Related Manuals for Westinghouse HT351G12
Summary of Contents for Westinghouse HT351G12
- Page 1 GAS WATER HEATER HT351G12 Note: Before operating or installing this gas water heater read this manual and follow all safety rules and operating instructions. 12 L 2,800 2xAA 1/2 - 1/2 BATTERIES GAS PRESSURE CONNECTIONS...
-
Page 2: Table Of Contents
Thank you for purchasing our large capacity automatic gas water heater. Read this Manual before installing and operating and keep for future reference. CONTENTS • Special Advice --------------------------------------------------------------------------------------------- 3 • Factures & Benefits --------------------------------------------------------------------------------------- 3 • Parts Name ------------------------------------------------------------------------------------------------ 4 •... -
Page 3: Special Advice
SPECIAL ADVICE Since the combustion of the gas will consume a large amount of air and produce Carbon Monoxide while the heater is working. However, if human inbreathe too much Carbon Monoxide, it will cause danger or even death. Therefore, the users are requested to install and use this heather strictly according to this manual to avoid Carbon Monoxide toxicosis. -
Page 4: Parts Name
PARTS NAME Flue duct Front cover Flame check window Display Water flow control Flame regulator Hot water outlet Cold water inlet Gas inlet Battery box Fig. 1 JSD20-10M JSD24-12M Fig. 2 (Unit:mm) All pictures are just for reference, please see the product for the exact appearance. -
Page 5: Installation
INSTALLATION • Before installation, contact the qualified technicians in local gas dealer or gas Exhaust exit Flue manegement department to do the installation. Any random or improper installation will affect the safety use of the machine or even damage users life. Air inlet •... -
Page 6: Installation Method
INSTALLATION METHOD Installation Drill holes in the wall according to Fig.6, put an expansion bolt into the upper hole and plastic gasket into the lower hole, mount the water heater vertically on the upper bolt without inclination and tighten the lower holes with expansion bolts. - Page 7 INSTALLATION METHOD holder stand • Hot Water Outlet duct cap roof If connect the hot water outlet directly to the shower, you can use duct holder tube or rigid pipe. When install control valve or tap to the hot water flue duct outlet, or install the shower with duct holder...
-
Page 8: Operation Method
OPERATION METHOD Preparation Before Ignition • Make sure the type of gas used complies with that stipulated in the label. • Open the ventilation holes. • Turn on the gas inlet valve. How to ignite • Turn on the water valve (make sure there is water flowing out of the shower), the green indicating light will turn on with “clicking”... -
Page 9: Cautions For Safety
OPERATION METHOD Turn the water inlet tap to control water temperature: deercasing the water flow to make the water temperature high (do it slowly, if the flame extinguishes then re-ignitc by inercasing the water flow), and inercasing the water flow to make the water temperature low. - Page 10 CAUTIONS FOR SAFETY • Turn off the main gas valve and the water inlet valve in case of watershortage. • Do not place inflammables like towel or cloth onto the waster air drain outlet or the air inlet. (Fig.13) • Do not pile inflammables, explosives or volatile materials near the heater.
- Page 11 CAUTIONS FOR SAFETY Prevent Eyes From Getting Hurt Keep eyes away from the flame indicator window at a minimum safety distance of 300mm during ignition. If the first attempt of ignition fails, wait 10-20 seconds before the next attempt. Prevent No-water Burning In The Heater After each shower, make sure that the flame is extinguished when the valve is closed.
-
Page 12: Maintenance
CAUTIONS FOR SAFETY • When the heater is supplying hot water to much point at he same time, the hot water flow would be reduced, and at times not hot will issure at all. • During shower, if the heater is operated for more than 20 minutes, the flame will automatically turns off... -
Page 13: Trouble Shooting
TROUBLE SHOOTING Symptoms Remedies Reasons Turn on main valve or Gas valve not open replace the gas Turn on the main Gas valve half open valve Several opening the water inlet gas pressure Air in the gas pipe ignition Unsuitable High Contact the repairer to Pressure...