLAZER GT MOBILE CLEANING UNIT Operating Instructions (ENG) MODELS: BLAZER GT 1.001-121.0 Read instructions before operating the machine. 86317260 - B 07/30/09...
RETURNED TO YOUR DEALER. PROFESSIONAL CHEMICALS CORPORATION 325 SOUTH PRICE ROAD CHANDLER, ARIZONA 85224 Information in this document is subject to change without notice and does not represent a commitment on the part of Professional Chemicals Corporation. 86317260 BLAZER GT...
Each unit will require a fuel system installation kit that is following items (unless otherwise specified) and purchased separately from the unit . any optional accessories which were ordered: 86317260 BLAZER GT...
KIT INSTRUCTIONS which came with the kit. It contains replacement parts numbers needed for ordering future parts. NOTE: The manual part number is located on the lower left corner of the front cover. 86317260 BLAZER GT...
Always wear hearing protection when unit is running. Always comply with your company’s Personal Protection Equipment (PPE) plan. Always comply with local noise ordinance when operating units. 86317260 BLAZER GT...
Page 9
Use only ProChem supplied fuel installation kits. Ensure to use the kit specific for the truckmount model and van model being used. When traversing the vehicle floor with fuel lines, always use a bulkhead adapter. This will prevent leakage and ensure that the hose is not punctured by vehicle vibration abrasion.
Manufacturer recommends floor tool tip sizing not exceed a total of “.030”. Using larger jet sizes on your cleaning unit may reduce cleaning temperatures. Example: Tri-jet wand uses three 95010 jets (95° spray angle w/ 010 orifice). 01 x 3 = 030 Upholstery tool jet size: 80015 Stair tool jet size: 9502 86317260 BLAZER GT...
Ten percent (10%) of the total trailer weight, not exceeding 800 lbs, should be on the tongue. Load the unit and accessories approprately. 86317260 BLAZER GT...
However, to obtain optimum results with will be using water in which the hardness exceeds 3-1/ this unit, we recommend using the Prochem line of 2 grains, we highly recommend a suitable water chemicals. For information on using the cleaning softener be installed.
Page 15
To turn power off, rotate key in accordance with this manuals maintenance counter clockwise to stop position, engine will then table.) stop. 10. LUBRICATION CUP The lubrication cup allows lubricant spray to reach the vacuum blower. 86317260 BLAZER GT...
Page 16
DO NOT run this unit in an enclosed area. DO NOT operate this unit where the exhaust may enter any building doorway, win- dow, vent, or opening of any type 86317260 BLAZER GT...
The air is then filtered and rushes into the vacuum pump. HOT AIR TO HEAT EXCHANGER LUBRICATION VACUUM RELIEF VACUUM VALVE GAUGE VACUUM INLET VACUUM SILENCER VACUUM PUMP LEVEL SENSOR (ENGINE SHUT-OFF SWITCH) FILTER STRAINER WASTE TANK 86317260 BLAZER GT...
The cleaning solution then passes through high- pressure hoses and is distributed by the cleaning tool to a surface that is being cleaned, completing the water pumping and heating cycle of the cleaning unit 86317260 BLAZER GT...
Page 19
HOT AIR FROM VACUUM PUMP REAR HEAT EXCHANGER CORES W ATER BOX FRONT W ASTE TANK TEMPERATURE RELIEF VALVE W ATER PUMP PRESSURE GAUGE TEMPERATURE PULSE HOSE CONTROL VALVE CHEMICAL INJECTION PRESSURE REGULATOR CHECK VALVE SOLUTION SCREEN SOLUTION OUTLET 86317260 BLAZER GT...
METERING VALVE CHEMICAL PUMP OUTLET CHECK VALVE CHEMICAL JUG OUTLET SCREEN CONTROL VALVE SOLUTION OUTLET PRIME FLOW METER WATER PUMP 86317260 BLAZER GT...
Connect the hose to the water supply fau- cet. NOTE: Never use your waste pump outlet hose as a water inlet hose. Use only clean hoses for water inlet. 2. Turn the water supply faucet on. The water will fill the water box. 86317260 BLAZER GT...
We recommend that you use a 3/4" I.D. water hose as a waste pump outlet hose. DO NOT use a hose smaller than 5/8" I.D. NEVER use your automatic waste pump outlet hose as a water inlet hose. 86317260 BLAZER GT...
