Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Audiovox Rampage AMP-592C
Summary of Contents for Audiovox Rampage AMP-592C
- Page 1 ModelAMP-592C 200WattStereoAmplifier Released 2-1-00. Owner's Owner's Owner's Owner's Owner's Manual Manual Manual Manual Manual 128-5721 128-5721 128-5721 128-5721 128-5721 SHT. 1 OF 12 SHT. 1 OF 12 SHT. 1 OF 12 SHT. 1 OF 12 SHT. 1 OF 12...
-
Page 2: Table Of Contents
INDEX INDEX INDEX INDEX INDEX S p e c i f i c a t i o n s ............1 P r e c a u t i o n s . -
Page 3: Specifications
Channel Separation: 50 dB Signal / Noise Ratio: 90 dB (A-Weighted) Input Impedance: low-level 10K ohms high-level 100 ohms * Due to continuing improvement, Audiovox reserves the right to change features and design without notice. HELP! 1-800-645-4994 1-800-645-4994 1-800-645-4994 1-800-645-4994 1-800-645-4994... -
Page 4: Precautions
6 . Make certain that the speakers to be used with this amplifier are capable of handling the output power (wattage) of the unit. Use of speakers not rated for the output of this amplifier may cause damage to or failure of the speakers for which Audiovox will not be liable. 128-5721... -
Page 5: Installation Instructions
INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS 1 . Select a mounting area where the amplifier will have sufficient air circulation for proper cooling. I n a d e q u a t e a i r c i r c u l a t i o n w i l l c a u s e t h e t e m p e r a t u r e of the amplifier to rise and will trigger the thermal protection mode. -
Page 6: Wiring Instructions
WIRING INSTRUCTIONS WIRING INSTRUCTIONS WIRING INSTRUCTIONS WIRING INSTRUCTIONS WIRING INSTRUCTIONS The power and speaker wire connections for this amplifier are made via screw tightened terminal blocks. Loosen the screw for the connection to be made and fully insert the wire (strip 1/2" of insulation from the end) into the respective screw on the side panel (crimp-on "U"... - Page 7 WIRING INSTRUCTIONS WIRING INSTRUCTIONS WIRING INSTRUCTIONS WIRING INSTRUCTIONS WIRING INSTRUCTIONS 4. Speaker Connections 4. Speaker Connections 4. Speaker Connections 4. Speaker Connections 4. Speaker Connections Depending on the type and number of speakers used with the amplifier, wire them to the speaker terminals as per the appropriate wiring diagram.
-
Page 8: Input Wiring Diagram
INPUT WIRING DIAGRAM LOW-LEVEL LOW-LEVEL LOW-LEVEL LOW-LEVEL LOW-LEVEL STEREO STEREO STEREO STEREO STEREO RCA OUTPUTS RCA OUTPUTS RCA OUTPUTS RCA OUTPUTS RCA OUTPUTS RIGHT LEFT CHASSIS GROUND ON RADIO IMPORTANT IMPORTANT IMPORTANT IMPORTANT IMPORTANT USE EITHER HIGH-LEVEL OR USE EITHER HIGH-LEVEL OR USE EITHER HIGH-LEVEL OR USE EITHER HIGH-LEVEL OR USE EITHER HIGH-LEVEL OR... -
Page 9: Output Wiring Diagram
WARNING! l THIS AMPLIFIER IS DESIGNED FOR USE WITH 2 SPEAKERS l N E V E R COMBINE (BRIDGE) OUTPUTS FOR USE WITH 1 SPEAKER. l N E V E R GROUND NEGATIVE SPEAKER LEADS TO CHASSIS GROUND. l FAILURE TO WIRE CORRECTLY MAY CAUSE DAMAGE TO THE AMPLIFIER. LEFT LEFT LEFT... -
Page 10: Operation
OPERATION After initial set-up, the amplifier should not require any further adjustment unless there is a change in the car stereo or speaker system with which it is used. Power Indicator Lamps Power Indicator Lamps Power Indicator Lamps Power Indicator Lamps Power Indicator Lamps The Power Indicator Lamps will light to indicate that the unit is connected to the battery and that the Remote... - Page 11 minimum setting, or the output level increases too fast with a small rotation of the volume control, adjust the Level control to decrease the output from the system. Once the correct setting is found, this control should not require any further adjustment. Sub-Woofer Filter Selector Sub-Woofer Filter Selector Sub-Woofer Filter Selector...
- Page 12 AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or workmanship within 90 days from the date of original purcha se, such defect(s) will be repaired or replaced with new or reconditioned product (at the Company's option) without charge for parts and repair labor.
Need help?
Do you have a question about the Rampage AMP-592C and is the answer not in the manual?
Questions and answers