WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Registration Information FCC Information Use the attached speciﬁ ed cables with this monitor so as not to interfere with radio and television reception. The power supply cord you use must have been approved by and comply with the safety standards of U.S.A., and meet the following condition.
Windows is a registered trademark of Microsoft Corporation. NEC is a registered trademark of NEC Corporation. ErgoDesign is a registered trademark of NEC Display Solutions, Ltd. in Austria, Benelux, Denmark, France, Germany, Italy, Norway, Spain, Sweden, U.K. All other brands and product names are trademarks or registered trademarks of their respective owners.
For example, if an image was on the monitor for one hour and a residual image remains, the monitor should be turned off for one hour to erase the image. NOTE: As with all personal display devices, NEC DISPLAY SOLUTIONS recommends using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use.
CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • For optimum performance, allow 20 minutes for the display to warm up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen.
Contents For contents, please refer to the contents sheet. Quick Start To attach the Base to the LCD stand: 1. Place monitor face down on a non-abrasive surface (Figure 1). NOTE: Handle with care when monitor facing down, for avoiding damage to the front control keys. 2.
3. Place hands on each side of the monitor to tilt the LCD panel 20-degree angle and lift up to the highest position. 4. Connect all cables to the appropriate connectors (Figure C.1). 20° Tilt Headphone Highest Stand Position DisplayPort DisplayPort D-SUB HDMI...
8. Turn on the computer and the monitor by touching the power key on the front bezel (Figure E.1). 9. No Touch Auto Adjust automatically adjusts the monitor to optimal settings upon initial setup. For further adjustments, use the following OSD controls: •...
Screen Rotation Before rotating, disconnect power cord and all cables, then the screen must be raised to the highest level and tilt to avoid knocking the screen on the desk or pinching your ﬁ ngers. To raise the screen, place a hand on each side of the monitor and lift up to the highest position (Figure RL.1). To rotate screen, place a hand on each side of the monitor screen and turn it from landscape to portrait (Figure R.1).
Remove Monitor Stand for Mounting To prepare the monitor for alternate mounting purposes: 1. Disconnect all cables. 2. Place a hand on each side of the monitor and lift up to the highest position. 3. Place monitor face down on a non-abrasive surface (Figure S.1). NOTE: Handle with care when the monitor is facing down.
Mount Flexible Arm This LCD monitor is designed for use with a ﬂ exible arm. 1. Follow the instructions on how Remove Monitor Stand for Mounting to remove the stand. 2. Use the 4 screws removed from the stand or the speciﬁ ed screws to attach the arm to the monitor (Figure F.1). Caution: Use ONLY the screws (4 pcs) that were removed from the stand or the speciﬁ...
Controls OSD (On-Screen Display) Control Functions 1. Basic functions of the touch keys on the front of the monitor – SELECT INPUT/RESET OSD Menu Not displaying on screen Shortcut to Brightness. Shortcut to Volume. Displays OSD. Selects input signal. Displaying on screen Icon Select Moves leftward.
VOLUME Controls the volume of the speakers or headphones. To mute the speaker output, select Audio icon and touch “INPUT/RESET” key. BRIGHTNESS Adjusts the overall image and background screen brightness. To enter the ECO MODE, touch the “INPUT/RESET” key. ECO MODE OFF: Sets brightness variable from 0% to 100%. ECO MODE1: Sets brightness 80%.
FACTORY PRESET Selecting Factory Preset allows you to reset all OSD control settings back to the factory settings except MUTE, CARBON SAVINGS, CARBON USAGE, and SIGNAL INFORMATION. Individual settings can be reset by highlighting the control to be reset and touching the INPUT/RESET key. EXIT Selecting EXIT allows you to exit OSD menu/sub menu.
OSD TOOL LANGUAGE OSD control menus are available in nine languages. OSD TURN OFF The OSD control menu will stay on as long as it is in use. In the OSD TURN OFF sub menu, you can select how long the monitor waits after the last touch of a key to shut off the OSD control menu. The preset choices are 10 - 120 seconds by 5 seconds step.
60 Hz to 75 Hz 1400 x 1050* at 60 Hz to 75 Hz 1440 x 900* at 60 Hz NEC DISPLAY SOLUTIONS cites recommended 1920 x 1080 at 60 Hz........... resolution for optimal display performance. Active Display Area Landscape: Horiz.: 476.06 mm/18.7 inches Vert.:...
60 Hz to 75 Hz 1400 x 1050* at 60 Hz to 75 Hz 1440 x 900* at 60 Hz NEC DISPLAY SOLUTIONS cites recommended 1920 x 1080 at 60 Hz........... resolution for optimal display performance. Active Display Area Landscape: Horiz.: 527.04 mm/20.7 inches Vert.:...
Note: The manufacturing and operating carbon footprints are calculated by a unique algorithm developed exclusively by NEC for its monitors and are accurate at the time of printing. NEC reserves the right to publish updated carbon footprint values. DisplayPort: DisplayPort is designed to be the future-ready and scalable solution for high performance digital display connectivity.
Dedicated recycling sites ensure that environmentally harmful components are properly handled and securely disposed. To ensure the best recycling of our products, NEC DISPLAY SOLUTIONS offers a variety of recycling procedures and gives advice on how to handle the product in an environmentally sensitive way, once it has reached the end of its life.