5. Disconnect all hoses and tools. This unit must be operated with the vehicle or 6. Drain waste tank and rinse with clean water. trailer doors open in order to ensure adequate engine ventilation. 86317260 BLAZER GT...
Repeat this procedure with all the remaining tools. After all tools and pressure hoses have been filled with anti- When disposing of used anti-freeze, observe local freeze, disconnect and store them. laws and regulations. Do not drain onto the ground or into storm drainage systems. 86317260 BLAZER GT...
When disposing of used anti-freeze, observe local anti-freeze is purged from the tools and hoses. laws and regulations. Do not drain onto the ground or into storm drainage systems. 86317260 BLAZER GT...
200 hrs Check connections and hose wear Engine 200 hrs Check spark plugs for carbon deposits and proper gap Chemical Valves 200 hrs Inspect and/or adjust packing nuts Heat Bypass Valve 200 hrs Inspect and/or adjust packing nuts 86317260 BLAZER GT...
Page 27
***Change engine crankcase oil and filter after the first 5 hours ****Perform drive belt, pulley and hub maintenance after the first 25 hours of operation, and then again at 100 hours *****If using Tuthill Pneulube synthetic lubricant, 4500 hours or every 2 years, whichever comes first 86317260 BLAZER GT...
To keep your chemical system functioning properly, follow the chemical pump and solution outlet maintenance in the Maintenance Schedule in this manual. Refer any additional questions to your dealer. 86317260 BLAZER GT...
4. Replace the air cleaner element every year. 5. Replace the in-line gas filter every 500 hrs. NOTE: If service or repair is required, contact an authorized Briggs & Stratton Service Center. You will need to provide the serial number of the engine. 86317260 BLAZER GT...
5 seconds while the unit is running and the 5. Bearings on the drive end of the blower require vacuum inlets are sealed. Do this at the end of grease lubrication every 250 hours of operation. each working day. 86317260 BLAZER GT...
16, Amoco Rykow 68, and Shell Tellus T68. 4. Check for pulley groove wear, clean belts and pul- ley grooves, check for worn belts, proper belt ten- sion, and pulley alignment after the first 25 hours and then again at 100 hours. 86317260 BLAZER GT...
However, if the Y-strainer has a frequent build- up of debris it should be inspected and cleaned more around the hinge of the float valve. Check the float often. valve for debris at least once a month. 86317260 BLAZER GT...
Adjustments” section in this manual for details. Pressure Regulator Lubricate the o-rings and bullet every 50 hours. Use o- ring lubricant Part #86265430, PRV NO. 05-008035. For the procedure, see the "General Service Adjust- ments” section in this manual for details. 86317260 BLAZER GT...
CHECK VALVE CAP Tight wrap O-RING on spring POPPET SEAT Use 5/16 Allen O-RING Wrench to remove NOTE: Improper seating of the check valve poppet, damaged spring or o-rings will cause poor operation of the chemical system. 86317260 BLAZER GT...
(cap) (while observing the pressure gauge on the control panel) until the desired pressure is obtained. Retighten the locking nut. DO NOT loosen the adjusting body (cap) all the way (counterclockwise) or remove it while the unit is running. 86317260 BLAZER GT...
Cleaning tool valve is malfunctioning. Repair or replace valve. Hose inner lining is constricted. Remove restriction or replace hose. Air leak in chemical supply line, priming Check for air leaks. Replace faulty parts. valve or metering valve. 86317260 BLAZER GT...
Page 37
Disassemble the chemical pump and ruptured. replace the damaged diaphragm. Measure the pump volume. If the pump volume is less than normal, refer to “Loss of Defective cylinder in the water pump. Pump Volume” in the Troubleshooting section in this manual. 86317260 BLAZER GT...
Page 38
Check switch for proper operation, replace will not start tank. as necessary. Consult the Briggs & Stratton Vanguard Service And Repair Instruction Manual or Internal engine problem. contact your local Briggs & Stratton autho- rized repair center. 86317260 BLAZER GT...
Page 39
* NOTE: When replacing either the pump or float switch, on Internal (in tank) Pump out, use new electrical connectors and heat shrink. Inspect connection for watertight seal. 86317260 BLAZER GT...
Need help?
Do you have a question about the BLAZER GT and is the answer not in the manual?
Questions and answers