Related Manuals for Omcan BS-IT-1524
Summary of Contents for Omcan BS-IT-1524
-
Page 1: Instruction Manual
Band Saws Models BS-IT-1524, 1829-M Items 10252, 17875 Instruction Manual Revised - 05/11/2017 Toll Free: 1-800-465-0234 Fax: 905-607-0234 Email: service@omcan.com www.omcan.com... -
Page 2: Table Of Contents
Table of Contents Model BS-IT-1524 / Model BS-IT-1829-M Section Page General Information --------------------------------------------------------------------------- 3 - 4 Safety and Warranty -------------------------------------------------------------------------- 4 - 9 Technical Specifications -------------------------------------------------------------------------- 9 Installation -------------------------------------------------------------------------------------- 9 - 13 Operation ------------------------------------------------------------------------------------- 13 - 14 Maintenance --------------------------------------------------------------------------------- 14 - 15... -
Page 3: General Information
If the package has suffered rough handling, bumps or damage (visible or concealed), please note it on the bill of lading before accepting the delivery and contact Omcan within 24 hours, so we may initiate a claim with the carrier. A detailed report on the extent of the damage caused to the machine must be filled out within three days, from the delivery date shown in the shipping documents. -
Page 4: Safety And Warranty
Si el paquete ha sufrido un manejo de poco cuidado, golpes o daños (visible o oculto) por favor anote en la factura antes de aceptar la entrega y contacte Omcan dentro de las 24 horas, de modo que podamos iniciar una reclamación con la compañia. - Page 5 All the above circumstances do not depend on Omcan but rather the person in charge of the machine. At the end of each shift, the machine has to be switched off and put in the emergency stop by pushing the red button.
- Page 6 Safety and Warranty PERSONAL PROTECTIVE EQUIPMENT IN CONFORMITY WITH CURRENT RULES: all the following personal protective equipment (PPE) has to be in conformity with relevant technical rules in force (Directive no. 89/656/CEE and following amendments and updates) and therefore has to be EC-marked and have relevant declaration of conformity which usually refers to specific European (EN) technical rules of the harmonized type.
- Page 7 It guarantees the free replacement of the pieces which might break or abnormally wear due to assessed faults of design, supply, construction, or assembly which can be attributed to Omcan; • The request for a free repair has to be directly addressed to Omcan or the dealer where the machine has been purchased; •...
- Page 8 • If there is no invoice or receipt proving the purchase; • Any missed or delayed payment implies the expiry of the validity of the warranty granted by Omcan for the whole period of the missed or delayed payment; •...
-
Page 9: Technical Specifications
Safety and Warranty DO NOT DISCARD ANY PACKAGING MATERIALS IN THE ENVIRONMENT! Technical Specifications Model BS-IT-1524 BS-IT-1829-M Blade Length 60”/ 1524mm 72”/ 1829mm Cutting Capacity 7.5” x 7.3” / 190 x 185mm 10.6” x 8.3” / 270 x 210mm Power 1.5 HP / 1.12 kW... -
Page 10: Installation
Check that (both when the motor is running and when it is idle, but the machine is powered) the efficiency of the power supply and that the protection of the switchboard have been performed. If such checks are passed, the machine is electrically installed; if they are not, contact Omcan for assistance. BLADE GUIDE SLIDING BLOCKS ADJUSTMENT 1. -
Page 11: Blade Tension Adjustment
Installation 3. Unscrew any of the two black (M) small knobs making sure not to unscrew it completely from its seat (S); 4. Bring the white sliding block (P) close to the blade (L) until they come very close; 5. Evaluate the thickness of the sliding block (the sliding blocks of the blade guide continuously wear; they have to be replaced when their thickness is below 1.5 cm) and, if necessary, replace it with a new sliding block;... -
Page 12: Blade Replacement
Installation BLADE REPLACEMENT 1. Make sure that the machine is switched off (rotational device positioned “O” = OFF); 2. Make sure that the machine is not working (blade has stopped); 3. Open the door (H) at least 90°; 4. Disassemble the protection device (R) from the blade necessary to the blade guide (G); 5. -
Page 13: Operation
Installation Operation 1. Make sure that the machine is switched off (rotational device positioned “O” = OFF); 2. Make sure that the machine is not working (blade has stopped); 3. Put the material to cut on the working table; 4. Adjust the height of the blade guide according to the height of the material to cut; 5. -
Page 14: Maintenance
Operation 9. To cut other slices having a different thickness, repeat step 5 onward; 10. If the height of the material to cut varies of more than 1 cm when cutting more slices, go back to 1. Maintenance WARNING! Before any cleaning and/or maintenance and/or check, switch the machine off (rotational device positioned “O”... - Page 15 If damaged or bad working components are detected, do not allow staff to use the machine and put a warning about the prohibition on it; then contact the dealer or Omcan for maintenance. STORAGE AND DISPOSAL In order to preserve the machine for a very long period when switched off the following rules must be abided •...
-
Page 16: Troubleshooting
Turn the ON/OFF switch to “O” position and contact the manufacturer or dealer to have the ON/OFF switch repaired. Door is open but the machine does Damaged door safety microswitch. Contact Omcan or the dealer to not stop. have the door safety microswitch replaced. - Page 17 Saw blade with toothing unsuitable If the material to cut is among for the material to cut. those envisaged for the machine, contact Omcan. or the dealer to have a saw blade suitable for the material to cut, otherwise read below.
- Page 18 One or both pulleys are damaged Check the pulleys and contact or out from their axis. Omcan or the dealer to have them repaired if they are out of their axis. Bad quality of the blade.
-
Page 19: Parts Breakdown
Parts Breakdown Model BS-IT-1524 10252 Model BS-IT-1829-M 17875... -
Page 20: Parts Breakdown
Parts Breakdown Model BS-IT-1524 10252 Model BS-IT-1829-M 17875 Item No. Description Position Item No. Description Position Item No. Description Position Knob of the transporter guide pole for 34880 Opening for 200/220 34891 Tension slide for 200/220 17772 200/220 Knob to close the opening (Complete) -
Page 21: Electrical Schematics
Electrical Schematics Model BS-IT-1524 10252 Model BS-IT-1829-M 17875... -
Page 22: Notes
Notes ________________________________________________________________________________________ ________________________________________________________________________________________ ________________________________________________________________________________________ ________________________________________________________________________________________ ________________________________________________________________________________________ ________________________________________________________________________________________ ________________________________________________________________________________________ ________________________________________________________________________________________ ________________________________________________________________________________________ ________________________________________________________________________________________ ________________________________________________________________________________________ ________________________________________________________________________________________ ________________________________________________________________________________________ ________________________________________________________________________________________ ________________________________________________________________________________________ ________________________________________________________________________________________ ________________________________________________________________________________________ ________________________________________________________________________________________ ________________________________________________________________________________________ ________________________________________________________________________________________ ________________________________________________________________________________________ ________________________________________________________________________________________ ________________________________________________________________________________________ ________________________________________________________________________________________... -
Page 23: Warranty Registration
Warranty Registration Thank you for purchasing an Omcan product. To register your warranty for this product, complete the information below, tear off the card at the perforation and then send to the address specified below. You can also register online by visiting: Merci d’avoir acheté... - Page 24 Since 1951 Omcan has grown to become a leading distributor of equipment and supplies to the North American food service industry. Our success over these many years can be attributed to our commitment to strengthen and develop new and existing relationships with our valued customers and manufacturers.
Need help?
Do you have a question about the BS-IT-1524 and is the answer not in the manual?
Questions and answers