Subscribe to Our Youtube Channel
Related Manuals for Omcan 2000
Summary of Contents for Omcan 2000
-
Page 1: Instruction Manual
Band Saw Model 2000 Instruction Manual Version 1 3115 Pepper Mill Court, Mississauga, ON, L5L 4X5 1-800-465-0234 4450 Witmer Industrial Estates, Unit 4, Niagara Falls, NY, 14305 www.omcan.com... -
Page 2: Table Of Contents
Table of Contents Model 2000 Section Page General Information -------------------------------------------------------------------------------- 3 Safety --------------------------------------------------------------------------------------------- 3 - 6 Warranty ------------------------------------------------------------------------------------------ 6 - 7 Technical Specifications ---------------------------------------------------------------------- 8 - 9 Installation ------------------------------------------------------------------------------------ 10 - 14 Operation ------------------------------------------------------------------------------------------- 15 Maintenance --------------------------------------------------------------------------------- 16 - 17... -
Page 3: General Information
WARNING! Do not use the machine before you have read and understood this handbook, the warnings and/or all diagrams for the machine. Read and fully understand any additions, corrections and any other information, instruction, explanation which Omcan Inc. and/or their technical and commercial network will give you in any way (e-mail, fax, website, letter). -
Page 4: Safety
Omcan Inc. is not responsible for the actions mentioned above and the person in charge of the machine must take care of them. - Page 5 Safety PERSONAL PROTECTIVE EQUIPMENT PERSONAL PROTECTIVE EQUIPMENT IN CONFORMITY WITH CURRENT RULES: all of the following personal protective equipment (PPE) has to be in conformity with relevant technical rules in force (Directive no. 89/656/CEE and following amendments and updates) and therefore has to be EC-marked and have relevant declaration of conformity which usually refers to specific European (EN) technical rules of the harmonized type.
-
Page 6: Warranty
• It guarantees the free replacement of the pieces which might break or abnormally wear due to assessed faults of design, supply, construction, or assembly which can be attributed to Omcan Inc.; • The request for a free repair has to be directly addressed to Omcan Inc. or the dealer where the machine has been purchased;... - Page 7 • If there is no invoice or receipt proving the purchase; • Any missed or delayed payment implies the expiry of the validity of the warranty granted by Omcan Inc. for the whole period of the missed or delayed payment;...
-
Page 8: Technical Specifications
Technical Specifications Single-Phase 110V/1/60Hz Dimensions (± 1 cm) (L× W × H) 54 cm × 47 cm × 89 cm Weight 36 kg Working table (L × W) Fixed, 39 cm × 37.5 cm Max cutting height 26 cm Max cutting width 21 cm Blade guide and Blade protection Manual Setting... -
Page 9: Technical Specifications
Technical Specifications C) MACHINE BODY 1) DRIVING PULLEY Q) DOOR LOCKING KNOB SCREWS D) DOOR 2) PULLEY PATH P) PORTION DEVICE L) WORKING TABLE F) EXIT WASTE OPENING V) BLADE GUIDE SCREWS N) SAW BLADE G) BLADE GUIDE T) BLADE TENSION KNOB Z) BLADE PROTECTOR R) METALLIC GRID M) MICROSWITCH... -
Page 10: Installation
Check that (both when the motor is running and when it is idle, but the machine is powered) the efficiency of the connection and protection of the electrical switchboard have been performed. If such checks are passed, the machine is electrically installed; if they are not, contact Omcan Inc. or the dealer for maintenance. - Page 11 Installation BLADE GUIDE SLIDING BLOCKS ADJUSTMENT 1. Make sure that the machine is switched off (red “O” button is pushed); 2. Make sure that the machine is not working (blade has stopped); 3. Unscrew any of the two black (M) small knobs while paying attention not to unscrew it completely from its seat (S);...
- Page 12 Installation BLADE GUIDE HEIGHT ADJUSTMENT 1. Make sure that the machine is switched off (red “O” button pushed); 2. Make sure that the machine is not working (blade has stopped); 3. Unscrew the black knob (N) (located opposite to the working table of the operator) which, through its integral screw, blocks the rod (A) of the blade guide (G) coming out from machine upper part and the working table;...
-
Page 13: Blade Tension Adjustment
Installation BLADE TENSION ADJUSTMENT 1. Make sure that the machine is switched off (red “O” button pushed); 2. Make sure that the machine is not working (blade has stopped); 3. Screw the black knob (T) located on top to increase the blade tension and unscrew to decrease the blade tension;... - Page 14 Installation 8. Check the correct positioning of the new blade on the two pulleys; 9. Screw the black knob located on the top to increase the interaxle between the two pulleys and increasing the tension of the blade up to the desired value. It should be tight enough so that the blade cannot be extracted from the pulleys from pulling on it;...
-
Page 15: Operation
Operation 1. Make sure that the machine is switched off (red “O” button pushed); 2. Make sure that the machine is not working (blade has stopped); 3. Put the material to cut on the working table; 4. Adjust the height of the blade guide according to the height of the material to cut; 5. -
Page 16: Maintenance
If damaged or bad working components are detected, do not allow anyone to use the machine and put a warning about such prohibition; then contact the dealer or Omcan Inc. for maintenance. STORAGE AND DISPOSAL In order to preserve the machine (which is off) for a very long period the following rules must be abided by: • Disconnect the power cable from the socket;... -
Page 17: Troubleshooting
Maintenance It is also forbidden to leave or dispose the machine or any of its parts in the environment. It is also forbidden to dispose there is still solid urban waste; if the machine is no longer used, deliver it to qualified disposal facilities or authorized dealers. Troubleshooting PROBLEM POSSIBLE CAUSES SOLUTIONS Machine does not start. Lack of power from the electrical Restore the supply of power from network. - Page 18 Troubleshooting Door is open but the machine does Damaged door safety microswitch. Contact Omcan Inc. or the not stop. dealer to have the door safety microswitch replaced. The machine is noisy (vibration, The working table or one of the Add some shims under the working creaking, whistling, etc.).
- Page 19 One or both pulleys are damaged Check the pulleys and contact or out from their axis. Omcan Inc. or the dealer to have them repaired if they are out of their axis. Bad quality of blade.
-
Page 20: Parts Breakdowns
Parts Breakdown Model 2000 10254... -
Page 21: Parts Breakdowns
Parts Breakdown Model 2000 10254 Item Item Item Description Position Description Position Description Position Cutting guide to subdivide to Opening (not interchangeable) 34937 Knob transporter guide (n° 1) 34960 pieces Transporter guide ring nut in Knob of the transporter guide... -
Page 22: Electrical Schematics
Electrical Schematics Model 2000 10254... -
Page 23: Warranty Registration
Warranty Registration Thank you for purchasing an Omcan product. To register your warranty for this product, complete the information below, tear off the card at the perforation and then send to the address specified below. You can also register online by visiting: www.omcan.com/warrantyregistration.html For mailing in Canada For mailing in the US OMCAN INC. OMCAN PRODUCT WARRANTY REGISTRATION... - Page 26 Over the last 60 years, Omcan has grown to become a leading supplier to the food service industry in Canada and the USA. Our success over these many years is directly attributed to our established relationships with all of our valued customers and through providing them with Diverse, Dependable and Proven products.
Need help?
Do you have a question about the 2000 and is the answer not in the manual?
Questions and answers